TÜV Rheinland Test Report - Products

Prüfbericht-Nr.: CN25QX0Y 001

Client Reference No.: 1288983

Client: IKEA of Sweden AB, Box 702, SE-343 81 Älmhult, Sweden

Test Item: Self-ballasted LED lamps

Identification / Type no.: LED2410R5NA

Order Content: TÜV Rheinland EMC service

Test Specification: FCC 47 CFR Part 15, Subpart B:2023 Class B, ICES-005:2018, ICES-003:2020

Date of Sample Receipt: 2025-03-18

Testing Period: Refer to test report

Place of Testing: Refer to clause 1.1

Testing Laboratory: TÜV Rheinland (Shanghai) Co., Ltd.

Test Result: Pass

Tested by: Jessie Xu (Project engineer)

Authorized by: Jiang Zhou (Authorizer)

Issue Date: 2025-05-10

Other Information: FCC ID: FHO-LED2410R5NA, Test Firm Name: TUV Rheinland (Shanghai) Co., Ltd., Designation Number: CN1396, Test Firm Registration Number: 930979

Condition of the test item at delivery: Test item complete and undamaged.

Remarks:

• All test equipment used was calibrated according to the laboratory's calibration program and meets relevant standards. Traceability is ensured by the management system. Detailed information on test conditions, equipment, and measurement uncertainty is available upon request.
• This document is digitally signed as agreed. TÜV Rheinland has not verified legal or other requirements applicable to this document; this is the user's responsibility. Validity of the digital signature can be confirmed by a separate document upon request.
• Test clauses marked with * were subcontracted. Deviations from specifications are listed in the report.
• The decision rule for conformity statements is based on the "Zero Guard Band Rule" and "Simple Acceptance" in accordance with ILAC G8:2019 and IEC Guide 115:2021, without considering measurement uncertainty.

General Product Information

The Equipment Under Test (EUT) is an ordinary self-ballasted LED lamp for lighting and similar use. For further information, refer to the user's manual.

Ratings and System Details

• Rated Input: AC 120 V, 60 Hz, 60 mA
• Rated Power: 5 W
• RF IC: SiMG301

Independent Operation Modes

The basic operation modes are "ON" and "OFF". The test modes used were:

• Mode 1: Warm lighting with the maximum lighting output.
• Mode 2: Warm lighting with the minimum lighting output.
• Mode 3: White lighting with the maximum lighting output.
• Mode 4: White lighting with the minimum lighting output.

Highest Frequency Generated or Used

The highest frequency used in the EUT is 2480 MHz.

Submitted Documents

Circuit diagram, user's manual, and rating label were submitted.

Test Set-up and Operation Modes

Principle of Configuration Selection: The EUT was configured to measure its highest possible emission level. Test conditions were adapted according to the instructions for use.

Sequence of Testing:

1. Conducted emission tests: 2025-01-20
2. Radiated emission tests: 2025-01-18 to 2025-02-07

Equipment and Cable Arrangement

Conducted Emission Setup: The setup includes the EUT, LISN (Line Impedance Stabilization Network), EMI receiver, Computer, Transformer, and Power Supply. The EUT is placed on a wooden support 0.8m away from the AMN. Excess cable length is folded to form a bundle of 0.3-0.4m.

Radiated Emission Setup (30-1000 MHz): The setup involves the EUT on a turntable, an antenna at a distance of 3m, and absorbers. The antenna height is varied from 1m to 4m, and the turntable rotates 360° to find maximum disturbance. The antenna is tested in both horizontal and vertical polarizations.

Radiated Emission Setup (1-18 GHz): Similar to the 30-1000 MHz setup, but within an absorber-lined semi-anechoic chamber, with the antenna at 3m distance from the EUT.

Test Software

The "Home" APP for iPhone was used.

Special Accessories and Auxiliary Equipment

Countermeasures to achieve EMC Compliance

No special countermeasures were employed during the tests.

Conformity Decision Rule

For all EMI tests, compliance is determined by comparing measurement results directly with limits, as measurement uncertainties are less than the values specified in CISPR 16-4-2.

Test Results EMISSION

Emission in the Frequency Range up to 30 MHz

Conducted emission

Result: Passed

Date of Testing: 2025-04-11

Test Procedure: FCC 47 CFR Part 15, Subpart B:2023, ICES-005:2018, ICES-003:2020, ANSI C63.4-2014 and CISPR 16-2-1

Frequency Range: 0.15 – 30 MHz

Limits:

• Quasi-peak limit: 0.15-0.5 MHz: 66 to 56 dBμV (decreasing with frequency); 0.5–5 MHz: 56 dBμV; 5–30 MHz: 60 dBμV
• Average limit: 0.15-0.5 MHz: 56 to 46 dBμV (decreasing with frequency); 0.5–5 MHz: 46 dBμV; 5–30 MHz: 50 dBμV

Bandwidth of EMI receiver: 9 kHz

Measurement Time: 1 s

Kind of Test Site: Shielded room

Input Voltage: AC 120 V, 60 Hz

Operational Modes Tested: Mode 1 (Warm max), Mode 2 (Warm min), Mode 3 (White max), Mode 4 (White min).

Ambient Condition: Temperature: 20.1 °C; Relative humidity: 49.5 %

Expanded Measurement Uncertainty (k=2): 2.33 dB

The minimum margin to the limit was 5.29 dB at 0.156750 MHz. The margin is higher than the expanded measurement uncertainty.

The measurement setup followed ANSI C63.4-2014 in a shielded room. Test equipment complies with CISPR 16-1 standards. The disturbance voltage was tested on the neutral and phase lines.

Spectral Diagrams and Measurement Results (Conducted Emission)

Figure 1: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, L, Mode 1

Figure 2: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, N, Mode 1

Figure 3: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, L, Mode 2

Figure 4: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, N, Mode 2

Figure 5: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, L, Mode 3

Figure 6: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, N, Mode 3

Figure 7: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, L, Mode 4

Figure 8: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, N, Mode 4

Emission in the Frequency Range above 30 MHz

Radiated emission (30-1000 MHz)

Result: Passed

Date of Testing: 2025-04-11

Test Procedure: FCC 47 CFR Part 15, Subpart B:2023, ICES-005:2018, ICES-003:2020, ANSI C63.4-2014 and CISPR 16-2-3

Product Classification: Class B

Frequency Range: 30 – 1000 MHz

Limits (3 m distance):

• 30 – 88 MHz: 40 dBμV/m
• 88 – 216 MHz: 43.5 dBμV/m
• 216 – 1000 MHz: 46 dBμV/m

Bandwidth of EMI receiver: 120 kHz

Measurement Time: 1 s

Kind of Test Site: Semi-anechoic chamber

Input Voltage: AC 120 V, 60 Hz

Operational Modes Tested: Mode 1 (Warm max), Mode 2 (Warm min), Mode 3 (White max), Mode 4 (White min).

Ambient Condition: Temperature: 19.2 °C; Relative humidity: 51.3 %

Expanded Measurement Uncertainty (k=2): 5.40 dB

The minimum margin to the limit was 10.1 dB at 33.758750 MHz. The margin is higher than the expanded measurement uncertainty.

The test was performed in a semi-anechoic chamber at a distance of 3m. The EUT was placed on an 80 cm wooden support, rotated 360°, and the antenna height was varied from 1m to 4m. Tests were conducted with the antenna in horizontal and vertical polarizations.

Figure 9: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Horizontal polarization, Mode 1

Figure 10: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Vertical polarization, Mode 1

Figure 11: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Horizontal polarization, Mode 2

Figure 12: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Vertical polarization, Mode 2

Figure 13: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Horizontal polarization, Mode 3

Figure 14: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Vertical polarization, Mode 3

Figure 15: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Horizontal polarization, Mode 4

Figure 16: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Vertical polarization, Mode 4

Radiated Emission (1-18 GHz)

Result: Passed

Date of Testing: 2025-04-10

Port: Enclosure

Test Procedure: FCC 47 CFR Part 15, Subpart B:2023, ICES-005:2018, ICES-003:2020, ANSI C63.4-2014 and CISPR 16-2-3

Product Classification: Class B

Limits (3 m distance):

• Peak limits: 1–18 GHz, 74 dBμV/m
• Average limits: 1–18 GHz, 54 dBμV/m

Frequency Range: 1 – 18 GHz

Kind of Test Site: Absorber-lined semi-anechoic chamber

Test Distance: 3 m

Test Voltage: AC 120 V, 60 Hz

Operational Modes Tested: Mode 1 (Warm max), Mode 2 (Warm min), Mode 3 (White max), Mode 4 (White min).

Ambient Condition: Temperature: 19.2 °C; Relative humidity: 51.3 %

Expanded Measurement Uncertainty (k=2): 5.17 dB (1 GHz~6 GHz), 5.12 dB (6 GHz~18 GHz)

The minimum margin to the limit was 15.6 dB at 4952.500000 MHz. The margin is higher than the expanded measurement uncertainty.

The test was performed in an absorber-lined semi-anechoic chamber at 3m distance. The EUT was placed on an 80 cm supporting table, rotated 360°, and the antenna height was varied from 1m to 4m. Tests were conducted with the antenna in horizontal and vertical polarizations.

Figure 17: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Horizontal polarization on mode 1

Figure 18: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Vertical polarization on mode 1

Figure 19: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Horizontal polarization on mode 2

Figure 20: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Vertical polarization on mode 2

Figure 21: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Horizontal polarization on mode 3

Figure 22: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Vertical polarization on mode 3

Figure 23: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Horizontal polarization on mode 4

Figure 24: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Vertical polarization on mode 4

Photographs of the Test Set-Up

Refer to the test setup file.

List of Test and Measurement Instruments

List of Figures

Figure 1: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, L, Mode 1

Figure 2: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, N, Mode 1

Figure 3: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, L, Mode 2

Figure 4: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, N, Mode 2

Figure 5: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, L, Mode 3

Figure 6: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, N, Mode 3

Figure 7: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, L, Mode 4

Figure 8: Spectral Diagrams, Conducted Emission, 150 kHz – 30 MHz, N, Mode 4

Figure 9: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Horizontal polarization, Mode 1

Figure 10: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Vertical polarization, Mode 1

Figure 11: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Horizontal polarization, Mode 2

Figure 12: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Vertical polarization, Mode 2

Figure 13: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Horizontal polarization, Mode 3

Figure 14: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Vertical polarization, Mode 3

Figure 15: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Horizontal polarization, Mode 4

Figure 16: Spectral Diagrams, Radiated Emission, 30 MHz – 1000 MHz, Vertical polarization, Mode 4

Figure 17: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Horizontal polarization on mode 1

Figure 18: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Vertical polarization on mode 1

Figure 19: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Horizontal polarization on mode 2

Figure 20: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Vertical polarization on mode 2

Figure 21: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Horizontal polarization on mode 3

Figure 22: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Vertical polarization on mode 3

Figure 23: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Horizontal polarization on mode 4

Figure 24: Spectral Diagrams, Radiated Emission, 1 GHz – 18 GHz, Vertical polarization on mode 4

End of test report