ASBS Mini PC User Manual

Product Interface Description

The Mini PC features the following ports:

• 1. TYPE-C
• 2. USB 3.0 x 2
• 3. Audio Jack
• 4. Power button
• 5. RJ45 Network
• 6. DC19V
• 7. DP Port
• 8. HDMI Port
• 9. USB 3.0 x 2

Quick Installation

To set up your Mini PC, follow these connection steps:

• Connect the display device via HDMI, DP, or TYPE-C line.
• Connect the power supply using the provided DC adapter.
• Connect your keyboard and mouse via the USB interface.
• Connect to the internet using a network cable or WIFI. Note: WIFI setup is required after powering on the device.

Diagrams in the original document illustrate these connections, showing the Mini PC unit and its ports connected to a display, power adapter, input devices, and network.

Upgrading Memory and Replacing Hard Drive

Preparation for Upgrade

• A. Switch off all peripheral devices connected to the Mini PC.
• B. Turn off the Mini PC and disconnect the power cord.
• C. Open the top magnetic cover.

1. Replacing Memory

To upgrade the memory, select a memory module that meets the following requirements: DDR4: 2133/2400/3200MHz SO-DIMM. If installing only one memory module, please install it in the lower memory slot.

The process involves gently unfolding metal retaining clips on each end of the memory slot to allow the module to pop out. Hold the module by its edges and remove it from the socket. To install a new module, align its notch with the protrusion on the slot holder, insert the bottom edge at a 45-degree angle, and push down on the outer edge until the retaining clip snaps into place. Ensure the clips are securely fastened.

2. Replace or Install M.2 SSD

Remove the pre-installed SSD memory from the connector counterclockwise using a screwdriver. Align the notch on the bottom of the new M.2 SSD with the tab on the connector, then insert the bottom edge of the M.2 SSD into the connector. Finally, use a screwdriver clockwise to secure the M.2 SSD to the bracket with screws.

(Note: Installation of a new SSD requires system re-installation. Please contact customer support for assistance.)

Diagrams in the original document visually guide these steps, showing the removal of the old SSD, alignment of the new SSD with the connector, and securing it with screws.

Installation of VESA Bracket

Follow these instructions to install and use the VESA mounting bracket:

1. Fix the two brass screws (A) included in the box into the corresponding screw holes on the back of the mini PC.
2. Using the four small black screws included in the box, attach the VESA bracket to the back of the monitor or TV.
3. Fix the mini PC through the two screws (A) attached to the bottom of the main unit, slipping it over the VESA mounting bracket hole (B) to complete the installation.

Diagrams in the original document illustrate the attachment of the VESA bracket to the Mini PC and a monitor or TV.

Precautions

• Be extremely careful when performing operations that may cause file damage or loss.
• Pay attention to virus protection; try to use a virus firewall during the use of this Mini PC.
• If you do not use the device for a long time, please turn it off and disconnect the power.
• Do not turn the device on and off frequently in a short period. It is recommended that the interval between two boots should be at least 10 seconds, preferably no less than 60 seconds.
• Pay attention to moisture; keep the use environment clean and sanitary. If there is dust on the device, please wipe it with a dry soft cloth.
• Avoid direct exposure of the device to strong light and stay away from strong magnetic fields.
• Do not get water, food, or other fluids onto the device, and do not pull the data and power lines forcefully.

Packing List

• Mini PC x 1
• User Manual x 1
• Power Adapter x 1
• HDMI Cable x 1
• Mini PC copper fixing screws x 2
• Hard disk fixing screws x 4
• VESA Mounting Bracket x 1
• VESA Mounting Bracket Screws x 4

Disclaimer

• Please use the original power supply. ASBS cannot be held responsible for any problems or failures caused by any third-party adapters.
• Users may use music videos, images, and software provided by third parties, but ASBS cannot be held responsible for copyright issues or software failures.
• If the product fails, ASBS will strictly abide by the warranty terms but will not be held responsible for any property damage or financial loss that may be caused during use.
• The equipment comes with built-in software at the factory, which can be used after actual testing. However, its removal will not affect the machine in any way regarding compatibility or other issues. Please note that this is not a product quality issue.
• The company reserves the right to make improvements to its products, and product specifications and designs are subject to change without notice. Please refer to the actual product.

ASBS Customer Service

Phone: +1 833 536 1076 (Mon-Fri 9:00am~5:00pm EST)

Email: support_asbsdirect@163.com