Starlink Gen 3 Router Setup Guide

For Standard Gen 2 Kits

Setup

Ensure your Starlink is set up and connected to the internet before setting up your Gen 3 Router. Connect to your existing Starlink WiFi network from your device.
For optimal performance, place your Gen 3 Router in the line of sight of your Gen 2 Router. It is recommended to have both routers in the same room.
Unbox your Gen 3 Router Kit. The kit includes: Gen 3 Router, Starlink Plug, RJ45 Cover, Gen 3 Router Ethernet Cable (1.5 m / 4.92 ft), Gen 3 Router Power Cable (1.5 m / 4.92 ft), and Power Supply.

Illustration showing the Starlink dish, Gen 3 router, and indoor setup with WiFi signals.

Connect the Router to a power outlet using the power cable and power supply.
Open the Starlink App. Wait 1-2 minutes for a "PAIR NEW MESH NODE" notification.
Tap "PAIR". The node will begin connecting on the NETWORK screen. This process takes approximately 1-2 minutes.

App Screen: New Mesh Node

A new mesh node is trying to join your network.

[PAIR BUTTON]

[BLOCK BUTTON]

Once connected, the node will appear on the NETWORK screen in the App.
Connection confirmed! The Gen 3 Router's light should be solid white. Use the Starlink App to customize settings, check your connection, and more.

Illustrations showing the Starlink App's NETWORK screen with different connection statuses: "Connected to Main Router", "Node disconnected", and "Connected to Main Router" with a mesh node.

WiFi Router Light Status:

Flashing White Light: Trying to connect. If no internet connection is established within 20 minutes, the light will turn red.

Solid White Light: Connected to the internet. Will turn off after 1 hour.

No Light: No power to the router.

Red Light: Not connected to the internet.

Violet Light: Router is in bypass mode. Will turn off after 1 hour. A factory reset is required to exit bypass mode.

Optional Wired Connection

To use your Gen 3 Router as the base router, an ethernet adapter and the provided ethernet cable are required. An ethernet adapter can be purchased from the Starlink shop.

Set up your Gen 3 Router as shown in the diagram.

Diagram illustrating the wired connection setup for the Gen 3 Router.

In the Starlink app, bypass your Router. A factory reset is required to exit bypass mode.

App Screen: BYPASS MODE

[SLIDE TO BYPASS BUTTON]

This is an advanced feature that requires a Starlink Ethernet adapter and a separate Starlink or third-party router. A manual factory reset will be required to reverse this.

Connect to WiFi

You are now connected! The Gen 3 Router's light should be solid white. Use the Starlink App to customize additional settings, check your connection, and more.

Using the Extra RJ45 Ports

Remove the RJ45 cover.
Plug your own ethernet cable into port 1 or 2. Connect the other end of your cable to your third-party hardware.

Diagram showing the RJ45 ports on the Gen 3 Router and how to connect an ethernet cable.

Can't Get Online?

Open the Starlink App to check for alerts, outages, or obstructions.
Check the WiFi router light status (see details above).
Ensure all hardware and cables are securely plugged in and undamaged.
Power cycle the router by unplugging it from power and plugging it back in.
Factory reset the router by pressing the reset button with a paper clip.
If issues persist, contact Starlink Customer Support via the app or the Support section of starlink.com.

	Starlink Gen 3 Router Setup Guide for Standard Gen 1 Kits A comprehensive setup guide for the Starlink Gen 3 Router, specifically for users with Standard Gen 1 Starlink kits. This guide covers unboxing, connecting the router, using the Starlink app, and troubleshooting common issues.
	Starlink Gen 3 Router Performance Installation Guide This guide provides instructions for setting up and connecting the Starlink Gen 3 Router for optimal performance. It covers unboxing, connecting the router, and ensuring proper internet connectivity.
	Starlink Standard Setup Guide: Installation and Connection A comprehensive guide to setting up your Starlink satellite internet system. Learn how to unbox, install the dish, connect the router, find a clear sky view, connect to WiFi, and troubleshoot common issues. Includes instructions for using extra RJ45 ports.
	Starlink Kit Gen 3 Setup Guide: Get Connected Learn how to set up your Starlink Kit, including connecting the Starlink dish, router, and power supply. Follow step-by-step instructions for optimal satellite alignment and Wi-Fi setup.
	Starlink Performance Accessories Guide A comprehensive guide to Starlink Performance accessories, including various mounting solutions, power supplies, and cables designed to enhance connectivity and performance.
	Starlink Gen 3 Router Setup Guide A comprehensive guide to setting up your Starlink Gen 3 Router, including Wi-Fi and optional wired connections.
	Starlink Flat High Performance Accessories Guide Explore Starlink's Flat High Performance accessories, including Wedge Mounts, Pipe Adapter Mounts, various cables, Mesh WiFi Routers, and Ethernet Adapters for enhanced connectivity.
	Starlink Mesh Install Guide: Setup and Troubleshooting Comprehensive guide to setting up your Starlink Mesh WiFi system, including node placement, pairing instructions, and common troubleshooting tips.