Shenzhen ERS Technology-led, led lighting, led highbay light, led panel light, led batten light, energy saving, VEET, IPART
Shenzhen ERS Technology-led, led lighting, led highbay light, led panel light, led batten light, energy saving, VEET, IPART
Instruction Manual for ERS tech models including: ERS-F30W-SP, LED Flood Light, ERS-F30W-SP LED Flood Light
LED Floodlight with Sensor 50W, 5000K, Remote Control
File Info : application/pdf, 2 Pages, 475.05KB
DocumentDocumentLED Flood Light Accessories x1 x1 Factory setting of sensor: When turn on the lamp, sensor function is closed; If you need to open the sensor, please use our remote controller as below. Show Case: 1. Press "ON" to open sensor function, default setting: daglight (OFF), hold time (2 seconds), standby brightness 0%; 2. Set the data you need. For instance, you need the lamp holds on 2 mins after you leaving in site and then dimming to half brightness, just press the "2 min" in hold Time section, and press "50%" in standby brightness section. If need to change daylight sensor date, for instance, you want the lamp turns on when the brightness is300, just press "300 Lux" in on Lux section (Light Threshold); "Disable" is to close daylight sensor function. If want to close the sensor function, just press "OFF". Installation 1.Switch off the power supply before installation. 2.Fix the installation bracket to the wall, then adjust the angle, and connect the power plug. 3.Fix the installation bracket to the ceiling, then adjust the angle, and connect the power plug. D: Press one time, Daylight Sensor working only. On: Press one time, work with default setting. Sc1: Hold on 30 minutes and then dimming down to its 50% luminosity. Daylight Sensor OFF. Sc2: Hold on 10 minutes and then dimming down to its 20% luminosity. Daylight Sensor OFF. 100% 75% Detection Range D ON 50% OFF 20% M 5 25 Lux Lux On lux 100 300 Lux Lux 2 30 Sec Sec Hold time 5 15 Min Min 50 Lux 600 Lux Disable 60 2 Sec Min 30 60 Min Min 0% 20% Standby brightness 50% 60% 30% 40% 80% 100% Sc1 Sc2 Sc3 Scene Technical Parameter M: Press one time, Motion Sensor working only. Record the current environmemt lux. Sc3: Hold on 30 seconds and then turn OFF. Daylight Sensor OFF. Input Voltage AC220-240V,50Hz LED Chips Beam Angle 120° Sensor Driver ERS driver Power Factor CCT 3000-6500K CRI Working Temp -20~+50 IP Rating 1 SMD 2835 Daylight & Microwave Motion Sensor 0.9 Ra80 IP65 4.Fix the installation bracket to the ground, then adjust the angle, and connect the power plug. 5.Switch on the power supply after installation. 2 Reminder We appreciate your choice! Please read the instruction manual before installation and keep it well. Warning To aviod the accident of damage, falling, electric shock or fire, please do not reform the lamp or replace the accessories and confirm with us if you need to change the mounting method. Please authorize the installation to qualified installation personnel and obey to the instruction manual. Any unsuitable installation will easily cause the accident of falling, electric shock and fire etc. Please cut off the power before installation or any maintenance of the lamp. Please cut off the power when it smokes or smells awfully since the accident of fire or electric shock may incur. Ask the qualified personnel for maintenance. Please do not dismantle the lamp by yourself since the accident may incur. Please do not touch the driver when the lamp works. Application This product is suitable for billboard, road, tunnel, bridge and culvert, square, building. Troubleshooting&Solutions Malfunction Troubleshooting Solutions 1.Check whether the power line is properly connected. 1.Reconnect the power wire. 2.Check whether the power plug is loosen. 2.Re-plug the loosen power plug. Not working 3.Driving power supply failure. 4.L3E.DDricvhinipg bproewaekrdsouwpnp.ly failure. 5.Daylight function is turned on. 1.How to use the remote control to set the brightness. LED dim or flashing 2.The sensing function turned on, and the test function turned on. 3.The output of the driver is abnormal. 4.LED chip breakdown. 3 Warranty Five years warranty. During the warranty period, the client shall return the failed parts by courier for inspection and repair. After inspection and repair, the supplier shall send the fixed parts or new parts back. Each party shall bear the freight cost accordingly. Keep the warranty card as the warranty certificate. The following conditions are not covered by the warranty, and the supplier provides maintenance services by charging maintenance fee: (1) All artificial damages, including damages from operation, usage, storage unconformity with the instruction manual, abnormal working condition etc; (2) Dismantling, maintenance, modification or unqualified repairing for the products without the supplier's authorization; (3) No warranty cards and documents; (4) Damages caused by user's improper delivery or due to force majeure (including fire, flood, thunder hit, earthquake etc). All rights reserved. Name Number User Warranty Card Type Date Tel./E-mail Date Issue Note Item List 1.Lamp body 2.90 degree aluminum reflector 3.120 degree aluminum reflector 4.Transparent reflector 5.Transparent reflector connecting plate and screws 6.Aluminum reflector connecting plate,snap ring and screws 7.Rubber ring 8.The reflector seaing gasket 9.Transparent reflector organic glass plate,snap ring 10.Accessory Screws 11.Instruction Manual (including Warranty Card and Item List) 12.Qualification Certificate pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs pcs LED Flood Light Instruction Manual Website: www.erstech.com.au / www.erstech.com.cn 4 5