Clarke AC80 Automatic Battery Charger

Introduction

Thank you for purchasing this CLARKE Battery Charger. Please read this manual thoroughly before attempting to operate, and carefully follow all instructions given. It is vitally important that ALL precautions are taken, as specified, which will not only provide protection for yourself and that of others around you, but will also ensure that the Battery Charger will give you long and satisfactory service. This battery charger is limited to use with 12V lead acid/ gel including MF (Sealed) and Leisure batteries ONLY. DO NOT attempt to charge other types of battery.

Guarantee

This CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt as proof of purchase. This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended. Faulty goods should be returned to their place of purchase; no product can be returned without prior permission. This guarantee does not affect your statutory rights.

Environmental Recycling Policy

Through purchase of this product, the customer is taking on the obligation to deal with Waste Electrical and Electronic Equipment (WEEE) in accordance with WEEE regulations relating to treatment, recycling, recovery, and environmentally sound disposal. This means the product must not be disposed of with general household waste but must be disposed of according to laws governing WEEE at a recognised disposal facility. ♻️

Safety Precautions

• ❗ IMPORTANT: ALWAYS disconnect the battery from the vehicle BEFORE connecting the charger leads. This is to prevent damage to the vehicle's electronic system.
• This battery charger is designed for INDOOR use ONLY. Do not use outdoors, exposed to the elements.
• Do not use for any other type of battery, or supply power to low voltage electrical systems.
• Connect the battery clamps to the battery terminals before plugging the charger into the mains power supply.
• This battery charger is limited to use with 12V lead acid/ gel including MF (Sealed) and Leisure batteries ONLY. DO NOT attempt to charge other types of battery.
• Do not attempt to charge a battery with a capacity exceeding that indicated in the 'Specifications'.
• Do not operate the charger if any of the cables are damaged. Consult your Clarke dealer for repair or replacement.
• Do not operate the charger if the case is damaged. Consult your Clarke dealer for inspection and repair.
• Do not disassemble the charger; incorrect reassembly may result in electric shock or fire.
• Ensure the battery posts and battery clamps are perfectly clean before use.
• Disconnect from the mains power supply before making or breaking connections to the battery.
• Make sure the battery is topped up with distilled water (where applicable) to its proper level before connecting the charger.
• Unscrew the battery filler caps fully (where applicable) and leave them loose for the duration of charge to ensure that gases are allowed to escape.
• ? NOTE: ALWAYS clean around the filler caps thoroughly before unscrewing to ensure that no dirt can enter the battery cell. Ensure the breather holes in the caps are perfectly clear before screwing in again.
• When charging is complete, disconnect the negative cable first and then the positive cable.
• Always place the charger in an environment which is:
  • well ventilated
  • out of the reach of children
  • not exposed to direct sunlight or heat source
  • away from water / moisture, oil and grease
  • away from explosive gases, flames, and sparks
  • away from any flammable substance

Electrical Connections

THIS APPLIANCE IS DOUBLE INSULATED. This appliance is fitted with a 13 amp, BS 1363 plug which should be connected to a standard 230 VAC (50Hz) electrical supply. If the plug is replaced, the replacement must be to the same specification and wired in accordance with the following code:

• Blue - Neutral
• Brown - Live

As the colours of the flexible cord may not correspond with the coloured markings identifying terminals in your plug, proceed as follows:

• Connect BROWN cord to terminal marked with a letter "L" or coloured RED.
• Connect BLUE cord to terminal marked with a letter "N" or coloured BLACK.

If in doubt, consult a qualified electrician.

In the event a moulded plug is fitted and subsequently cut from the electric cable, the replacement plug MUST be an approved 5 amp, BS 1363 plug and wired in accordance with the above instructions. Additionally, please note:

• The discarded plug must be thrown away as there is a danger of electric shock if it is subsequently inserted into a socket outlet.
• Never use the plug without the fuse cover fitted.
• Should you wish to replace a detachable fuse carrier, ensure that the correct replacement is used (as indicated by marking or colour code).
• Replacement fuse covers can be obtained from your local dealer or most electrical stockists.

Fuse Replacement

The fuse in the plug must be replaced with one of the same rating (5 amps) and this replacement must be ASTA or BSI approved to BS1362.

Extension Cables

If an extension cable is used, the conductors in the cable MUST be a minimum 1.5mm². Additionally, ensure the cable is completely unwound from the drum.

Using the Charger

This model is a fully automatic charger (will shut off when fully charged) for any type of battery up to a capacity of 15-120AH. This charger will not charge a totally flat battery; the battery must be able to supply a minimum of 3 Volts before charging will commence.

LED Indicators

Disconnecting the Battery from the Vehicle

If the battery is still in the vehicle, ensure the battery terminals are disconnected from the vehicle's electrical system. Disconnect the negative (EARTH) terminal first, followed by the positive terminal. (When reconnecting, do so in reverse order).

Connecting the Charger to the Battery

1. Connect the red battery clamp to the positive (+ve) battery terminal.
2. Connect the black clamp to the negative (-ve) terminal.
3. Make sure that both connections are secure and NOT touching each other.
4. Select the battery type (normal or gel cell) using the selector switch.
5. Select the charging speed required (trickle charge or fast charge).

Charging the Battery

Plug in the charger and switch ON at the mains supply to commence charging. When charging is complete, the green Fully Charged LED will light up. The charger may be left connected; it will monitor the battery and provide a top-up charge when necessary.

Disconnecting the Charger

1. Switch OFF at the mains supply.
2. Remove the black clamp from the negative (-ve) terminal first.
3. Then remove the red clamp from the positive (+ve) terminal.
4. Reconnect the battery to the vehicle.

Safety Features

Whenever a fault condition exists, the circuitry automatically disengages the normal operation of the charger.

Thermal Overload

The thermal overload protector provides a safeguard against an excessively large charging current being drawn by the battery for prolonged periods.

Short Circuit

The charger is fully protected against short circuits, i.e. the clamps coming into contact, directly or indirectly, when the unit is switched ON. If a short circuit happens, the charger will switch off and return to normal after one or two minutes.

Reverse Polarity

The charger is fully protected against the possibility of the clamps being incorrectly connected. If the Polarity Warning LED illuminates, the clamps connected to the battery should be reversed.

Specifications

Declaration of Conformity

This document declares that the Clarke AC80 Battery Charger complies with relevant UK and EU regulations and directives, including Electromagnetic Compatibility, Low Voltage, and Restriction of Hazardous Substances. It has been tested against applicable standards. The UKCA mark was first applied in 2022, and the CE mark was first applied in 2012. The product description is '12V Battery charger', Model AC80.

[UKCA Mark] [CE Mark]

Contact Information

For Parts & Service:

Phone: 020 8988 7400

Email: Parts@clarkeinternational.com or Service@clarkeinternational.com

Website: www.clarkeinternational.com