Safety Instructions
⚠ CAUTION: RISK OF FIRE !
WARNING! To prevent any damages to your and others' life or property, you have to follow the safety notes.
Intended Use
- This heat pump dryer is intended for drying typical amounts of household laundry, which have been washed with water. It has been designed solely for private use and is not suitable for commercial or shared use (i.e. by several families in an apartment building).
- Use this appliance only as described in this user manual.
- This appliance is for indoor use only.
- Any other use is deemed improper and may result in damage to property or even personal injury.
- The manufacturer accepts no liability for damage caused by improper use.
Electrical Safety
- The appliance corresponds to protection class I and may only be connected to a plug with a protective conductor that has been installed properly. When connecting the appliance to the mains, make sure that the mains voltage is correct. You can find more information about this on the rating plate.
- WARNING! Electric shock hazard
- Before connecting the tumble dryer, ensure that the connection parameter on the rating plate (fuse rating, voltage and frequency) match the mains electricity supply. If in any doubt, consult a qualified electrician.
- The electrical safety of this tumble dryer can only be guaranteed when correctly earthed. It is essential that this standard safety requirement is met. If in any doubt, please have the household wiring system tested by a qualified electrician. The manufacturer cannot be held liable for the consequences of an inadequate earthing system (e.g. electric shock).
- Do not pull the power cord forcefully. Please grasp the mains plug instead.
- Do not plug/draw the mains plug with wet hands.
- Do not bend, clamp or damage the power cord and the power plug.
- If the power cable is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
- The appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by a utility.
- Do not connect the appliance to the mains electricity supply by an extension lead, multi-socket adapter or similar.
- The accessibility of the plug must always be ensured, in order to disconnect the tumble dryer from the mains.
- If the appliance appears high temperature abnormally, please draw the mains plug immediately.
Installation & Usage Safety
- WARNING! Injury danger
- The appliance must not be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the tumble dryer, in such a way that a full opening of the tumble dryer door is restricted.
- Do not disassemble or install the dryer without any instruction or supervision.
- Do not stack this dryer on a washing machine without stacking kits. (If you want to stack this dryer on a washing machine, please purchase the independent parts. Installation shall be done by the manufacturer, its service agent or similarly qualified persons to avoid any hazards.)
- Do not lean on the opened door of the dryer.
- Condensed water is not drinking water. It can cause health problems in both people and animals if consumed.
- WARNING! Damage danger
- Do not put more load than rated in this user manual. See the related chapter in the user manual.
- Do not operate the dryer without the door filter.
- Do not dry the clothes before being spun.
- Do not expose the dryer directly under the sun.
- Do not install the dryer in a humid and drenching environment.
- While cleaning and maintenance, please do remember to pull out the power plug and do not directly spray the dryer with water.
- The appliance should not be overturned during normal use or maintenance.
Fire & Explosion Safety
⚠ CAUTION: RISK OF FIRE !
Explosion & Fire danger
- Please do not dry the clothes with any flammable substances such as kerosene or alcohol. Otherwise, there may be explosion.
- The appliance contains an environmentally friendly but flammable R290 refrigerant. Keep away from open flame and other sources of ignition.
- The tumble dryer is not to be used if industrial chemicals have been used for cleaning.
- Do not dry unwashed items in the tumble dryer.
- Items that have been soiled with substances such as cooking oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes and wax removers should be washed in hot water with an extra amount of detergent before being dried in the tumble dryer.
- Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the tumble dryer.
- Fabric softeners, or similar products, should be used as specified by the fabric softener instructions.
- Oil-affected items can ignite spontaneously, especially when exposed to heat sources such as in a tumble dryer. The items become warm, causing an oxidation reaction in the oil. Oxidation creates heat. If the heat cannot escape, the items can become hot enough to catch fire. Piling, stacking or storing oil-affected items can prevent heat from escaping and so create a fire hazard.
- Remove all objects from pockets such as lighters and matches.
- If it is unavoidable that fabrics that contain vegetable or cooking oil or have been contaminated by hair care products be placed in a tumble dryer they should first be washed in hot water with extra detergent. This will reduce, but not eliminate the hazard.
- WARNING: Never stop a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.
- Openings must not be obstructed.
- The lint trap has to be cleaned frequently.
- Lint must not to be allowed to accumulate around the tumble dryer.
- Do not damage the refrigerant circuit.
Safety with Children
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be done by children without supervision.
- Children should be supervised to ensure that they do not play with the appliance.
- Children of less than 3 years should be kept away unless continuously supervised.
- Always close the door after use. In this way you will avoid the danger of: 1. Children climbing onto or into the dryer or hiding things in it. 2. Pets or other small animals climbing into it.
UV Radiation Safety
- This warning only covers products which contain a UV-C lamp and which have a germs reduction function with UV-C lamp.
- The device contains a lamp that emits UV-C rays. Do not look at the source of light while the lamp is operating!
- UV-C Lamp is used to provide germs reduction in textile products.
- Do not take the UV-C Lamp out of the device and do not operate it outside!
- Do not touch the lamp!
- Use of the product except for its purpose or damage to the UV-C lamp protection glass or surrounding may cause dangerous UV-C radiation to occur. UV-C radiation can damage the eyes and skin even in low doses. Do not operate any product which is damaged!
- Do not remove the UV-C lamp protection glass. Do not operate the product without the UV-C lamp protection glass!
- After the stops due to various reasons (power outage, fuse problem, machine door opening, etc.) while UV Hygiene Programs are in progress, the program will resume to germs reduction from where it left.
- In cases where UV-C lamp and related parts need to be replaced (expiration of lamp life, break of lamp glass, etc.), call the technical service. Do not try to replace the parts by yourself. When waiting for technical service, make sure the machine cover is closed and the plug is disconnected!
- Keep children away while using any programmes with activated UV-C Lamp!
- Always read the product guide before using the device and use the product according to the instructions!
- The placement of the UV Lamp and lamp protector glass in your product is visually indicated.
- Hygiene programme incorporating UV is effective for removing Escherichia coli, Staphylococcus aureus bacteria.
Correct Disposal
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
Disposal of packaging material
The packaging is designed to protect the appliance from damage during transportation. The packaging materials are environmentally friendly and should be recycled. Recycling the packaging can reduce the use of raw materials in the manufacturing process and the amount of waste in landfill sites.
Model | Rated capacity |
---|---|
MD200H80WB/W-AU | 8.0kg |
Installation
Product Description
The tumble dryer consists of the following main parts:
- Power cord: Connects the appliance to the electrical supply.
- Top board: The upper surface of the dryer.
- Water container: Collects condensed water.
- Drum: Where the laundry is placed for drying.
- Door filter: Filters lint from the air.
- Control panel: Interface for operating the dryer.
- Door: Access to the drum.
- Maintenance cover: Provides access to internal components for maintenance.
Note! The product picture is for illustration only, please refer to real product as reference.
Accessories
The following parts may be optional for specific models. If your dryer includes these parts, please wear gloves to install them as per the instructions:
- Hose holder
- Condensing drain hose
- Connector
Installation Steps
- Drain Hose Connection: Pull out the upper drain hose. Put the external drain hose into the floor drain, ensuring it is not kinked.
- Alternative Drainage: Place the hose holder in a washing basin or any other sink.
Transport
Move cautiously. Do not grasp any salient parts of the machine. The machine door cannot be used as the handle for transport. If the dryer cannot be transported upright, it can be tilted to the right by less than 30 degrees.
⚠ Risk of injury and damage! Improper handling of the appliance may result in injury.
- The appliance is very heavy. Never transport or carry the appliance alone; always with the assistance of another person.
- Remove all obstacles on the transport route and from the installation location, e.g., open doors and clear away objects lying on the floor.
- Do not use the open door as a handhold.
- Remove all package material before using the appliance.
- Before setting up the tumble dryer, check it for any externally visible damage. Do not install or use a damaged tumble dryer.
- Do not install the tumble dryer in a room where there is a risk of frost occurring. At temperatures around freezing point, the tumble dryer may not be able to operate properly. There is a risk of damage if the condensed water is allowed to freeze in the pump and hoses.
Installation Position
⚠ WARNING!
- Children can become entangled in the packaging film or swallow small parts and suffocate. Do not allow children to play with the packaging.
- The appliance must not be installed behind a lockable door, a sliding door, or a door with a hinge on the opposite side to that of the tumble dryer, in such a way that a full opening of the tumble dryer door is restricted.
- Do not restrict the floor clearance through deep pile carpets, strips of wood, or similar. This might cause heat built-up which would interfere with the operation of the appliance.
- It is recommended that, for your convenience, the machine is positioned close to your washing machine.
- Do not stack this dryer on a washing machine without stacking kits. Installation shall be done by the manufacturer, its service agent, or similarly qualified persons to avoid any hazards.
- The tumble dryer must be installed in a clean place, where dirt does not accumulate. Air must be able to circulate freely around the appliance. Do not obstruct the front air inlet or the air intake grilles at the back of the machine.
Level Adjusting
To keep vibration and noise within a minimum level when the dryer is in use, it must be placed on a firm and level surface. The feet must never be removed.
Once in its permanent operating position, check that the dryer is absolutely level with the aid of a spirit level. If it is not, adjust the feet by hand or using a tool.
Power Supply Connection
- Make sure that the voltage of the power supply is the same as the electric specification.
- Do not connect the dryer with a power connection board, a universal plug or socket; do not use multi-plug adapters and extension cables.
Note!
- Leave the appliance to stand for 2 hours after transporting. Before first use, please use a soft fabric to clean the inside drum.
- Put some clean rags into the drum.
- Plug in the power, press the [On/Off] button.
- Select the [Refresh] Programme, press the [Start/Pause] button.
- After finishing this programme, please follow the "Cleaning and Care" (refer to page 27) to clean the door filter.
- During drying, the compressor and the water will generate some noise, which is entirely normal.
Operation
Quick Start
Note! Before using, make sure the tumble dryer is installed correctly.
Before Drying
Follow these steps before loading laundry:
- Plug in the appliance.
- Load the laundry into the drum.
- Close the door securely.
Drying Process
Select the desired program and start the cycle:
- Press the [On/Off] button to power on.
- Select the program using the program selector knob.
- Select function or default settings as needed.
- Press the [Start/Pause] button to begin the drying cycle.
After Drying
Once the cycle is complete, the buzzer will beep and "End" will display:
- Open the door and take out the laundry.
- Pull out the water container.
- Pour out the condensate water into a basin.
- Clean the filter.
- Turn off the appliance by pressing the [Power Off] button.
Note! If the socket has a switch, please press the switch to turn off the power directly.
Before Each Drying
- Before drying, thoroughly spin the laundry in the washing machine. High spin speed shortens the drying time and saves energy.
- For uniform drying results, sort the laundry according to fabric type and select the appropriate drying program.
- Before drying, please close zips, hooks, eyelets, buttons, and tie fabric belts, etc.
- Remove all objects from pockets such as lighters and matches.
- Sew in or remove underwiring from bras.
- Close duvet covers and pillow cases to prevent small items from being rolled up inside them.
- Leave jackets open and undo any long zips so that textiles dry evenly.
- Do not over-dry the clothes, as over-dried clothes can easily get creases.
- Do not dry articles containing rubber or similar elastic materials.
- Keep the area around the tumble dryer clean. Coal dust or flour may cause an explosion.
- The door shall be opened only after the program of the tumble dryer is finished to avoid being scalded by hot steam or the heated drying machine.
- Clean the lint filter and empty the water container after each use to avoid extension of drying time and increase of energy consumption.
- Do not dry clothes after a dry-clean process.
Reference Weights of Dry Clothes (Weight per Item)
This table provides reference weights for common clothing items:
- Sweater (mixed): 800g
- Jacket (cotton): 800g
- Jeans: 800g
- Bath Towel (cotton): 900g
- Single bedsheet (cotton): 600g
- Work clothes: 1120g
- Pyjamas: 200g
- Shirt (cotton): 300g
- T-Shirt (cotton): 180g
- Underwear (cotton): 70g
- Socks (mixed-weave): 50g
Note!
- Do not put more load than rated.
- Do not dry dripping wet laundry, as the dryer might get damaged.
Laundry Care Labels
Only dry laundry suitable for tumble drying. Regard the laundry care labels:
- Suitable for tumble drying: Normal drying process: Drying in the tumbler is possible under normal load and temperature 80°C.
- Mild drying process: Caution is appropriate when tumble drying. Select mild process with reduced thermal action.
- Do not tumble dry: Articles unsuitable for drying in the tumbler.
Control Panel
The control panel allows you to operate the dryer:
- 1. On/Off: Powers the product on or off.
- 2. Start/Pause: Press to start or pause the drying cycle.
- 3. Option Buttons: Used for setting additional functions like Delay, Time, Intensity, etc.
- 4. Display: Shows the setting, estimated program time remaining, and status messages.
- 5. Programmes: Select different drying cycles according to user needs and laundry type.
Programmes and Options
Delay
This function delays the start of the drying program up to 24 hours. When the delayed program starts, the time begins to countdown on the display, and the delay icon illuminates.
- Load laundry and ensure the machine door is closed.
- Press the [On/Off] button, then use the program selector knob to select the desired program.
- Optionally, select [Anti-Crease] or [Signal] functions.
- Press the [Delay] button.
- Repeatedly press the [Delay] button to select the desired delay time.
- After pressing [Start/Pause], the dryer will run. The drying procedure will start automatically when the delay time is over.
- Pressing [Start/Pause] again will pause the delay function.
- To cancel the "Delay" function, press the [On/Off] button.
Time
When [Time Dry], [Airfresh], or [Warm] programs are selected, the [Time+] and [Time-] buttons can be used to adjust the drying time in 10-minute steps.
Intensity
Adjust the dryness level of the laundry by pressing the [Intensity] button. This function can be adjusted only before the program starts. Pressing [Intensity] repeatedly increases the drying grade. This function is available for most programs except [1 Shirt], [Bed Linen], [Cotton], and [Iron].
Lamp
The drum light turns on for 1 minute when the button is pressed or when the door is open.
Signal
Set the buzzer on or off. By default, the buzzer is on. When the buzzer is on:
- The dryer will confirm pressed function buttons with a sound.
- If the program knob is rotated during drying, the buzzer will alert the user of an invalid operation.
- When the drying program is done, the buzzer will beep.
Anti-Crease
At the end of the drying cycle, the anti-crease time is 30 minutes (default) or 120 minutes (selected). This function prevents laundry from creasing. Laundry can be removed during the anti-crease phase. This function is available for all programs except [Wool], [Airfresh], and [Time Dry].
Child Lock
This feature prevents children from accidentally pressing buttons or causing faulty operations.
- When the dryer is running or paused, press the [Child Lock] button simultaneously for 3 seconds to activate child lock.
- When child lock is active, the display will show a Child Lock icon, and all buttons will be deactivated except [On/Off] and [Lamp].
- To deactivate child lock, press the [Child Lock] button simultaneously for 3 seconds.
Wireless Network & Remote Control
To activate the wireless network function and connect your appliance to the internet, press the [Wireless Network] button for 3 seconds. For details on first installation, refer to the App setup section (page 24).
After connecting your device to the wireless network, press the [Remote Control] button for 3 seconds to activate remote control state and control your appliance via smartphone. Smartphone remote control requires:
- Wireless network activated and the appliance connected to the internet.
- The appliance door is closed.
Note: If the door is opened at any time, the remote control function will be disabled. The remote control function turns off automatically at the end of each cycle; to use it again, you need to turn it on again.
UV Hygiene
After selecting a program, you can choose the [UV Hygiene] function. Pressing it again cancels the function. This function removes germs during the drying process, making clothes cleaner and safer. Use with caution for light, thin, or delicate laundry. Programs like [Outdoor], [Bed Linen], [1 Shirt], [5 Shirts], [Baby Care], [Mix], [Towel], [Jeans], [Cupboard], [Extra], [ECO], and [Bulky Dry] have UV function activated. You can deactivate the UV function for these programs by pressing the [Lamp] button for 3 seconds.
Airfresh
- To refresh your laundry using cold air.
- Select any program and press the [Airfresh] button.
- The program time will change to 20 minutes and will be indicated on the display.
- Press [Airfresh] again to deactivate and return to the selected program.
Display Icons
The display shows various indicators:
- Delay: Indicates the delay start function is active.
- Child Lock: Indicates the child lock is activated.
- 18:88: Remaining Time indicator/Error message.
- Filter Icon: Clean filters warning.
- Water Container Icon: Empty water container warning.
- Sun/Snowflake Icons: Intensity levels (e.g., iron dry, cupboard dry, extra dry).
- Lamp Icon: Indicates the drum light status.
- Signal Icon: Buzzer status (on/off).
- Anti-Crease Icon: Indicates the anti-crease function is active.
- UV Icon: Indicates the UV Hygiene function is active.
- Wireless Network Icon: Indicates wireless network connection status.
- Remote Control Icon: Indicates remote control is active.
- Hygiene Icon: Indicates the hygiene program is active.
- Airfresh Icon: Indicates the Airfresh program is active.
The wool drying cycle of this machine has been tested and approved by The Woolmark Company. The cycle is suitable for drying wool garments labeled "hand wash", provided they are washed in a Woolmark endorsed hand washing cycle and dried according to the manufacturer's instructions. Model: M2132
Programmes
Before Starting the Appliance
- Insert the plug into the socket.
- Put your laundry loosely inside the drum.
- Close the door, taking care not to trap any items.
- Switch on the machine.
Programme Selector
- When the LED display screen brightens up, rotate the program knob to select the desired program.
- Select additional functions like [Time], [Anti-Crease], [Delay], [UV Hygiene], or [Intensity].
- Press the [Start/Pause] button.
- Press the [On/Off] button after the program has completed.
Programme Start
The drum will rotate after the program starts. The cycle phase LED in the display will light up, and the remaining program time will be displayed.
Programme End
- The drum will stop rotating after the program ends. The display will show "End", and the related LED will illuminate. The dryer will start the [Anti-Crease] function if the user doesn't remove the load (Refer to page 19).
- After the load is removed, press [On/Off] to switch off if the display is on. Drying is complete, please unplug.
- Deal with problems according to the "Trouble Shooting" section if there is an unexpected stop during the drying procedure or the dryer shows an Error Code (Refer to page 29).
Drying Programmes Table
Programme | Max Load | Application/Properties | Delay | Time |
---|---|---|---|---|
Extra | - | For single or multi-layer cotton laundry to be dried completely for direct storage. | Y | N |
ECO | 8.0kg | For single or multi-layer cotton laundry to be dried completely for direct wear. | Y | N |
Iron | - | For single layer cotton laundry to remain damp for ironing. | Y | N |
Mix | 3.5kg | For mixed fabrics from cotton and synthetics. | Y | N |
Extra | 3.5kg | For thick or multi-layer synthetic fabrics to be dried completely. | Y | N |
Cupboard | 3.5kg | To dry thin synthetic textiles, which are not ironed, such as easy care shirts, baby cloths or socks. | Y | N |
Wool | 1.0kg | Suitable for auxiliary drying of machine washable wool clothing. | Y | N |
1 Shirt | 0.2kg | Place clothes loosely in the dryer. Once dried, remove quickly and hang it on a clothes hanger. | Y | N |
5 Shirts | 1.0kg | Easy care laundry (small amount of thin synthetics), such as shirts and blouses equipped with anti-crease functionality to minimize the ironing effort. | Y | N |
Jeans | 4.0kg | To dry jeans or leisure clothes that are spun at high speed in the washing machine. | Y | N |
Bed Linen | 4.0kg | To dry bed linen, bed sheets or other large items. | Y | N |
Baby care | 1.0kg | To dry small amount of baby clothing. | Y | N |
Outdoor | 3.0kg | To dry outdoor clothing, waterproof and breathable laundry items which are suitable for drying in tumble dryer. | Y | N |
Time Dry | 3.0kg | To dry individual items or complete the drying of multi-layer fabrics with different drying behavior, such as jackets, pillows or voluminous items. Min 10 min. to max. 150min. (in 10 min. steps). It is recommended that the drying time of 3kg cotton and linen load is about 90 minutes. | Y | Y |
Bulky Dry | 4.0kg | To dry bed linen, bed sheets or other large items. | Y | N |
Towel * | 3.0kg | To dry thick or multi-layered cotton fabrics. | Y | N |
Warm * | - | Mainly designed for dry clothing loads, used to warm clothes. Min. 10min to max. 150min (in 10min steps). | Y | Y |
Airfresh* | 1.0kg | To refresh clothes kept at closed environment for a long time or to remove odors. Min. 20 min to max. 220 min. (in 10 min. steps). | Y | Y |
Note for Test Institutes: Extra test program in accordance with Regulation AS/NZS 2442.2 for energy labelling, measured in accordance with AS/NZS 2442.1 and suitable for drying normal cotton load at rated load capacity.
App Setup and Operation
Use Your Appliance With the SmartHome App
Before you start, ensure:
- Your smartphone is connected to your home wireless network and you know the network password.
- You are near the home appliance.
- The 2.4GHz band wireless signal is enabled on your wireless router.
Download the SmartHome App
On an app market (Google Play Store, Apple App Store), search for "SmartHome*" and find the SmartHome app. Download and install it on your phone. You can also download the app by scanning the QR code.
Register and Log In
Open the SmartHome app and create a new account to start (you can also register through a third-party account). If you already have an existing account, use that account to log in.
Connect Your Devices to SmartHome
- Please make sure your mobile phone is connected to the home wireless network. If not, go to settings and enable wireless networks and Bluetooth.
- Power on your device.
- Open the SmartHome app on your phone.
- If a message of "Smart devices discovered nearby" appears, click to add.
- If no message appears, select "+" on the page and select your device from the list of available nearby devices. If your device is not listed, please add your device manually by device category and device model.
- Connect your device to the wireless network according to instructions on the app. If the connection fails, please follow the instructions provided by the app to continue with the operation.
Start the Remote Control
Rotate the knob randomly to indicate one of the programs, and press the [Lamp/] button continuously until the remote control icon lights up in the knob display. This means it has entered the remote control state, and you can start to control remotely.
Wireless Network Status Light
Status | Meaning |
---|---|
Slowly flashing | Waiting for connection |
Quickly flashing | Connecting |
Always on | Connected to your wireless router |
NOTE
- Make sure your devices are powered on.
- Keep your mobile phone close enough to your device when connecting it to the network.
- Connect your mobile phone to the wireless network at home, and make sure you know the password of the wireless network.
- Check if your wireless router supports the 2.4 GHz band and turn it on. If you are unsure, contact the router manufacturer.
- The device cannot connect to wireless networks that require authentication (e.g., public areas like hotels). Connect to a network that does not require authentication.
- Turn off WLAN+ (Android) or WLAN Assistant (iOS) on your mobile phone when connecting the device to the network.
- If your device has connected to a wireless network before but needs to reconnect, click "+" on the app Home page and add your device again by category and model according to the app instructions.
- Max RF Output Power: Wireless Network: E.I.R.P.: 18dBm, Bluetooth LE: 8dBm. Frequency band of operation: 2400-2483.5MHz.
Maintenance
Cleaning and Care
Empty the Water Container
- Pull out and hold the water container with two hands.
- Tilt the water container and pour out the condensate water into a basin.
- Install the water container back.
⚠ WARNING!
- Empty the water container after each use. Once the water container is filled completely, the program will pause, and the "[Pause Icon]" icon will light. After emptying, the dryer can be restarted by pressing the [Start/Pause] button.
- Do not drink the condensate water.
- Do not use the dryer without the water container.
Clean the Filters
This dryer has a primary door lint filter. Make sure you clean the door filter after each cycle.
Note! To ensure the double-layer filter closes smoothly, align the arrows at both ends, and align the middle slot and the rib.
Clean the Door Filter
- Open the door.
- Take out the door filter.
- Open the filter and remove the fluff from the filter screen.
- Dry the door filter thoroughly before installing it back.
Note! Take notice of the correct orientation before inserting the door filter.
Clean the Heat Exchanger
⚠ WARNING! Do not touch the heat exchanger with your hand, which may cause an injury.
- As necessary, approximately once every 3 months, remove the fluff from the heat exchanger using a vacuum cleaner with a dusting brush attached.
- Clean the heat exchanger without applying any pressure. Otherwise, the heat exchanger could be damaged. The dryer will not dry if the cooling fins are damaged or bent.
Clean Tumble Dryer
⚠ WARNING!
- Disconnect the power cord before cleaning!
- Clean the dryer with a wet cloth that is only dampened by clean water.
- Do not use solvents, abrasive cleaners, glass cleaners, or all-purpose cleaners. These could damage plastic surfaces and other parts.
- Please wear gloves when cleaning.
- Prepare a wet cloth dampened by clean water.
- Clean the door, especially the inside window.
- Clean the sealing around the door opening.
- Clean the humidity sensor inside the drum.
- Take out the filter, clean the sealing and air flow openings.
- Before starting the dryer, dry all parts with a soft cloth.
Trouble Shooting
Many malfunctions and faults that might occur in daily operation can be easily remedied. Time and money will be saved because a service call won't be needed. The following guide may help you to find the reason for a malfunction and correct it.
Display | Reason | Solutions |
---|---|---|
Container is full | Container is full | Empty water container |
"E33" | Water pump failure or water level sensor failure | Pull out the plug from the socket. |
"E64" | Temperature sensor error | Please contact your local service center if the problem occurs. |
"E82" | BLDC motor communication error / PCB communication error | Please contact your local service center if the problem occurs. |
⚠ WARNING!
- Only authorized technicians can carry out repairs.
- If the LED displays other prompts and the dryer does not work, pull out the plug from the socket and call for service.
Note! Before you call for service, please check if you have dealt with the problems yourself by consulting the user instructions.
Problem | Solution |
---|---|
Display is not on |
|
"[Water Container Icon]" is lighting |
|
"[Filter Icon]" is lighting | Clean the lint filter. |
Dryer does not start |
|
Degree of dryness was not reached or drying time too long |
|
There are humming noises | The compressor is operating. These noises are normal and do not indicate a fault. |
The dryer switches off at the end of the program | The dryer switches off automatically for energy saving. This is not an error but a normal function. |
⚠ WARNING! If you cannot deal with the problems by yourself and need help:
- Press the [On/Off] button.
- Pull out the mains plug and call the service.
Technical Specifications
Parameter | Value |
---|---|
Model | MD200H80WB/W-AU |
Dimension (L*W*H) | 600*595*845(mm) |
Ambient temperature | +2°C ~ +35°C |
Rated input power | 750W |
Rated voltage | 220-240V~ |
Rated frequency | 50Hz |
Refrigerant | R290 |
Weight of product | 45kg |
Rated capacity | 8.0kg |
GWP | 3 |
CO2-eq | 0.00t |
Quantity of refrigerant | 130g |
Note!
- The rated capacity is the maximum capacity to be dried at one time. Make sure that the dry clothes which are loaded into the appliance do not exceed the rated capacity.
- Do not install the tumble dryer in a room when there is a risk of frost occurring. At temperatures around freezing point, the tumble dryer may not be able to operate properly.
- There is a risk of damage if the condensate water is allowed to freeze in the pump, hoses, and/or condensate water container.