User Manual for Beijer ELECTRONICS models including: GT-7408 Power Supply Module, GT-7408, Power Supply Module, Supply Module, Module
File Info : application/pdf, 20 Pages, 3.32MB
DocumentDocumentUser Manual GT-7408 Power Supply Module Potential distributor module, 8 connections for shield, cage clamp, 10 pt removable terminal Doc ID: 151806 2025-02-20 Copyright © 2025 Beijer Electronics AB. All rights reserved. The information in this document is subject to change without notice and is provided as available at the time of printing. Beijer Electronics AB reserves the right to change any information without updating this publication. Beijer Electronics AB assumes no responsibility for any errors that may appear in this document. All examples in this document are only intended to improve understanding of the functionality and handling of the equipment. Beijer Electronics AB cannot assume any liability if these examples are used in real applications. In view of the wide range of applications for this software, users must acquire sufficient knowledge themselves in order to ensure that it is correctly used in their specific application. Persons responsible for the application and the equipment must themselves ensure that each application is in compliance with all relevant requirements, standards, and legislation in respect to configuration and safety. Beijer Electronics AB will accept no liability for any damage incurred during the installation or use of equipment mentioned in this document. Beijer Electronics AB prohibits all modification, changes, or conversion of the equipment. Head Office Beijer Electronics AB Box 426 201 24 Malmö, Sweden www.beijerelectronics.com / +46 40 358600 Table of Contents 1. About This Manual ......................................................................................... 5 1.1. Symbols Used in This Manual ................................................................... 5 2. Safety ....................................................................................................... 6 2.1. Product Certifications ........................................................................... 6 2.2. General Safety Requirements .................................................................. 6 3. About the G-series System ............................................................................... 7 3.1. IO Process Data Mapping ........................................................................ 8 4. Specifications .............................................................................................. 9 4.1. Environmental Specifications ................................................................... 9 4.2. General Specifications ........................................................................... 9 4.3. Technical Specifications ........................................................................ 10 5. Wiring Diagram ........................................................................................... 11 6. LED Indicator .............................................................................................. 12 7. Wiring Configuration Example .......................................................................... 13 8. Hardware Setup .......................................................................................... 14 8.1. Space Requirements ............................................................................ 14 8.2. Mount Module to DIN Rail ...................................................................... 15 8.3. Mount Removable Terminal Block ............................................................. 17 8.4. Connect Cables to Removable Terminal Block .............................................. 18 8.5. Field Power and Data Pins ..................................................................... 19 Beijer Electronics, Doc ID: 151806 3 2025-02 4 About This Manual 1. About This Manual This manual contains information on the software and hardware features of the Beijer Electronics GT-7408 Power Supply Module. It provides in-depth specifications, guidance on installation, setup, and usage of the product. 1.1. Symbols Used in This Manual This publication includes Warning, Caution, Note and Important icons where appropriate, to point out safety-related, or other important information. The corresponding symbols should be interpreted as follows: WARNING The Warning icon indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury, and major damage to the product. CAUTION The Caution icon indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury, and moderate damage to the product. NOTE The Note icon alerts the reader to relevant facts and conditions. IMPORTANT The Important icon highlights important information. Beijer Electronics, Doc ID: 151806 5 2025-02 Safety 2. Safety Before using this product, please read this manual and other relevant manuals carefully. Pay full attention to safety instructions! In no event will Beijer Electronics be responsible or liable for damages resulting from the use of this product. The images, examples and diagrams in this manual are included for illustrative purposes. Because of the many variables and requirements associated with any particular installation, Beijer Electronics cannot take responsibility or liability for actual use based on the examples and diagrams. 2.1. Product Certifications The product has the following product certifications. 2.2. General Safety Requirements WARNING · Do not assemble the products and wires with power connected to the system. Doing so cause an "arc flash", which can result in unexpected dangerous events (burns, fire, flying objects, blast pressure, sound blast, heat). · Do not touch terminal blocks or IO modules when the system is running. Doing so may cause electric shock, short circuit or malfunction of the device. · Never let external metallic objects touch the product when the system is running. Doing so may cause electric shock, short circuit or malfunction of the device. · Do not place the product near inflammable material. Doing so may cause a fire. · All wiring work should be performed by an electrical engineer. · When handling the modules, ensure that all persons, the workplace and the packing are well grounded. Avoid touching conductive components, the modules contain electronic components that may be destroyed by electrostatic discharge. CAUTION · Never use the product in environments with temperature over 60. Avoid placing the product in direct sunlight. · Never use the product in environments with over 90% humidity. · Always use the product in environments with pollution degree 1 or 2. · Use standard cables for wiring. 2025-02 6 Beijer Electronics, Doc ID: 151806 3. About the G-series System About the G-series System System overview · Network Adapter Module - The network adapter module forms the link between the field bus and the field devices with the expansion modules. The connection to different field bus systems can be established by each of the corresponding network adapter module, e.g., for MODBUS TCP, Ethernet IP, EtherCAT, PROFINET, CC-Link IE Field, PROFIBUS, CANopen, DeviceNet, CC-Link, MODBUS/Serial etc. · Expansion Module - Expansion module types: Digital IO, Analog IO, and Special modules. · Messaging - The system uses two types of messaging: Service messaging and IO messaging. Beijer Electronics, Doc ID: 151806 7 2025-02 About the G-series System 3.1. IO Process Data Mapping An expansion module has three types of data: IO data, configuration parameter, and memory register. The data exchange between the network adapter and the expansion modules is made via IO process image data by internal protocol. Data flow between network adapter (63 slots) and expansion modules The input and output image data depend on the slot position and the data type of the expansion slot. The ordering of input and output process image data is based on the expansion slot position. Calculations for this arrangement are included in the manuals for network adapter and programmable IO modules. Valid parameter data depends on the modules in use. For example, analog modules have settings of either 0-20 mA or 4-20 mA, and temperature modules have settings such as PT100, PT200, and PT500. The documentation for each module provides a description of the parameter data. 2025-02 8 Beijer Electronics, Doc ID: 151806 Specifications 4. Specifications 4.1. Environmental Specifications Operating temperature UL temperature Storage temperature Relative humidity Mounting Shock operating Vibration resistance Industrial emissions Industrial immunity Installation position Product certifications -20°C - 60°C -20°C - 60°C -40°C - 85°C 5% - 90% non-condensing DIN rail IEC 60068-2-27 (15G) IEC 60068-2-6 (4 g) EN 61000-6-4: 2019 EN 61000-6-2: 2019 Vertical and horizontal CE, FCC, UL, cUL 4.2. General Specifications System power dissipation Wiring Weight Module size Max. 30 mA @ 5 VDC IO cable max. 2.0 mm2 (AWG 14) Max. 70 g 12 mm x 99 mm x 70 mm Beijer Electronics, Doc ID: 151806 9 2025-02 Specifications 4.2.1. Dimensions Module dimensions (mm) 4.3. Technical Specifications Field power voltage Field power contacts current Indicator Nominal 24 VDC Max. 10 A Operating Temperature: -40 - 50: Max. 10 A 50 - 70: Max. 7 A 1 LED: 1 green internal bus state 2025-02 10 Beijer Electronics, Doc ID: 151806 5. Wiring Diagram Wiring Diagram Pin no. 0 1 2 3 4 5 6 7 8 9 Shield Shield Shield Shield Shield Shield Shield Shield F 24V F 24G Signal description Beijer Electronics, Doc ID: 151806 11 2025-02 LED Indicator 6. LED Indicator LED no. Status LED function / description Internal bus status LED color Green Channel Status Status Normal signal Absence of network adapter LED Green Off Indicates The unit is operating in normal condition (after normal initialization of G-bus communication, this LED maintains ON status). Network adapter is not connected to this module. 2025-02 12 Beijer Electronics, Doc ID: 151806 Wiring Configuration Example 7. Wiring Configuration Example See the following image for a visual representation of the module's wiring setup. Beijer Electronics, Doc ID: 151806 13 2025-02 Hardware Setup 8. Hardware Setup CAUTION · Always read this chapter before installing the module! · Hot surface! The surface of the housing can become hot during operation. If the device is used in high ambient temperatures, always let the device cool down before touching it. · Working on energized devices can damage the equipment! Always turn off the power supply before working on the device. 8.1. Space Requirements The following drawings show the space requirements when installing the G-series modules. The spacing creates space for ventilation, and prevents conducted electromagnetic interference from influencing the operation. Installation position is valid vertical and horizontal. The drawings are illustrative and may be out of proportion. CAUTION NOT following the space requirements may result in damaging the product. 2025-02 14 Beijer Electronics, Doc ID: 151806 Hardware Setup 8.2. Mount Module to DIN Rail The following chapters describe how to mount the module to the DIN rail. CAUTION The module must be fixed to the DIN rail with the locking levers. 8.2.1. Mount GL-9XXX or GT-XXXX Module The following instructions apply to these module types: · GL-9XXX · GT-1XXX · GT-2XXX · GT-3XXX · GT-4XXX · GT-5XXX · GT-7XXX GN-9XXX modules have three locking levers, one at the bottom and two on the side. For mounting instructions, refer to Mount GN-9XXX Module. Mount to DIN rail Dismount from DIN rail Beijer Electronics, Doc ID: 151806 15 2025-02 Hardware Setup 8.2.2. Mount GN-9XXX Module To mount or dismount a network adapter or programmable IO module with the product name GN-9XXX, for example GN-9251 or GN-9371, see the following instructions: Mount to DIN rail Dismount from DIN rail 2025-02 16 Beijer Electronics, Doc ID: 151806 Hardware Setup 8.3. Mount Removable Terminal Block To mount or dismount a removable terminal block (RTB), see the instructions below. Mount a removable terminal block Dismount a removable terminal block Beijer Electronics, Doc ID: 151806 17 2025-02 Hardware Setup 8.4. Connect Cables to Removable Terminal Block To connect/disconnect cables to/from the removable terminal block (RTB), see the instructions below. WARNING Always use the recommended supply voltage and frequency to prevent damage to the equipment and ensure optimal performance. Connect cable Disconnect cable 2025-02 18 Beijer Electronics, Doc ID: 151806 Hardware Setup 8.5. Field Power and Data Pins Communication between the G-series network adapter and the expansion module, as well as system / field power supply of the bus modules is carried out via the internal bus. It is comprised of 2 Field Power Pins and 6 Data Pins. WARNING Do not touch the data and field power pins! Touching can result in soiling and damage by ESD noise. Pin no. P1 P2 P3 P4 P5 P6 P7 P8 Name System VCC System GND Token output Serial output Serial input Reserved Field GND Field VCC Description System supply voltage (5 VDC) System ground Token output port of processor module Transmitter output port of processor module Receiver input port of processor module Reserved for bypass token Field ground Field supply voltage (24 VDC) Beijer Electronics, Doc ID: 151806 19 2025-02 20Antenna House XSL Formatter V7.4 MR2 Amazon Linux 2 Graviton2 : 7.4.3.63807 (2024-03-22T11:49 09) Antenna House PDF Output Library 7.4.1901