Home Decorators Collection Britton LED 52 in. Ceiling Fan

Customer Service

Questions, problems, missing parts? Before returning to the store, call Home Decorators Collection Customer Service:

8 a.m. - 7 p.m., EST, Monday-Friday

9 a.m. - 6 p.m., EST, Saturday

1-800-986-3460

WWW.HOMEDEPOT.CA

THANK YOU

We appreciate the trust and confidence you have placed in Home Decorators Collection through the purchase of this ceiling fan. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Home Decorators Collection!

Table of Contents

• Safety Information
• Warranty
• Pre-installation
• Installation
• Assembly
• Operation
• Care and Cleaning
• Troubleshooting
• Service Parts

Safety Information

READ AND SAVE THESE INSTRUCTIONS.

• To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before beginning.
• All wiring must be in accordance with the National Electrical Code "ANSI/NFPA 70-1999" and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
• The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 lbs. Use only CUL Listed outlet boxes marked "FOR FAN SUPPORT."
• The fan must be mounted with a minimum of 7 ft. clearance from the trailing edge of the blades to the floor.
• To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning the fan.
• Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly dampened cloth will be suitable for most cleaning.
• After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.
• All setscrews must be checked and retightened where necessary before installation.
• This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

WARNING: To reduce the risk of fire or electric shock, this fan should only be used with fan speed control part No.:DL-1167RYS-02, manufactured by S.Q.M Co Ltd.

WARNING: To reduce the risk of personal injury, do not bend the blade arms (also referred to as flanges), when installing the brackets, balancing the blades, or cleaning the fan.

WARNING: Do not insert foreign objects between rotating fan blades.

WARNING: To reduce the risk of fire, electric shock, or personal injury, mount the fan to the outlet box marked acceptable for fan support with the screws provided with the outlet box.

CAUTION: To reduce the risk of personal injury, use only the screws provided with the outlet box.

Warranty

Home Decorators Collection warrants the fan motor to be free from defects in workmanship and material for a period of lifetime after the date of purchase by the original purchaser. The LED light kit is warranted for 5 years. All other fan parts (excluding glass or acrylic blades) are warranted for 2 years. To obtain warranty service, a copy of the receipt is required. Costs of removing and reinstalling the product are the customer's responsibility. This warranty does not cover damage from accident, misuse, improper installation, or accessories. Changes in brass finish due to climate are not covered. A slight wobble is normal. Servicing by unauthorized persons voids the warranty. This warranty disclaims implied warranties of merchantability and fitness for a particular purpose to the extent permitted by law. Some states do not allow limitations on implied warranty duration or exclusion of incidental/consequential damages. This warranty gives specific legal rights, and other rights may vary by state. Shipping costs for returns are the customer's responsibility.

Contact Customer Service at 1-800-986-3460 or visit www.HOMEDEPOT.CA.

Pre-Installation

SPECIFICATIONS

NOTE: These are approximate measures. They do not include amps and wattage used by the light kit.

Intertek ETL C US LISTED

TOOLS REQUIRED

• Phillips screwdriver
• Ladder
• Wire stripper
• Electrical tape

HARDWARE INCLUDED

NOTE: Hardware shown to actual size unless noted otherwise in the table below.

PACKAGE CONTENTS

Installation

MOUNTING OPTIONS

WARNING: To reduce the risk of fire, electric shock, or personal injury, mount the fan to an outlet box marked acceptable for fan support using the screws provided with the outlet box. An outlet box commonly used for the support of lighting fixtures may not be acceptable for fan support and may need to be replaced. If in doubt, consult a qualified electrician.

If your ceiling fan does not have an existing CUL-listed mounting box, then install one using the following instructions:

• Disconnect the power by removing the fuses or turning off the circuit breakers.
• Secure the outlet box (1) (not included) directly to the building structure. Use appropriate fasteners and materials (not included). The outlet box and its bracing must be able to fully support the weight of the moving fan (at least 35 lbs.). Do not use a plastic outlet box.

The illustrations below show two different ways to mount the outlet box (not included).

To hang your fan where there is an existing fixture but no ceiling joist, you may need an installation hanger bar (2) (not included) as shown above.

Assembly – Hanging the Fan

1 Installing the mounting bracket to the electrical box

WARNING: To reduce the risk of fire, electric shock or other personal injury, mount the fan only to an outlet box or supporting system marked acceptable for fan support and use the mounting screws provided with the outlet box.

• Place the slots (LL) from the mounting bracket (B) over the two mounting screws (KK) provided with the outlet box.
• Slide the mounting bracket (B) until it locks in place at the narrow section of the slots (LL).
• Securely tighten the two mounting screws (KK) provided with the outlet box.
• If the outlet box is not included the mounting screws, please use the two machine screws (HH) and the two metal washers (II) and the two star washers (JJ) to install the mounting bracket (B).

2 Hanging the fan to the mounting bracket

• Remove the mounting plate screw (FF) from the mounting bracket (B) and loosen the other three mounting plate screws (FF) approximately 1/4 turn. Place the mounting plate screw (FF) that was removed aside for use later.
• Lift the fan motor assembly (F) by hanging the square hole (NN) of the mounting plate (D) on the hook (MM) from the mounting bracket (B) allowing it to hang.

3 Installation of safety cable

The safety cable (00) from fan motor assembly (F) prevents the fan from falling. Secure the safety cable (00) to the ceiling joist with a wood screw and washer (not included).

4 Making the electrical connections

WARNING: To avoid possible electrical shock, ensure the electricity is turned off at the circuit breaker or main fuse box before wiring.

WARNING: Check to see that all connections are tight, including the ground, and that no bare wire is visible at the wire nuts, except for the ground wire.

Follow the steps below to connect the fan to your house supply wires. Secure the wire nuts (DD) supplied with your fan by wrapping the connections with electrical tape.

• Connect the black (hot) wire from the ceiling to the black wire marked "AC in L" from the receiver (E).
• Connect the white (neutral) wire from the ceiling to the white wire marked "AC in N" from the receiver (E).
• Connect the ground wire (green or bare copper) of the outlet box to the ground wire of the mounting plate (D) and the ground wire of the mounting bracket (B).
• Secure the wire connection with a plastic wire nut provided with the electrical hardware.
• After connecting the wires, spread them apart so that the green and white wires are on one side of the outlet box (1) and the black wires are on the other side. Carefully tuck the wire connections up into the outlet box (1).

5 Installing the fan motor assembly

• Lift and place the key holes (PP) of the mounting plate (D) over the three screws (FF) previously loosened on the mounting bracket (B) and turn the mounting plate (D) until it locks in place and no longer turns.
• Secure by tightening the three screws (FF) previously loosened and the screw (FF) previously removed.

WARNING: Ensure you complete this step correctly and follow all steps. Failure to correctly follow this step might cause the fan to fall.

6 Installing the fan housing

• Align the four large screws (GG) pre-locked on the fan housing (C) to the slotted holes (QQ) of the mounting bracket (B). Turn the fan housing (C) at the right side and twist the screws (GG) to the end of the slotted holes (QQ) until they lock in place and no longer turn.

Assembly – Attaching the Fan Blades

7 Fastening the flywheel to the fan motor assembly

Tighten the flywheel (G) onto the bottom of the fan motor assembly (F) by using the five flywheel screws (CC).

8 Installing the fan blades to the flywheel

• Insert the blade (A) through the slot on the flywheel (G). Fasten the fan blade (A) to the flywheel (G) by using the three blade screws (AA) and the three fiber washers (BB) and tighten them securely. Repeat this step for the other four blades.

NOTE: When installing the blades, ensure the sides with "THIS SIDE UP" face the ceiling.

Assembly – Installing the Light Kit

9 Attaching the LED assembly to the fan motor assembly

CAUTION: To Reduce The Risk Of Electric Shock, Disconnect The Electrical Supply Circuit To The Fan Before Installing The Light Kit.

• While holding the LED assembly (H) under your fan, firmly snap the wire connection plugs (RR) together.
• Attach the LED assembly (H) to the locking plate (SS) of the fan motor assembly (F) by twisting tightly.

Operation

REMOTE CONTROL OPERATING INSTRUCTIONS

Install a 12V battery (K) into the remote control (I). To prevent damage to the remote control, remove the battery if not used for long periods of time.

WARNING: Do not short-circuit, disassemble, heat up, connect improperly, or dispose of used batteries in fire. Do not recharge or mix batteries with used or other battery types. Immediately remove used batteries.

Restore power to the ceiling fan and test for proper operation.

Fan Speed Buttons:

• ●●● buttons: These buttons are used to set the fan speeds as follows;
• ○ = Low Speed
• ● = Medium Speed
• ●● = High Speed

"   " button: Turns the fan off.

"   " button: Turns the light ON or OFF. Press and hold the button to set the desired brightness.

"   " reverse button (TT): Controls the fan direction.

Note: To operate the reverse function on this fan, press the reverse button when the fan is running.

Warm Weather (forward)

A DOWNWARD airflow creates a cooling effect. This allows you to set your air conditioner on a warmer setting without affecting your comfort.

Cool Weather (Reverse)

An UPWARD airflow moves warmer air off the ceiling area. This allows you to set your heating unit on a cooler setting without affecting your comfort.

SUMMER OPERATION COUNTER CLOCKWISE

WINTER OPERATION CLOCKWISE

Operation (continued)

INSTALLING THE REMOTE CONTROL HOLDER

• Attach the remote control holder (J) with the two remote control holder mounting screws (EE).

Care and Cleaning

Do

• Check the support connections, brackets, and blade attachments twice a year. Ensure they are secure. Because of the fan's natural movement, some connections may become loose over time. It is not necessary to remove the fan from the ceiling.
• Clean your fan periodically. Use only a soft brush or lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration or tarnishing.
• (Optional) Apply a light coat of furniture polish to the wood blades.
• (Optional) Cover small scratches with a light application of shoe polish.

Do not

• Do not use water when cleaning. Water could damage the motor, or the wood, or possibly cause an electrical shock.
• Do not apply oil to your fan or motor. The motor has permanently-lubricated sealed ball bearings.

Troubleshooting

WARNING: Ensure the power is off at the electrical panel box before you attempt any repairs. Refer to the section "Making the Electrical Connections" on page 10.

Service Parts