User Manual for muonio models including: C2640, 2AZ89C2640, CC2640 Radio Module, Radio Module
Vulpes d.o.o. C2640 2AZ89C2640 2AZ89C2640 c2640
CC2640 RADIO MODULEE CC2640 RADIO MODULE is a lowcost and low-power consumption module which has all of the Bluetooth Smart 4.1 functionalities. The CC2640 RADIO MODULE module fully supports the single mode Bluetooth Low Energy operation, and the output power can support class 2. The module provides the ability to either put your entire application into the integrated ARM Cortex M3 microcontroller, or use the module in Network Processor mode in conjunction with the microcontroller of your choice. FCC ID: 2AZ89C2640 USER MANUAL Features & Applications Built in CC2640F128 Bluetooth Smart (BLE 5.0) System-On-Chip (SOC) 128 kB Flash / 20 kB SRAM Size: 55 mm x 20 mm Operating Voltage: 1.8V to 3.8V Operating Temperature: -40 to +85C 8.4 mA Transmit Mode 7.4 mA Receive Mode 1A Standby (SRAM/CPU retention andRTC running) with quick 100 s start up 200nA Shutdown 61A/MHz Active CPU Current Drivers, Bluetooth Low Energy Controller, and bootloader in ROM Flexible peripheral set On board 32 .768kHZ and 24 MHz Crystals Worldwide Acceptance Applicatons Consumer electronics Mobile phone accessories Sports & Fitness equipment HID applications Home and Building Automation, Lighting Control, Alarm and Security Electronic Shelf Labeling, Proximity Tags And many more... Electrical Characteristics ITEM TEST REQUIREMENT REMARKS Voltage supply 1.8-3.8V DC Center frequency 2402-2480MHz Programmable Frequency error ±50KHz Modulation O-QPS Receiving sensitivity -97dBm High gain Mode Receiving current 5.9mA Transmitting current 9.1mA TX Power 5dBm Sleep consumption At power mode2 1uA Sleep Timer ON Sleep consumption At power mode3 0.1uA External interrupts Transmit distance >60M BER<0.1% Antenna 50 ohm Module size 55 mm*20 mm RECOMMENDED OPERATING CONDITIONS MIN MAX UNIT Operating ambient temperature range, TA -30 85 °C Operating supply voltage 1.8 3.8 V CAUTION: ESD sensitive device. Precautions should be used when handing the device in order to prevent permanent damage. 20.00 2.50 55.00 1.50 55.00 Pin assignemet NAME NO. TYPE VDD 14,15 Power GND 13,16, 39 Power DIO_0 35 Digital I/O DIO_1 36 Digital I/O DIO_2 37 Digital I/O DIO_3 38 Digital I/O DIO_4 1 Digital I/O DIO_5 2 Digital I/O DIO_6 3 Digital I/O DIO_7 4 Digital I/O DIO_8 5 Digital I/O DIO_9 6 Digital I/O DIO_10 7 Digital I/O DIO_11 8 Digital I/O DIO_12 9 Digital I/O DIO_13 10 Digital I/O DIO_14 11 Digital I/O DIO_15 12 Digital I/O DIO_16 19 Digital I/O DIO_17 20 Digital I/O DIO_18 21 Digital I/O DIO_19 22 Digital I/O DIO_20 23 Digital I/O DIO_21 24 Digital I/O DIO_22 25 Digital I/O DIO_23 27 Digital/Analog I/O DIO_24 28 Digital/Analog I/O DIO_25 29 Digital/Analog I/O DIO_26 30 Digital/Analog I/O DIO_27 31 Digital/Analog I/O DIO_28 32 Digital/Analog I/O DIO_29 33 Digital/Analog I/O DIO_30 34 Digital/Analog I/O JTAG_TMSC 17 Digital I/O JTAG_TCKC 18 Digital I/O RESET_N 26 Digital input Pin countig starts top left. 1 14 15 39 26 25 FCC regulatory compliance statement §15.19 Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. §15.21 Information to user Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. List of applicable FCC rules: 47 CFR Part 15, Subpart C 15.203 47 CFR Part 15, Subpart C 15.205 47 CFR Part 15, Subpart C 15.207 47 CFR Part 15, Subpart C 15.209 47 CFR Part 15, Subpart C 15.247 47 CFR Part 2 2.1091 Summarize the specific operational use conditions This module can be used in IOT devices, the input voltage to the module is nominally 5V. Only the embedded integral antenna is allowed. Any other external antenna is prohibited. Limited module procedures This module is not a limited module. Trace antenna designs The antenna is not a trace antenna. RF exposure considerations This Module complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Antennas If you desire to increase antenna gain and either change antenna type or use same antenna type certified, a Class II permissive change application is required to be filed by us, or you (host manufacturer) can take responsibility through the change in FCC ID (new application) procedure followed by a Class II permissive change application. FCC regulatory compliance statement Label and compliance information Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: "Contains FCC ID: _2AZ89C2640_" any similar wording that expresses the same meaning may be used. § 15.19 Labelling requirements shall be complied on end user device. Labelling rules for special device, please refer to §2.925, § 15.19 (a)(5) and relevant KDB publications. For E-label, please refer to §2.935. Information on test modes and additional testing requirements The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module. The module is limited to installation in mobile application, a separate approval is required for all other operating configurations, including portable configurations with respect to §2.1093 and difference antenna configurations. Test software: SmartRF Studio 7 2.10.0 Additional testing, Part 15 Subpart B disclaimer This modular transmitter is only FCC authorized for the specific rule parts listed on our grant, host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. Host manufacturer in any case shall ensure host product which is installed and operating with the module is in compliant with Part 15B requirements. Please note that For a Class B or Class A digital device or peripheral, the instructions furnished the user manual of the end-user product shall include statement set out in §15.105 Information to the user or such similar statement and place it in a prominent location in the text of host product manual. Original texts as following: Sample Operation Description Sample Operation Description For Class B Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. The 24MHZ Hz crystal oscillator drives the base of Y2. The modulation provided by IC TXC-7M-32.000MEEQ-T. The output of has the matching network consisting of balun 2450BM14G0011 that limit the harmonic content and effect the proper coupling of the antenna to the output stage. Antenna, Ground and Power Source The antenna consists of a 2.4GHz Meander line SWRU120C antenna. Antenna gain: 1.1 to 3.3 dBi. There is no external ground connection. The ground is only that of the printed circuit board. Electric current is supplied by Input VCC; Output: 3.3 Vd.c.. Operation Descriptions The transmitter is a Portable Wireless Music System operating at 2400-2483.5MHz band. The transmitter is powered by 3.3 Vd.c and the transmitting frequency is crystal controlled. The operation is achieved by different combinations of form pulse modulating signal on the 2400MHz carrier frequency. When the NTAG is positioned in the RF field, the high speed RF communication interface allows the transmission of the data and enable the Bluetooth pairingAdobe PDF Library 15.0 Adobe InDesign 16.0 (Windows)