TKO Strength & Performance
Instructions for TKO models including: 9050 Functional Trainer, 9050, Functional Trainer, Trainer
TKO Strength 9050 Functional Trainer Cable Machine
TKO Strength Functional Trainer, Graphite — Active Fitness Depot
TKO Strength Functional Trainer Machine in Graphite 9050 — Home Gym Gurus
File Info : application/pdf, 11 Pages, 1.08MB
DocumentDocumentFunctional Trainer Model 9050 www.tko.com Owner's Manual 2 Product Diagram Exploded Diagram Parts List Parts List No. Description 1 Left Upright Frame 2 Right Upright Frame 3 Rear Lower Support Frame 4 Top Support Frame 5 Left Slide Frame 6 Right Slide Frame 7 Front Wheel Bracket 8 Pulley Frame 9 Adjusting Square Tube F40*2 10 Guide Rod Ø20*1763 11 Cleat for Shroud 86*25*4 12 Guide Rod Bush 30*20.2*30 13 Pulley Bushing 18*14 14 Weight Stack 260*100*25.4 15 Top Weight Plate 247*65*25.4 16 Selector Rod Ø25*595 17 Bearing Washer Ø25*Ø21*1 18 Curl Cover 107.6*62*3 19 Bushing Ø10.2*Ø12.7*5.5 20 Pin Ø18*Ø12*118*M10 21 Spring Ø14*Ø1.5*55 22 Roller Ø54*49 23 Knob Ø45*66 24 Ring Ø33*10 25 Magnetic Pin 10*98 26 Cable Ø5*7600 27 Pulley Ø115*27.5 28 PVC Foot Pad 169*129*16 29 Cushion Ø80*25 30 Shroud 1700*600*4 31 Sleeve Ø12*55 32 Rubber Bumper 60*50*6 33 Rear Top Support Frame 34 T-Shaft Ø25*102 35 Limited Plate 65*30*80*4 QTY No. Description 1 36 Bearing 61800ZZ 1 37 Bearing 61804ZZ 1 38 Pulley 95*24 1 39 End Cap PT 50*100*3 1 40 Foam Grip Ø24*3*345mm 1 41 Foam Grip Ø24*3*160mm 2 42 Foam Grip Ø24*3*290mm 2 43 Hex Socket Head Bolt M10*50 2 44 Hex Socket Head Bolt M10*65 4 45 Hex Socket Head Bolt M10*45 16 46 Hex Socket Head Bolt M10*25 4 47 Hex Socket Head Bolt M8*15 8 48 Nut M10 40 49 Hex Socket Head Bolt M10*75 1 50 Hex Sunk Screw M8*20 2 51 Hex Socket Head Bolt M6*15 2 52 Flat Washer Ø11*Ø20*2 2 53 Big Washer Ø8.6*Ø22*2 12 54 Rubber Washer Ø7*Ø2*3T 2 55 Hex Socket Head Bolt M5*10 2 56 Hex Socket Head Bolt M10*70 6 57 Limited Cushion 30*70*20 2 58 Cross Pan Screw M6*12 6 59 Small Rubber Sleeve 15*6*18 2 60 Cross Sunk Screw M5*10 2 61 O-Ring Ø19*1.8 14 62 Hex Cone Set Screw M6*4 4 63 Hex Cone Set Screw M6*6 4 64 Hex Socket Head Bolt M10*40 2 65 Flat Nut M12 6 66 Big Washer Ø9*Ø24*2 2 67 Right Top Weight Plate 1 68 End Cap Ø34.5*Ø6.5*25 2 69 Hex Socket Head Bolt M6*20 2 QTY 12 4 4 6 2 2 2 10 6 4 12 18 30 6 8 36 64 16 16 10 4 2 4 4 8 4 10 12 2 2 2 1 8 8 Parts List 70 Long Bar 1 71 Short Handle 1 72 Tricep Rope 1 73 Ankle Strap 1 74 Chains 2 75 Hand Grips 2 76 Safety Hooks 6 Assembly Note: Before starting assembly remove all parts and hardware from the carton, ensure you have everything according to the list. Step 1 Install Rear Lower Support Frame (3), Rear Top Support Frame (33) and Rear Top Support Frame (4) onto Left Frame (2) and Right Frame (1), using Hex Bolt M10*25 (46) and Flat Washer 11*20*2 (52). Assembly Step 2 Loosen and remove 2 Guide Rod Bush (12) from the Guide Rod (10); Then remove the Top Weight Plate (15) and The Selector Rod assembly from the Guide Rods. Assembly Step 3 Re-Insert both Guide Rod (10) into the holes on the bottom of the Main Frame; Make sure the Rubber Bumpers are at the bottom of the Guide Rods. Assembly Step 4 Install 20 Weight Stack (14) onto the Guide Rod (10); Re-install the Top Weight Plate (15) and Selector Rod assembly onto the top of the Weight Stack; Make Sure the holes of the Weight Stack for the Magnetic Lock Pin are the same direction. Assembly Step 5 First Re-install the Guide Rod Bush (12) that was removed in STEP 2; Then tighten both Hex Screw M 6*4 (62) with a wrench; Repeat the same procedure for the other side.