Installation Guide for FORTIN models including: 89171 1999 Mazda B-Series Regular Key Remote Starters and Alarm Systems, 89171, 1999 Mazda B-Series Regular Key Remote Starters and Alarm Systems, Regular Key Remote Starters and Alarm Systems, Remote Starters and Alarm Systems, Alarm Systems

Installation régulière pour transmission automatique seulement #89171

Démarreurs à distance Mazda B-Series 1999 clé-régulière et systèmes d’alarme | Fortin Systèmes Électroniques

EVO-ONE & MAZDA B-SERIES (1999-2000)

EVO-ONE | All-In-One Remote Starter, Alarm, Immobilizer Bypass and Data Interface Module. | Fortin Electronic Systems


File Info : application/pdf, 5 Pages, 1.45MB

PDF preview unavailable. Download the PDF instead.

EVO-ONE IG REG BI MAZ-BSERIES 1999-2000 A 89171
ONE Page 1 / 5
REGULAR INSTALLATION INSTALLATION RÉGULIÈRE

REV.: 20220114

Guide # 89171

ADDENDUM - SUGGESTED WIRING CONFIGURATION ADDENDA - SCHÉMA DE BRANCHEMENT SUGGÉRÉ

Vehicle functions supported in this diagram (functional if equipped) | Fonctions du véhicule supportées dans ce diagramme (fonctionnelles si équipé)

Immobilizer bypass Contournement d'immobilisateur Lock Unlock Parking Light Foot-Brake Status

VEHICLE VEHICULES MAZDA
B-Serie

YEARS ANNÉES
1999-2000

·

·

·

·

·

BYPASS FIRMWARE VERSION VERSION LOGICIELLE CONTOURNEMENT
71.[44]
MINIMUM

To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool,
sold separately.
Pour ajouter la version logicielle et les options, utilisez l'outil FLASH LINK UPDATER
ou FLASH LINK MOBILE, vendu séparément.

Program bypass option IF THE VEHICLE IS NOT EQUIPPED
WITH FUNCTIONAL HOOD PIN:
Programmez l'option du contournement SI LE VÉHICULE N'EST PAS ÉQUIPÉ
D'UN CONTACT DE CAPOT FONCTIONNEL:

UNIT OPTION OPTION UNITE

A11

OFF NON

DESCRIPTION
Hood trigger (Output Status). Contact de capot (état de sortie).

Program remote starter option:
Programmez l'option démarreur à distance:

FUNCTION FONCTION
2
20

MODE
2 2

DESCRIPTION
(+) Accessory 2 (E1) (+) Accessoire 2 (E1)
Tachless only. ( vehicles with automatic transmission only) Sans Tachymètre seulement. (véhicules à transmission automatique seulement)

MANDATORY INSTALL | INSTALLATION OBLIGATOIRE

* HOOD PIN
CONTACT DE CAPOT

HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED) MUST BE INSTALLED IF THE VEHICLE CAN BE

A11

OFF NON

REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.

STATUT DE CAPOT : LE CONTACT DE CAPOT (INCLUS), DOIT ÊTRE INSTALLÉ SI LE VÉHICULE PEUT DÉMARRER À DISTANCE, LORSQUE LE CAPOT EST OUVERT, PROGRAMMEZ LA FONCTION A11 À NON.

SECURITY STICKER
AUTOCOLLANT DE SÉCURITÉ

WARNING ATTENTION

Included Inclus

Notice: the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed. Notice: l'installation des éléments de sécurité est obligatoire. Le contact de capot et l'autocollant de sécurité sont des éléments de sécurité essentiels et doivent absolument être installés.

THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG
CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
CE MODULE DOIT ÊTRE INSTALLÉ PAR UN TECHNICIEN QUALIFIÉ, TOUTE
ERREUR DANS LES BRANCHEMENTS PEUT OCCASIONNER DES DOMMAGES
PERMANENTS AU VÉHICULE.

This guide may change without notice. See www.fortin.ca for latest version. Ce guide peut faire l'objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
WIRING CONNECTION | GUIDE DE BRANCHEMENTS

HOOD PIN MANDATORY CONTACT CAPOT OBLIGATOIRE

Yellow In AA11

(-)Lock

Purple Out AA22

(-)Unlock Purple/White Out AA33

Green Out AA44

White Out AA55

Orange Out AA66

(-)Horn Orange/Black Out AA77

Dk.Blue Out AA88

Red/Blue In AA99

(~) RX Lt.Blue/Black In/Out AA1100

(+)Foot Brake

Black In AA1111

(-)Parking Lights

Pink Out AA1122

Yellow/Black Out AA1133

Brown/White In AA1144

(-)Hood Pink/Black In AA1155

Purple/Yellow In/Out AA1166

Green/White In/Out AA1177

Green/Red In/Out AA1188

White/Black Out AA1199

(~) TX

Lt.Blue In/Out AA2200

(+)Accessory2
(+)Accessory
(+)12V
(-)Ground (+)Ignition (+)Starter

White Out EE11 Orange Out EE22
Red In EE33 Black In EE44 Pink In/Out EE55 Yellow Out EE66

CUT LOOP FOR AUTOMATIC TRANSMISSION MODE. COUPEZ LA BOUCLE POUR LE MODE TRANSMISSION AUTOMATIQUE.
C5 Brown C4 Gray/Black C3 Gray C2 Orange/Brown C1 Orange/Green D6 White/Red D5 White/Blue D4 White/Green D3 Yellow/Red D2 Yellow/Blue D1 Yellow/Green

Ground Masse

A7 (-)HORN
Yellow/Lt.Green Jaune/Vert Pâle

OPTIONAL FACULTATIF
6
Steering Column. Colonne de direction.

Page 2 / 5

B-SERIES

Fuse Fusible

A11

A3

A2

A20

(+)BRAKE (-) UNLOCK (-) LOCK TX

A10

A12

E2

E1

E6

E5

E3

RX

(-)PARKING (+) ACCES- (+) ACCES-

LIGHTS

SORY

SORY2

(+)START

(+) IGNITION

(+)12V

Green Vert

Pink/Lt. Green Pink/Yellow White/Lt.Green Grey/Orange White/Violet Grey/Yellow Black/Lt. Green Red/Lt. Blue

Lt. Green/Purple Yellow

Rose/Vert Pâle Rose/Jaune Blanc/Vert Pâle Gris/Orange Blanc/Mauve Gris/Jaune Noir/Vert Pâle Rouge/Bleu Pâle Vert Pâle/Mauve Jaune

4
At Brake switch Transponder connector
(5-pins) Back view Au commutateur des
freins connecteur du transpondeur. Connecteur (5-pins)
Vue de dos

5
Driver kick panel
Panneau latéral côté connducteur

4321
2
At ignition barrel Transponder connector
White connector (4-pins) Back view Au barillet d'ignition
connecteur du transpondeur. Connecteur Blanc (4-pins) Vue de dos

3
Driver kick panel Panneau latéral côté
connducteur

1
At ignition barrel Transponder connector
(15-pins) Back view Au barillet d'ignition
connecteur du transpondeur. (15-pins)
Vue de dos

26 1 4
3 5

This guide may change without notice. See www.fortin.ca for latest version. Ce guide peut faire l'objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
1 KEY PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION AVEC 1 CLÉ

Page 3 / 5

1
x1
HOLD
2
RELEASE
3

G F A

J H B C D

J

I

I

G F A

H B C D

E

LED may differ depending on the module casing. L'apparence des DELS peut différer selon le boîtier du module.
RED ON
ROUGE

Press and hold the programming button: Insert the 6-Pin Main connector.
9 The LEDs will alternate between BLUE, RED, YELLOW & BLUE/RED flashes.

Appuyez et maintenir le bouton de programmation
enfoncé: Insérez le connecteur
Principal à 6-broches.
9 Les DELS alterneront entre un clignotement BLEU, ROUGE, JAUNE & BLEU/ROUGE.

Release the programming button when the LED is RED.

Relâchez le bouton de programmation quand la DEL est ROUGE.

If the LED is not solid RED disconnect the 6 Pin connector (Main-Harness) and go back to step 1.

Si le DEL n'est pas ROUGE solide débranchez le connecteur 6 pins (Connecteur principal) et allez à l'étape 1.

H B C D

J

E

G F A

D E

H B C

I

J

J H B C D

Insert the required remaining Insérez les connecteurs requis

connectors.

restants.

J H B C D

J H B C D

I I

LOCK E

G F A

G F A E

G F A E

G F A E

I I

I START

4
TURN ON/RUN
KEY#1
5
TURN OFF
6
TURN ON/RUN
KEY#1
7
TURN OFF
8

LOCK

LOCK

LOCK LOCK

ACC ON

IGN

PUSH

WAIT 3 SEC.

LOCK

START

IGN ON
ACC ON

START

OFF
ACC ON PUSH

REMOVE KEY
ACC ON
PUSH

START

Turn the functIonal key to the ON/RUN position.
Wait 3 seconds.

Tournez la clé fonctionnelle à la position ON/RUN.
Attendre 3 secondes.

Turn the ignition to the OFF position
and remove the first key.

Tournez la clé à la position ARRÊT (OFF)
et retirez la clé du barillet.

ACC ON

IGN

START

PUSH

Turn the functIonal key to the ON/RUN position.

Tournez la clé fonctionnelle à la position ON/RUN.

I START

OFF
ACC ON PUSH

G J
F

A

H

B

C E
D

REMOVE KEY
ACC ON
PUSH

LOCK

START

Turn the ignition to the OFF position
and remove the first key.

Tournez la clé à la position ARRÊT (OFF)
et retirez la clé du barillet.

KEY OFF

FLASH 10X

FLASH 10X

OFF

The RED LED will flash rapidly ten (10) times.
If the LED is solid RED disconnect the 6 Pin connector (Main-Harness) and go back to step 1.

La DEL ROUGE clignotera dix (10) fois rapidement.
Si le DEL est ROUGE solide débranchez le connecteur 6 pins (Connecteur principal) et allez à l'étape 1.

H B C D

J

E

G F A

The module is now
programmed.
Use the remote of the remote starter or security system to test all of the supported features to ensure proper programming.

Le module est
programmé.
Testez toutes les fonctions supportées sur le véhicule avec la télécommande du démarreur à distance ou du système de sécurité.

This guide may change without notice. See www.fortin.ca for latest version. Ce guide peut faire l'objet de changement sans préavis. Voir www.fortin.ca pour la récente version.

Page 4 / 5

REMOTE STARTER PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION DU DÉMARREUR À DISTANCE

REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.
RÉFÉREZ-VOUS AU GUIDE D'INSTALLATION RAPIDE INCLUS AVEC LE MODULE POUR LA PROGRAMMATION DU DÉMARREUR À DISTANCE.

REMOTE STARTER FUNCTIONALITY | FONCTIONNALITÉS DU DÉMARREUR À DISTANCE

Start

UNLOCK

TURN ON/RUN

ON

All doors must be closed. Toutes les
portes doivent être fermées.

Remote start the vehicle.
Démarrez à distance.

Unlock the doors with the remote-starter remote or the OEM remote.
Déverrouillez les portes avec la télécomande du démarreur à distance ou
la télécommande d'origine.

Insert and Turn the key to the Ignition ON/RUN
position. Insérez et tournez la clé à la position "ON/RUN".

Press the brake pedal.
Appuyez sur la pédale de
frein.

The vehicle can now be put in to gear and driven.
Vous êtes maintenant prêt à
embrayer et prendre la route.

Page 5 / 5

ONE

HARDWARE VERSION FIRMWARE VERSION
Date: xx-xx
INTERFACE MODULE
PATENTS PENDING US: 2007-228827-A1
Made in Canada www.fortinbypass.com
Service No : 000 102 04 2536
Module label | Étiquette sur le module

Notice: Updated Firmware and Installation Guides Updated firmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product.
Notice: Mise à jour microprogramme et Guides d'installations Des mises à jour du Firmware (microprogramme) et des guides d'installation sont mis en ligne régulièrement. Vérifiez que vous avez bien la dernière version logiciel et le dernier guide d'installation avant l'installation de ce produit.

WARNING The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualified technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.
MISE EN GARDE L'information de ce guide est fournie sur la base de représentation (telle quelle) sans aucune garantie de précision et d'exactitude. Il est de la seule responsabilité de l'installateur de vérifier tous les fils et circuits avant d'effectuer les connexions. Seuls une sonde logique ou un multimètre digital doivent être utilisés. FORTIN SYSTÈMES ÉLECTRONIQUES n'assume aucune responsabilité de l'exactitude de l'information fournie. L'installation (dans chaque cas) est la responsabilité de l'installateur effectuant le travail. FORTIN SYSTÈMES ÉLECTRONIQUES n'assume aucune responsabilité suite à l'installation, que celle-ci soit bonne, mauvaise ou de n'importe autre type. Ni le manufacturier, ni le distributeur ne se considèrent responsables des dommages causés ou ayant pu être causés, indirectement ou directement, par ce module, excepté le remplacement de ce module en cas de défectuosité de fabrication. Ce module doit être installé par un technicien qualifié. L'information fournie dans ce guide est une suggestion. Ce guide d'instruction peut faire l'objet de changement sans préavis. Consultez le www.fortinbypass.com pour voir la plus récente version.
Copyright © 2006-2018, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING

TECH SUPPORT Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE

www.fortinbypass.com
WEB UPDATE | MISE À JOUR INTERNET



References

Adobe PDF Library 16.0 Adobe InDesign 16.4 (Windows)