OUKITEL WP8 Pro Rugged Smartphone

Overview

The OUKITEL WP8 Pro is a rugged smartphone. On the front, from top to bottom, it features an earphone grille ?, a receiver [receiver], volume up [volume-up] and volume down [volume-down] buttons, and a smart key [smart-key]. The top edge has a front camera ? (front) and a secondary camera ? (secondary). The back of the device features a rear camera ? (rear) and a depth camera ? (depth), accompanied by a flash light ?. Below the cameras is the IP68 rating indicator and the OUKITEL branding. Further down are the SIM card & TF card slot ?, the power key ?, and a fingerprint sensor ?. The bottom edge has a USB interface ? (USB) for charging and data transfer, and a microphone ?. The speaker ? is located on the back. The accessories include a quick charger ⚡, a MICR 5pin cable [mic-5pin], an OTG cable [otg-cable], and a SIM card pin ejector [sim-ejector].

Specifications

Basic Parameters

Camera

Connection (I/O)

Other Features

• Video Support: AVI, MP4, WMV, RMVB, MKV, MOV, ASF, RM, FLV
• Audio Support: AAC/AAC+/AMR/AWB/MP3/WMA/VORBIS/FLAC/APE
• Image Support: JPEG, BMP, GIF, PNG

Dimensions

Package Contents

• 1x Warranty card
• 1x USB data cable
• 1x Charger
• 1x Multi-language Manual
• 1x OTG Cable

Warnings

• ⚠️ Use only OUKITEL-approved batteries specifically designed for your phone. Incompatible batteries can cause serious injuries or damage to your phone.
• ⚠️ Never place batteries or phones on or in heating devices, such as microwave ovens, stoves, or radiators. Batteries may explode when overheated.
• ⚠️ Use careful with the earphone; excessive sound pressure can cause hearing loss.
• ⚠️ CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. Dispose of used batteries according to the instructions.
• The product shall only be connected to a USB interface of version USB 2.0.
• Adapter shall be installed near the equipment and shall be easily accessible.
• The plug is considered the disconnect device of the adapter.

Compliance and Safety Information

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Specific Absorption Rate (SAR) Information

This Mobile Phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.

Body-worn Operation

This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 10mm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.

FCC ID: 2ANMU-WP8PRO

[fcc-logo] [ce-logo] [rohs-logo]

Manufacturer Information

Manufacturer Name: SHENZHEN YUNJI INTELLIGENT TECHNOLOGY CO., LTD

Manufacturer Address: A-SIDE A2 BUILDING 2/F ENET NEW INDUSTRIAL PARK, NO.20 DAFU INDUSTRIAL ZONE, AOBEI COMMUNITY, GUANLAN, LONGHUA NEW DISTRICT, SHENZHEN CHINA

Website: www.oukitel.com