OPT7 AURA Glow Application User Guide
Contact Us | Support Request Page - OPT-7.com – OPT7 Lighting Inc
Installation Guide for OPT7 models including: Aura Pro Glow RV Class B Underglow App and Remoted Controlled, Class B Underglow App and Remoted Controlled, Underglow App and Remoted Controlled, Remoted Controlled, Controlled
AURA Pro Glow RV Class B Underglow Install Guide
File Info : application/pdf, 7 Pages, 1.29MB
DocumentDocumentAURATM PRO UNDERGLOW BLUETOOTH OPT7 GLOW APP & REMOTED CONTROLLED RV CLASS B/B+ FIT INSTALLATION GUIDE RV Class B : 19~23 ft RV Class B+: 19~24 ft RV Class B : 10 ft RV Class B+: 11 ft ON AUTO OFF S+ M+ S- M- RV Class B : 7 ft RV Class B+: 8.1 ft AURA PRO BLUETOOTH CONTROL BOX COMPONENTS A RIGID LIGHT BARS 2×48'' (TWO-SECTION MOVABLE 24") + 8ft EXTENSION WIRE B RIGID LIGHT BARS 1×36'' (TWO-SECTION MOVABLE 18") + 8ft EXTENSION WIRE C ON AUTO OFF S+ M+ S- M- RIGID LIGHT BARS 3×36'' (TWO-SECTION MOVABLE 18") + 18ft EXTENSION WIRE HAND HELD REMOTE AURA PRO BLUETOOTH CONTROL BOX (SCAN QR CODE FOR APP USER GUIDE) Y-SPLITTERS (WATERPROOF) HARDWIRE POWER HARNESS INCLUDES - WIRE MOUNTS, SELF-TAPPING SCREWS, BOOSTER, VELCRO, ZIP TIES MOUNTING KIT INSTALLATION STEP 1 Inspect kit to ensure all contents was included. STEP 2 Decide where to locate the control box and ensure wiring has enough length for light bars to be installed in desired location. IMPORTANT The control box is waterproof, but it should still be installed in a safe area of the vehicle. Please avoid installing it in the engine bay or on heated surfaces. 12V BATTERY FRONT 36" FRONT RIGHT REAR OPT7 LEFT CONTROL BOX IMPORTANT The spare tire is usually located at the bottom of the car. Please pay attention to the position of the spare tire of a suitable place to install the rear light bar to prevent the spare tire from being used normally. 48" + 36" LEFT RIGHT REAR 36" 48" + 36" EXAMPLES FUSE Y-SPLITTER C B EXTENSION WIRE C C Y-SPLITTER The extension wires are on the led bar. Lay out the bars to measure the length prior to install for a successful installation. 1 x 36" (two-section movable 18") LED Bar + 8ft extension wire 1 x 48" (two-section movable 24") LED Bar + 8ft extension wire 1 x 36" (two-section movable 18") LED Bar + 18ft extension wire 1 x 48" (two-section movable 24") LED Bar + 8ft extension wire 1 x 36" (two-section movable 18") LED Bar + 18ft extension wire 1 x 36" (two-section movable 18") LED Bar + 18ft extension wire HOW TO CONNECT POWER HARNESS TO YOUR VEHICLE - Connect the Red wire (+) of power harness to the vehicle battery's positive terminal. - Connect the Black wire (-) of power harness to the vehicle battery's negative terminal or an unpainted area on your vehicle's frame. WARNING Please ensure the Underglow LED Bars / Control Box / Wirings are all mounted away from heated surfaces exceeding from 85°C or 185°F. ! IMPORTANT ! BE SURE TO CONFIRM THE CORRECT DIRECTION OF THE ARROW!! TO AVOID PRODUCT DAMAGE DUE TO INCORRECT INSTALLATION. Flow direction CORRECT INSTALLATION Note the direction of the arrows 1 On 2 3 AUTO Off 4 5 6 S+ M+ S- M- 7 Off AUTO On M+ S+ M- S- STEP 3 Secure Control box in desired location with Velcro or zipties. *Ensure the control box is mounted away from water and heated metal surfaces for optimal performance. STEP 4 Secure the light bars using the zip ties to tie all the wiring away from the moving components. STEP 5 Using the included 21Key E-Z Remote, select your desired color or pattern. 1 Power-ON 2 Automatic Color Change 3 Power-OFF 4 Speed +/- 10 evels 5 Mode +/- 24 Mode 6 Dimmer 10 Levels 7 Color Selection 12 Colors NOTE: When you use this product, keep it within 10m/33ft as much as possible. HOW TO PAIR THE REMOTE? Pair the Device: To pair the remote, reconnect the power, then aim the remote at the control box and hold the ON button until the LED strips flash white. Unpair the Device: To unpair the remote, reconnect the power, then aim the remote at the control box and hold the OFF button until the LED strips flash white. QR CODE TO DOWNLOAD STEP 6 Download the OPT7 GLOW to have the best experience. Download the free "OPT7 GLOW" App · App iOS (12+) available on App Store · Android (8+) available on Google Play Please scan to see the OPT7 GLOW user guide. https://wintis.ladesk.com/362302-OPT7-AURA-Glow-Application-User-Guide OPTION METHOOD To power the kit using an switched 10 AMP fuse tap method, you may purchase the AURA Universal Replacement Fuse Tap Adapter Set & Power Wire on our website. (*Not included; sold separately.) Feel free to contact us using the link below for product inquires or installation support. OPT7 SUPPORT TEAM: https://www.opt-7.com/pages/customer-support GROUND FUSE BOX Y-SPLITTER C B EXTENSION WIRE C C Y-SPLITTER WARNING 1. Connecting to more than 10 AMP will override the kit and cause early failure, ensure it is 10 AMP or less !! 2. Please ensure the Underglow LED Bars / Control Box / Wirings are all mounted away from heated surfaces exceeding from 85 or 185. DISCLAIMER OPT7 Lighting is not liable for damages or personal injuries while installing this product. The Installation Guide is intended as assistance to reduce setup time. OPT7 Lighting assumes no responsibility for improper installation. If you are unfamiliar with your vehicle or inexperienced with aftermarket upgrades, please seek professional assistance. OPT7 recommends installation for safety and guidance. Modified installations or installation recommendations not specified by OPT7 Lighting will void product warranty.