Support for businesses in Australia | business.gov.au
Lawn & Garden Equipment | Innovative Power Tools | WORX
Instruction Manual for WORX NITRO models including: WX693 WX693.X Sonicrafter, WX693, WX693.X, WX693 Sonicrafter, WX693.X Sonicrafter, Sonicrafter
3 Oscillating Tool WX693 WX693.X damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean.
NITRO Sonicrafter brushless cordless oscillating multi-tool 20V - with battery and charger | WORX
File Info : application/pdf, 12 Pages, 1.92MB
DocumentDocumentSAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS Oscillating Tool WX693 WX693.X PRODUCT SAFETY GENERAL POWER TOOL the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. SAFETY WARNINGS b) Use personal protective equipment. Always wear eye protection. Protective equipment WARNING Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or batteryoperated (cordless) power tool. carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may 1) Work area safety a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust 2) Electrical safety collection can reduce dust-related hazards. 2 a) Power tool plugs must match the outlet. Never h) Do not let familiarity gained from frequent use modify the plug in any way. Do not use any of tools allow you to become complacent and adapter plugs with earthed (grounded) power ignore tool safety principles. A careless action tools. Unmodified plugs and matching outlets will can cause severe injury within a fraction of a reduce risk of electric shock. second. b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. 4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source and/ or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. 3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under e) Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If Oscillating Tool WX693 WX693.X damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. SAFETY INSTRUCTION FOR CUTTING f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock. operations different from those intended could result in a hazardous situation. h) Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe SAFETY WARNINGS FOR BATTERY PACK handling and control of the tool in unexpected situations. a) Do not dismantle, open or shred cells or battery pack. 5) Battery tool use and care b) Do not short-circuit a battery pack. Do not store battery packs haphazardly in a box or drawer a) Recharge only with the charger specified by the where they may short-circuit each other or be manufacturer. A charger that is suitable for one short-circuited by conductive materials. When type of battery pack may create a risk of fire when battery pack is not in use, keep it away from other used with another battery pack. metal objects, like paper clips, coins, keys, nails, b) Use power tools only with specifically designated battery packs. Use of any other battery packs screws or other small metal objects, that can make a connection from one terminal to another. may create a risk of injury and fire. Shorting the battery terminals together may c) When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, cause burns or a fire. c) Do not expose battery pack to heat or fire. Avoid storage in direct sunlight. that can make a connection from one terminal to another. Shorting the battery terminals together d) Do not subject battery pack to mechanical shock. 3 may cause burns or a fire. e) In the event of battery leaking, do not allow the d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact liquid to come into contact with the skin or eyes. If contact has been made, wash the affected area accidentally occurs, flush with water. If liquid with copious amounts of water and seek medical contacts eyes, additionally seek medical help. advice. Liquid ejected from the battery may cause f) Keep battery pack clean and dry. irritation or burns. g) Wipe the battery pack terminals with a clean dry e) Do not use a battery pack or tool that is damaged cloth if they become dirty. or modified. Damaged or modified batteries may h) Battery pack needs to be charged before use. exhibit unpredictable behaviour resulting in fire, Always refer to this instruction and use the explosion or risk of injury. correct charging procedure. f) Do not expose a battery pack or tool to fire i) Do not maintain battery pack on charge when not or excessive temperature. Exposure to fire or in use. temperature above 130 °C may cause explosion. g) Follow all charging instructions and do not j) After extended periods of storage, it may be necessary to charge and discharge the charge the battery pack or tool outside the battery pack several times to obtain maximum temperature range specified in the instructions. Charging improperly or at temperatures outside performance. k) Recharge only with the charger specified by the specified range may damage the battery and Worx. Do not use any charger other than that increase the risk of fire. specifically provided for use with the equipment. 6) Service a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. b) Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers. l) Do not use any battery pack which is not designed for use with the equipment. m) Keep battery pack out of the reach of children. n) Retain the original product literature for future reference. o) Remove the battery from the equipment when not in use. p) Dispose of properly. Oscillating Tool WX693 WX693.X q) Do not mix cells of different manufacture, capacity, size or type within a device. r) Keep the battery away from microwaves and high pressure. SYMBOLS To reduce the risk of injury, user must read instruction manual Warning Avoid danger of injury from the sharp edges of the accessories. Accessories can become very hot while working, presenting danger of burns! Make sure the battery is removed prior to changing accessories. Wear protective gloves Wear ear protection High oscillation frequency. Wear eye protection Low oscillation frequency. Wear dust mask 4 -- -- --= LED light is a battery capacity indicator and will flash when power gets low . Li-I on Li-Ion battery This product has been marked with a symbol relating to `separate collection' for all battery packs and battery pack. It will then be recycled or dismantled in order to reduce the impact on the environment. Battery packs can be hazardous for the environment and for human health since they contain hazardous substances. Li-I on Batteries may enter water cycle if disposed improperly, which can be hazardous for ecosystem. Do not dispose of waste batteries as unsorted municipal waste. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. RCM marking ABN: Australian Business Number. By this number, business information such as entity type, status, business location etc. can be found at website http://abr. business.gov.au. ABN of Positec Australia Pty Limited is 14 101 682 357 Do not burn Oscillating Tool WX693 WX693.X 1 2 4 3 5 7 5 6 A 1 2 3 B 1 2 Oscillating Tool WX693 WX693.X C D E 6 ON F OFF G H -- -- --= 1 2 Oscillating Tool WX693 WX693.X COMPONENT LIST SUGGESTED BATTERIES 1. HYPERLOCKTM ACCESSORY CLAMPING LEVER 2. ON/OFF SWITCH 3. VARIABLE SPEED DIAL 4. VENTING SLOTS 5. UNIVERSAL-FITTM ACCESSORY INTERFACE* 6. SMALLER FLANGE (FOR OTHER BRANDS' SANDING PADS) AND CHARGERS Category 20V Battery Model WA3550 WA3550.1 WA3551 WA3551.1 WA3553 Capacity 1.5Ah 1.5Ah 2.0Ah 2.0Ah 4.0Ah 7. FLANGE * Works with other oscillating tool brands' accessories. The following compatible brands are trademarks owned by third parties which may be registered by their respective owners: Black & Decker®, Bosch®, Chicago Electric®, Craftsman®, Dremel®, Fein®, Genesis®, Makita®, Mastercraft®, Milwaukee®, Performax®, Porter Cable®, Ridgid®, Ryobi®, Skil®, and Tool Shop®. Not all the accessories illustrated or described are included in standard delivery. 20V Charger WA3860 WA3880 2.0A 2.0A We recommend that you purchase your accessories from the same store that sold you the tool. Refer to the accessory packaging for further details. Store personnel can assist you and offer advice. NOISE INFORMATION A weighted sound pressure LpA: 84.9dB(A) TECHNICAL DATA Type WX693 WX693.X (6-designation of machinery, representative of high frequency oscillation tool) A weighted sound power KpA&KwA Wear ear protection LwA: 95.9dB(A) 3.0dB(A) 7 WX693 WX693.X** Voltage Oscillations speed Oscillation angle Machine weight(Bare tool) 20V Max*** 8000-18000 /min 4° 1.0kg **X=1-999, A-Z, M1-M9 there are only used for different customers, there are no safe relevant changes between these models. ***Voltage measured without workload. Initial battery voltage reaches maximum of 20 volts. Nominal voltage is 18 volts. VIBRATION INFORMATION Vibration total values (triax vector sum) determined according to EN 62841: Typical weighted vibration Vibration emission value ah = 3.910m/s2 Uncertainty K = 1.5m/s² The declared vibration total value and the declared noise emission value have been measured in accordance with a standard test method and may be used for comparing one tool with another. The declared vibration total value and the declared noise emission value may also be used in a preliminary assessment of exposure. WARNING: The vibration and noise emissions during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used especially what kind of workpiece is processed dependant on the following examples and other variations on how the tool is Oscillating Tool WX693 WX693.X used: How the tool is used and the materials being cut or drilled. The tool being in good condition and well maintained. The use of the correct accessory for the tool and ensuring it is sharp and in good condition. The tightness of the grip on the handles and if any anti vibration and noise accessories are used. And the tool is being used as intended by its design and these instructions. Remove or install battery pack LED Light See Fig. G See Fig. H The Variable Speed Dial can be used to set the optimum oscillating frequency according to the accessories used and the respective application. Oscillation frequency Application This tool may cause hand-arm vibration syndrome if its use is not adequately managed. High oscillation frequency: Sanding, Sawing, Rasping and Polishing Stone and Metal. WARNING: To be accurate, an estimation of exposure level in the actual conditions of use should also take account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle but not actually doing the job. This may significantly reduce the exposure level over the total working period. Helping to minimise your vibration and noise exposure risk. Always use sharp chisels, drills and blades. Maintain this tool in accordance with these instructions and keep well lubricated (where appropriate). If the tool is to be used regularly then invest in anti 8 vibration and noise accessories. Plan your work schedule to spread any high vibration tool use across a number of days. Low oscillation frequency: Scraping, Polishing Varnishes. OPERATING INSTRUCTIONS NOTE: Before using the tool, read the instruction book carefully. INTENDED USE: The power tool is intended for sawing and remodelling wooden materials, plastic, plaster, non- ferrous metals and fasteners (e.g. nails and clamps) as well as for working on soft wall tiles and for dry grinding of small surfaces. It is especially suitable for working close to edges and for flush cutting. ASSEMBLY AND OPERATION Action Figure Mounting accessories Mounting the sanding sheet Operating the on/off switch Using the variable speed dial See Fig. A-C See Fig. D See Fig. E See Fig. F Oscillating Tool WX693 WX693.X APPLICATION WARNING: The sawing teeth are very sharp. Do not touch during mounting and application. The workpiece must be clamped tightly before the operation. Sawing Pic Description Application Universal Metal/Wood End Cut Blade Wood, plastic, fiberglass, nails, nonferrous metals, thin sheet metal, hardened fillers Standard Wood End Cut Blade Wood, plastic, drywall Precision Wood Cut Blade Wood, soft plastics HSS Semicircle Saw Blade Thin wood, plastic, fiberglass, nonferrous metals, thin sheet metal, hardened fillers, window glazing Sanding Sanding Pad (Perforated) Sanding Finger Pad Wood, plastic, hardened fillers 9 Wood, plastic, hardened fillers Rasping Triangular Carbide Grit Rasp Wood, hardened adhesives, thin set, masonry Carbide Rasp (Finger Shaped) Wood, hardened adhesives, thin set, masonry Removing grout Scraping Carbide Grit Semicircle Saw Blade Diamond-Coated Semicircle Saw Blade Rigid Scraper Blade Flexible Scraper Blade Grout, porous concrete, masonry Ceramic and stone tile, backerboard Old paint, hardened adhesives, caulk, carpet Elastic sealants, paint, adhesive residues, carpet We recommend that you purchase your accessories listed in the above list from the same store that sold you Oscillating Tool WX693 WX693.X the tool. Refer to the accessory packaging for further details. Store personnel can assist you and offer advice. NOTE: When plunging and sawing use a slight pendulum motion, to allow sufficient chip removal. The saw blade lasts longer if the wear is distributed evenly. To ensure an even distribution, loosen the saw blade, rotate it and retighten firmly. Cut/Sand with a constant movement and light pressure. Heavy pressure does not increase the cut/removal rate the accessory merely wears faster. FOR BATTERY TOOLS: The ambient temperature range for tool and battery use and storage is 0oC-45oC. The recommended ambient temperature range for the charging system during charging is 0oC-40oC. Positec Australia Pty Limited 10 Corporate Blvd Bayswater , VIC 3153, Australia ENVIRONMENTAL PROTECTION WORKING HINTS FOR YOUR Waste electrical products should not be TOOL If your power tool becomes too hot, especially when used at low speed, set the speed to maximum and run disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. it with no load for 2-3 minutes to cool the motor. Avoid prolonged usage at very low speeds. Always keep the blade sharp. Always ensure the workpiece is firmly held or clamped to prevent movement. Any movement of the material may affect the quality of the cutting or sanding finish. Start your tool before working and turn it off only after you stop working. 10 Do not start sanding without having the sandpaper fitted. Do not allow the sandpaper to wear away , it will damage the sanding pad. The guarantee does not cover sanding pad wear and tear. Use coarse grit paper to sand rough surfaces, medium grit for smooth surfaces and fine grit for finishing surfaces. If necessary, first make a test run on scrap material. Excessive force will reduce the working efficiency and cause motor overload. Replacing the accessory regularly will maintain optimum working efficiency. MAINTAIN TOOLS WITH CARE Your power tool requires no additional lubrication or maintenance. There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust. Oscillating Tool WX693 WX693.X DECLARATION OF CONFORMITY We, Positec Germany GmbH Postfach 32 02 16, 50796 Cologne, Germany On behalf of Positec declare that the product, Description WorxNITRO Sonicrafter® Type WX693 WX693.X (6-designation of machinery, representative of high frequency oscillation tool) Function Sanding, sawing, rasping, scraping, polishing Complies with the following Directives, 2006/42/EC 2014/30/EU 2011/65/EU&(EU)2015/863 Standards conform to EN 62841-1 EN 62841-2-4 EN 55014-1 EN 55014-2 The person authorized to compile the technical file, Name Marcel Filz Address Positec Germany GmbH Postfach 32 02 16, 50796 Cologne, Germany 11 2022/03/01 Allen Ding Deputy Chief Engineer, Testing & Certification Positec Technology (China) Co., Ltd 18, Dongwang Road, Suzhou Industrial Park, Jiangsu 215123, P. R. China Oscillating Tool WX693 WX693.X DECLARATION OF CONFORMITY We, Positec (UK & Ireland) Ltd., PO Box 6242, Newbury, RG14 9LT, UK On behalf of Positec declare that the product, Description WorxNITRO Sonicrafter® Type WX693 WX693.X (6-designation of machinery, representative of high frequency oscillation tool) Function Sanding, sawing, rasping, scraping, polishing Complies with the following regulations: Supply of Machinery (Safety) Regulations 2008 Electromagnetic Compatibility Regulations 2016 The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations Standards conform to BS EN 62841-1 BS EN 62841-2-4 BS EN 55014-1 BS EN 55014-2 The person authorized to compile the technical file, Name Jim Kirkwood Address Positec (UK & Ireland) Ltd., PO Box 6242, Newbury, RG14 9LT, UK 12 2022/03/01 Allen Ding Deputy Chief Engineer, Testing & Certification Positec Technology (China) Co., Ltd 18, Dongwang Road, Suzhou Industrial Park, Jiangsu 215123, P. R. China Oscillating Tool After-sales Service and Application At www.worx.com you can order spare parts or arrange the collection of a product in need of servicing or repair. Tel. Service: 0345 202 9679 E-Mail: customerservices@worxtools.com www.worx.com Copyright © 2022, Positec. All Rights Reserved. AP01163207 WX693 WX693.X