Antaira Technologies | Industrial Networking Solutions
Antaira Technologies Asia | Industrial Networking Product Solutions
Antaira Technologies PoE Switches, converters and modules, Bluetooth adapters, servers - Antaira Technologies
Installation Guide for antaira models including: LNP-1002C-SFP-24 Series Industrial Unmanaged PoE Switch, LNP-1002C-SFP-24 Series, Industrial Unmanaged PoE Switch, Unmanaged PoE Switch, PoE Switch, Switch
LNP-1002C-SFP-24 - Industrial Unmanaged PoE Switch | Antaira Asia
Resource - Product | Antaira Asia
File Info : application/pdf, 2 Pages, 5.67MB
DocumentDocumentAntaira Technologies LNP-1002C-SFP-24 Series 10-Port Industrial PoE+ Unmanaged Ethernet Switch, w/8*10/100Tx (30W/Port) and 2*Gigabit Combo Ports (2*10/100/1000Tx RJ45 and 2*100/1000 SFP Slots); 12~55VDC Power Input Quick Installation Guide Version 1.0 (March 2022) Package Check List The package contains the following items: 1 Quick installation guide 1 LNP-1002C-SFP-24(-T) 1 Wall mounting bracket set with screws 1 DC cable 18 AWG & DC jack 5.5 x 2.1mm 1 Dust cover set Front Panel Layout 6-Pin Removal Terminal Block (Power Input) Grounding Screw LED for Power 1, Power 2 and Fault Gigabit Combo Port G1~2 100/1000 SFP SFP Fiber Ports G1~2 LED for Link/Activity Status Gigabit Combo Port G1~2 10/100/1000Tx RJ45 LAN# 1~8 10/100Tx RJ45 LAN# 1~8 LED for PoE Status LAN# 1~8 LED for Link/Activity Status 100Mbps LAN# 1~8 LED for Link/Activity Status 10Mbps Top Panel View LNP-1002C-SFP-24 series top panel is equipped with one 6-pin removal terminal block connector for dual DC power inputs (12~55VDC). Grounding Screw Tel: 1-844-268-2472 Fax: 1-714-671-9944 www.antaira.com 19020000000175 6-Pin Removal Terminal Block (Power Input) Product Overview System Interface/Performance · All RJ45 ports support the auto MDI/MDI-X function · Embedded 8*10/100Tx (30W/Port) and 2*Gigabit combo ports (2*10/100/1000Tx RJ45 and 2*100/1000 SFP slots) · Store-and-forward switching architecture · 8K MAC address table · Jumbo frame supports 9.6K Power Input & Connection · DC 12 to 55V redundant power, with a 6-pin removal terminal block · It is recommended to use a UL listed industrial power supply Operating Temperature · Standard operating temperature model: -10°C to 70°C · Extended operating temperature model: -40°C to 75°C Case/Installation · IP30 protection · DIN-Rail and wall mount design LED Indicators LED Power 1 Color Green Power 2 Green Fault Red PoE Indicators (Port 1~8) Green LAN Port 1~8 (Upper LED) Green LAN Port 1~8 (Lower LED) Green SFP Port Combo G1~G2 LINK/ACT Green Amber LAN Port Combo G1~G2 (Upper LED) LAN Port Combo G1~G2 (Lower LED) Green Green Description On Power input 1 is active Off Power input 1 is inactive On Power input 2 is active Off Power input 2 is inactive On Power input 1 or 2 is inactive Off Both power input 1 and 2 are active On The port is supplying power to the powered-device Off No powered-device attached or power supplying fails On Connected to network, 100Mbps Flashing Networking is active Off Not connected to network On Connected to network, 10Mbps Flashing Networking is active Off Not connected to network On Connected to network, 1000Mbps Flashing Networking is active Off Not connected to network On Connected to network, 100Mbps Flashing Networking is active Off Not connected to network On Connected to network, 1000Mbps Flashing Networking is active Off Not connected to network On Connected to network, 10/100Mbps Flashing Networking is active Off Not connected to network Quick Installation Ethernet Ports RJ45 Ports (Auto MDI/MDIX) All RJ45 ports are auto-sensing for 10Base-T, 100Base-TX or 1000Base-T device connections. Please follow the wiring pin assignment table below for Ethernet port installation. Pins Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 RJ45 Ethernet Port Pin Outs T568A Color T568B Color 10Base-T, 100Base-TX white/green stripe white/orange stripe Rx+ green solid orange solid Rx- white/orange stripe blue solid white/blue stripe orange solid white/brown stripe brown solid white/green stripe blue solid white/blue stripe green solid white/brown stripe brown solid Tx+ unused unused Txunused unused 1000 Base-T(X) TP0+ TP0TP1+ TP2+ TP2TP1TP3+ TP3- Power Input Wiring Please follow the steps below to insert the power wire: 1. Insert the positive and negative wires into the PWR1 (V1+, V1-) and PWR2 (V2+, V2-) contacts on the terminal block connector as shown below in Figure 1. 2. Tighten the wire-clamp screws to prevent the wires from loosening, as shown below in Figure 2. Figure 1 Figure 2 Industrial Switch Mounting DIN-Rail Mounting The DIN-Rail bracket is pre-installed on the industrial Ethernet switch from the factory. Please refer to Figure 3 for a DIN-Rail bracket installation reference. Follow the steps below for installing the industrial switch on the DIN-Rail track: 1. Insert the top of the DIN-Rail on to the track as shown below in Figure 4. 2. Lightly pull down the bracket on to the rail as shown below in Figure 5. Figure 3 3. Check if the bracket is mounted tightly on the rail. 4. To remove the industrial Ethernet switch from the rail, do the opposite from the steps above. Figure 4 Figure 5 Wall Mounting Follow the steps below to mount the industrial Ethernet switch using the wall mounting bracket as shown below in Figure 6. 1. Remove the DIN-Rail bracket from the industrial Ethernet switch by loosening the screws. 2. Place the wall mounting brackets on the top and bottom of the industrial Ethernet switch. 3. Use the screws to screw the wall mounting bracket on the industrial Ethernet switch. 4. Use the hook holes at the corners of the wall mounting bracket to hang the industrial Ethernet switch on the wall. 5. To remove the wall mount bracket, do the opposite from the steps above. Figure 6 Field Maintenance and Service If the device requires servicing of any kind, the user is required to disconnect and remove it from its mounting. The initial installation should be done in a way that makes this as convenient as possible. Voltage/power lines should be properly insulated as well as other cables. Be careful when handling them so as to not trip over. Do not under any circumstance insert foreign objects of any kind into the heat dissipation holes located in the different faces of the device. This may not only harm the internal layout, but might cause harm to user as well. Do not under any circumstance open the device for any reason. Please contact your dealer for any repair needed or follow the instructions within the manual. Warranty Policy Warranty Conditions Products supplied by Antaira Technologies are covered in this warranty for sub-standard performance or defective workmanship. The warranty is not, however, extended to goods damaged in the following circumstances: (a) Excessive forces or impacts (b) War or an Act of God: wind storm, fire, flood, electric shock, earthquake (c) Use of unqualified power supply, connectors, or unauthorized parts/kits (d) Replacement with unauthorized parts RMA and Shipping Costs Reimbursement Customers shall always obtain an authorized "RMA" number from Antaira before shipping the goods for repair or replacement. · Within the warranty period (based on the invoice date), all parts and labor are free of charge to the customers. · Customers are responsible for the cost of parts and labor, if the products are out of warranty. · For RMA service, customers are responsible for the shipping expense for shipping the RMA unit(s) to Antaira. Antaira is responsible for the shipping expense via a ground service for the return repair/replace unit(s) back to customers. Limited Liability Antaira would not be held responsible for any consequential losses from using Antaira's product. Warranty Period 5-Year Warranty Antaira's Customer Service and Support · Antaira's Technical Service & Support Centers: + 844-268-2472 (Antaira US Headquarter) + 48-22-862-88-81 (Antaira Europe Office) + 886-2-2218-9733 (Antaira Asia Office) · Antaira's Web Sites & Repair/Support Emails: www.antaira.com / support@antaira.com www.antaira.eu / info@antaira.eu www.antaira.com.tw / info@antaira.com.tw *Any changes will be announced on the Antaira website.