MrSteam Warranty Registration
Home | Steam Shower Generators Controls Accessories | MrSteam
Home | Steam Shower Generators Controls Accessories | MrSteam
Instruction Manual for mr steam models including: 100518 SteamLinx Mobile System Control Module, 100518, SteamLinx Mobile System Control Module, Mobile System Control Module, System Control Module, Control Module, Module
File Info : application/pdf, 2 Pages, 280.98KB
DocumentDocumentINSTALLATION INSTRUCTIONS SteamLinx Module and Mobile App allows for seamless control of time and temperature using your smart phone or mobile device. SteamLinx works with all MrSteam controls (for MS generators SN 1174000 and up). Package Contents: · SteamLinx A with Integral Cable · SteamLinx B and Ethernet Cable · Power Supply and Cable · Instructions These instructions contain safety alert symbols and panels. These alert symbols and panels identify potential safety hazards and provide important information for the installation and use of SteamLinx. Read the Installation, Operation and Maintenance Manual for Steambath Generator Systems (PUR100472) before installation of SteamLinx to insure safety and proper installation of the steam Generator. A free replacement manual is available by calling MrSteam Customer Service, or it can be downloaded from mrsteam.com All drawings for schematic purposes only. Indicates a potentially hazardous situation, which, if not avoided, may result in death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury or product damage. is used to address practices not related to physical injury. 1 SteamLinx A and B signal range is limited to max. distance of 60ft. Connecting SteamLinx A to the Steam Generator · Disconnect power to the generator at the breaker box. · Locate the SteamLinx A (with the integral cable). To prevent shock hazard, disconnect power at the breaker box before removing generator cover · Remove knock-out. · Remove generator cover. · Route the SteamLinx A cable through the knockout ELECTRICAL SHOCK HAZARD. MrSteam steam generators are connected to 240V line voltage and contain live electrical components. All installation and service must be performed by a licensed and qualified electrician. · Locate the circuit board. · Plug the SteamLinx A into the white connector located at the far left side of the circuit board. · Replace cover and screws. · Restore power. ELECTRICAL SHOCK HAZARD. MrSteam steam generators are connected to 240V line voltage and contain live electrical components. All installation and service must be performed by a licensed and qualified electrician. Generator Cover Circuit Board Cover Screws Knock-out in the Generator Jacket 2 Connecting SteamLinx B to the Home Router · Plug the blue ethernet cable provided, into an ethernet slot on the back of the home router. · Plug the power supply into a Power Supply 120V outlet. Home Router 3' Cable Ethernet Cable (3') 3 Connecting SteamLinx to the Internet · Insure the mobile device is on the WiFi network. · Download the SteamLinx App from the Apple Store or Google Play by following prompts. 4 Troubleshooting: Blinking LED Units are out of range or not paired · Turn breaker off. · Insure SteamLinx A is connected to the steam generator. Troubleshooting: Indicator Lights LEDs Yellow Blinking units are in pairing mode. · Use a paperclip or similar blunt end object to press the reset button (above the LED) on SteamLinx B. · The LED will flash yellow (it stays in pairing mode until it is paired or powered off). · Turn the breaker to the steam generator ON, if the two transmitters are functioning correctly and within range the LEDs will turn blue. Red Router not detected: problem with connections, router configuration or steam generator circuit board. Green SteamLinx B: router is detected but is not connecting to the internet. The indicator light on SteamLinx A will not be illuminated. · If the Blue, Green or Red LEDs are blinking the units are not pairing Blue because they are out of range. Using an extension cord for power, move the SteamLinx B closer to SteamLinx A. Disconnect the ethernet cable (the router connection is not required for this test). If the LEDs stop blinking this confirms the units were out of range. Units are connected correctly. 5 Tech Service Contact 6 Warranty CUSTOMER and TECH SUPPORT Web: Visit mrsteam.com for additional informaton including product specifications, locating a device, sizing calculator, technical downloads and other resources. To view or download the SteamLinx warranty and register, go to blog.mrsteam.com/wr Call: Mon. Fri.: 8 am - 7 pm East Coast: 1.800.767 STEAM (8326) West Coast: 1.800.727 STEAM (8326) Worldwide: 1.718.937.4500 Sussman-Automatic Corporation® I hello@mrsteam.com I www.mrsteam.com 43-20 34th Street, Long Island City, NY 11101 800 76 STEAM PUR 100518 7.19