Instruction Manual Smart Baby Camera
Model No. IPC163
1. What's Included
- Smart Baby Camera
- Micro USB Charging Cable ?
- Reset Pin ?
- AC Charger ?
2. Parts of the Camera
Description of camera components:
- 1. Reset Button
- 2. Micro SD Card Slot
- 3. Temperature Sensor ?️
- 4. Light Sensor ?
- 5. Built-in MIC ?
- 6. Lens ?
- 7. Indicator Light ?
- 8. Night Lamp ?
- 9. Micro USB Port
- 10. Tripod Mount (optional)
- 11. Dual Speakers ?
- 12. Magnetic Base (optional)
- 13. Teddy Silicon Case (optional)
Resetting the Camera: If the camera fails to connect, use the provided reset pin to press and hold the "Reset" button on the back of the camera until the indicator light turns red. Release the button and wait approximately 15 seconds for the system to reboot.
Installing the Memory Card: A Class 4 or higher Micro SD memory card (up to 32GB) is required for normal use.
3. Initial Setup
Turning On the Camera
Connect the power supply to the IP Camera and the AC charger. The RED indicator light will turn on.
Indicator Light Status
- Flashing Quickly (Red): The camera is in setting mode and ready for setup via your mobile device.
- Steady (Blue): The camera is successfully connected to the Wi-Fi network.
Camera Operation & System Requirements
Preparations before use:
- Mobile device system requirements: Android OS 4.4 or higher ?, iOS 9.0 or higher ?.
- You will need: A smartphone or tablet, the IP Camera, and a Router.
Install the App
Use your mobile phone or tablet to search for "TuyaSmart" in Google Play (for Android OS) or the Apple App Store (for iOS). Install the app by following the on-screen instructions.
Available on the iPhone: ? App Store
GET IT ON: ▶️ Google Play
Register an Account
If this is your first time using the app, you need to register an account. Follow the prompts and review the Privacy Policy. By registering, you agree to the terms.
4. Connecting Your IP Camera with the App
Note: Your IPC Camera is supported only on a 2.4GHz Wi-Fi network. Ensure your mobile device is connected to a 2.4GHz Wi-Fi network for setup.
Step 1: After installing the app, launch "TuyaSmart". Follow the prompts to set up the app. Tap '+' or 'Add Device' from the home page. Select 'Security & Sensor', then choose 'Smart Camera'.
Step 2: Power on the device. Ensure the indicator light is flashing quickly or a prompt tone is heard. Tap 'next step'. Confirm your smart device is connected to a 2.4G Wi-Fi network and tap 'Confirm'.
Step 3: The app will guide you to scan the mobile device with the camera. When you tap 'Continue', the mobile phone will display a QR code. Hold the camera 15 to 20 cm in front of the mobile device for the camera to scan the QR code.
Step 4: During connection, ensure your router, mobile, and device are as close as possible. Once the camera receives the information from the mobile device, the camera indicator will turn and stay blue, indicating a successful connection. Your camera's live view with streaming video will open.
Troubleshooting
Try This:
- Ensure the Wi-Fi router supports DHCP protocol and that the DHCP option is turned on.
- Verify the camera and your mobile device are connected to the same Wi-Fi router.
- Confirm you have selected the correct 2.4GHz router in your device's Wi-Fi settings.
- Enter the correct password for the selected router.
- Ensure you are within the Wi-Fi range of the router and that the Wi-Fi router is enabled.
- Make sure the camera is properly powered on and the Wi-Fi router has SSID broadcasting enabled.
Try This:
- Check your home upload speed. Minimum requirements are 1Mbps for 480P stream, 2Mbps for 720P, and 4Mbps for 1080P.
- Clean the camera lens if it is dirty or has fingerprint marks.
Try This:
- Verify that the camera is powered on and properly plugged in.
Specifications
| Item | Specification |
|---|---|
| Image Sensor | 1/2.7" Colour CMOS |
| Recording Resolution | 1920 x 1080 15fps, 640 x 480 20 fps |
| Viewing Angle | 100°(D) |
| Night Vision | up to 5m |
| Video Compression | H.264 |
| Audio | Two-way talk |
| WIFI | 2.4GHz |
| Wireless Security | WEP, WPA, WPA2 |
| Power Consumption | up to 5W |
| Micro SD Card | up to 32GB Class 10 |
FCC Compliance Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy. If not installed and used according to instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
