Instruction Manual

Contents

• Cover Plate
• Gasket
• #6-32 Screw
• Gasket Support Plate
• #8-32 Screw

General Information

1. NOTICE: For Installation by a qualified person in accordance with national and local electrical codes.

2. WARNING: Risk of Electrical Shock or Death. Disconnect power before installing

3. NOTICE: For Indoor Use Only.

NOTES

Before beginning install, remove any debris from non-metallic floor box. Follow manufacturer's instructions to secure conduit and pull wire thru

If you are using data port and data/low-volt cables, you must ensure you are using a non-metallic box with required data divider

COVER AND LEVELING or ADAPTER RING

Our cover is designed to work with many "standard" leveling rings & their associated non-metallic boxes on the market.

Please ensure you verify fit of our cover plate to your leveling or adapter ring and associated floor box before install.

INSTALLATION

1. Ensure equipment is grounded through green screw on leveling/adapter ring (A). If required with your ring, connect a grounding jumper wire from ring lug (A) to device (G) screw.
2. Fasten device to leveling/adapter ring using screws included with receptacle (sold separately).
3. Follow Device Installation and Wiring instructions shown in Figure 2.
4. Place metal support plate, gasket(s), and plastic cover plate over receptacle and fasten using #6-32 screw (feed cat5 cable through data holes before fastening if using CANTEX ring and cable is pre-terminated).
5. Fasten plastic cover plate to leveling ring using 3 provided screws #8-32.
6. Apply small bead of clear silicone type RTV sealant to underside flange of cover plate to seal out scrub water.
7. Insert Assembled leveling ring, device and cover plate into the floor box, pressing snug with floor.

Figure 2. WIRING DIAGRAM

Diagram shows a wiring setup for a receptacle within a floor box. Key components labeled: Neutral (White wire), Hot (Black wire), Ground (Green or bare wire). Connection points are labeled 'G' for the ground screw on the receptacle and 'A' for a lug on the leveling/adapter ring. A note indicates: "This wire connects to the RECEPTACLE with the ground wire". The diagram illustrates connections between the receptacle, the leveling ring, and the box, with wires passing through a conduit.

Components depicted: Receptacle, Ground screw (G), Leveling/Adapter Ring lug (A), Grounding wire, Hot wire, Neutral wire, Gasket Support Plate.

INSTALLATION DRAWING

The drawing illustrates the components for installing the floor box cover. It shows an exploded view of the assembly:

• Top: Two screws for attaching the cover plate.
• Middle: Cover Plate, Gasket, Gasket Support Plate.
• Below: Receptacle, Leveling Ring, Box.
• Side: A diagram labeled 'A' shows the leveling ring with a lug for grounding.
• A separate callout indicates "ITEMS SOLD SEPARATELY" for the Box and Receptacle.

Leveling Ring Fitment with 8100PVG

WARRANTY

Adamax warrants to the Purchaser that the Newhouse Electric by Adamax products sold will be free from defects in workmanship or material under normal use and service for a period of 1 year when stored, installed, operated or maintained in accordance with recommendations of Adamax and standard industry practice and when used under proper and normal use. Adamax does not cover ordinary wear and tear, abuse, misuse, overloading, altered products, systems, or materials not of its own manufacture. Adamax shall in no event be responsible or liable for modifications, alterations, misapplication or repairs made to its products by the Purchaser or others, or for damage caused thereto by negligence, accident or improper use by the Purchaser or others. This warranty does not include reimbursement for the expenses of labor, transportation, removal or reinstallation of the products.

DISCLAIMER OF WARRANTY: THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER WRITTEN, ORAL, EXPRESSED OR IMPLIED. THERE ARE NO WARRANTIES OF MERCHANTABILITY OR FITNESS OF ANY PRODUCT FOR A PARTICULAR PURPOSE.

IN NO EVENT AND UNDER NO CIRCUMSTANCES SHALL ADAMAX INC BE LIABLE TO THE PURCHASER OR TO ANY OTHER PERSON FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL OR INCIDENTAL LOSSES OR DAMAGES, INCLUDING, WITHOUT LIMITATION, DAMAGE TO OR LOSS OF USE OF ANY PRODUCT, LOST SALES, OR PROFITS, OR DELAY OR FAILURE TO PERFORM ITS WARRANTY OBLIGATION, OR CLAIMS OF THIRD PARTIES AGAINST THE PURCHASER, ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, USE OF, INABILITY TO USE, OR THE REPAIR OR REPLACEMENT OF, ADAMAX's PRODUCTS. As stated herein, the term "person" shall include, without limitation, any individual proprietorship, partnership, corporation or entity.