User Guide for TELESAIL models including: PM4204454, 2A29YPM4204454, PM4254 FTTH Home Gateway, PM4254, FTTH Home Gateway
Radisys Corporation PM4204454 Premium ONU 2A29YPM4204454 2A29YPM4204454 pm4204454
4 W EB Login This m achine support s WEB m anagem ent . You can log in t o 192.168.1.1 ( default I P address) from any PC t o get relevant inform at ion. The st eps are as follows: 1) Change t he net work segm ent of t he PC t o 192.168.1.X and connect it to any network port of the m achine with a network cable; 2) Ent er ht t p: / / 192.168.1.1 in Chrom e, press Ent er t o pop up t he login page, enter the usernam e and password (adm in/ adm in) , and then enter the system m anagem ent page. 5 Matters Needing Attention 1) This device is an indoor st ruct ure, it can not be used in places that are easily invaded by rainwater; it should have proper space in t he indoor box t o facilit at e heat dissipat ion; Recom m ended for use below 2000m above sea level. 2) The fiber input and t he cable out put m ust be reserved for a cert ain lengt h t o avoid accident s caused by t oo short ; t he opt ical int erface in t he ONU is t he SC/ APC head. Do not m isplace or t he end faces are inconsist ent . 6 Accessories 1) . Ext ernal power supply * 1: AC100V- 240V/ DC12V/ 1.5A 2) . User Guide * 1 3) . The cert ificat e of conform it y has been affixed t o t his m anual. Cert ificat ion I nspector: Dat e: PM4254 FTTH Hom e Gat eway User Guide 1 Overview PM4254 GPON ONT is a FTTH gat eway,for sm all and m edium - sized businesses, SOHO office and hom e users, int egrat ing GPON, WI FI . This series of product s com plies wit h t he G.988 int ernat ional st andard and has good int eroperabilit y and operabilit y, enabling int eroperabilit y wit h m ainst ream m anufact urers' OLT devices. 2 Main Specifications OPTI CAL I TEM Wo r k in g w av elengt h TX POWER RX Sensit ivit y optic connector WI FI UNI T nm dBm dBm / / SPEC TX1 3 1 0 RX1 4 9 0 1- 4( GPON) -28 SC/ APC 2.4G:802.11 b/g/n 2.4GHz 300Mbps 5G:802.11 a/an/acGHz 867Mbps TYPE / HGU POWER V/ A OTHER Size mm Operat ing tem perature DC12V 1.5A 196*135*31 - 540 3 I nstructions for Use 1 ) Pow e r Conne ct ion This m achine is support ed by t he power adapt er. First ly, connect the DC 12V output cable of the power adapter to the DC 12V port of the m achine, and then plug the external regulated power supply int o t he AC100~ 240V of t he m ains. The power indicat or on t he panel is on, indicating that the power supply is working norm ally. 2 ) I N TERFACES I NTERFACES ON/ OFF Po w er Opt ical LAN1- LAN4 Reset WLAN FXS I ntroduct ion Power sw it ch but t on Power input int erface, DC 12V/ 1.5A GPON fiber int erfaces, using SC/ APC fiber access LAN service int erface Reset but t on WI FI swit ch VOI P I nt erface 3 ) I ndicators Description I ndicator Po w er PON LOS LAN1- LAN4 WI FI ( 2.4G/ 5G) St at us Descript ion ON The device is powered on norm ally. OFF The device is not powered on. Tw inkling Received light , device not regist ered The ONU is connect ed t o t he OLT and regist ered ON su ccessf u lly . OFF No opt ical received, device not regist ered Tw inkling Fiber break or opt ical power exceeds lim it OFF ONU accept s norm al opt ical power The net work port is connect ed but no dat a is ON transm itt ed. Twinkling Net work port has dat a t ransm ission The device is not powered on or t he net work port OFF is not connected to the term inal device. ON WI FI works fine Tw inkling WI FI has dat a t ransm ission OFF WI FI work abnorm ally ON The caller is ringing FXS1/ FXS2 Tw inkling Means t he user is off t he phone or on t he phone OFF free 4 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-collocation statement. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution! Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 5 Canada Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 1) L'appareil ne doit pas produire de brouillage; 2) L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformité de rf. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ou émetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps. the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; 1. the device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; 2. for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit; 1. les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; 2. le gain maximal d'antenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer à la limite de p.i.r.e.; 6 Mounting an ONU onto the wall 1. Mark two positions with the same spacing as that between the two mounting holes of the ONU using a marker on a wall. 2. Select a proper drill bit according to the outer diameter of the screws,Use a hammer drill to drill the marked positions on the wall. Then clean the holes and install two expansion bolts. 3. Use a screwdriver to fasten the screws into the expansion bolts,reserving 13mm ends out of the wall,and mount the ONU onto the screws. NOTE It is recommended to use two screws with a diameter of 6mm and a length greater than 20mm.Adobe PDF Library 11.0