Instruction Manual for SOYAL models including: AR-888H, AR888H, 2ACLEAR-888H, 2ACLEAR888H, AR-888 Series Proximity Controller Reader and Keypad, AR-888 Series, Proximity Controller Reader and Keypad
SOYAL TECHNOLOGY CO., LTD. AR-888H Illuminated LED Frame Access Controller 2ACLEAR-888H 2ACLEAR888H ar 888h
SOYAL® ACCESS CONTROL SYSTEM Contents AR-888 Series 1 Product (US / EU) 2 User Guide 3 Terminal Cables AR-888 4 Tools V150708 5 EVA foam gasket (US/ EU) CN1 CN2 CN4 CN5 CN9 WG-Input RS-485 Duress Flat Head Hex Socket Screw: M3x8 Iron bar*2 Bottom Cover (Inserted into Product) FCC Statement (part15.21,15.105) Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.--Consult the dealer or an experienced radio/TV technician for help. Installation Take off two Iron bars from the of bottom body A and and mounting plate B. Pull the cables from the square holes of the eva foam gasket and mounting plate. Use a screwdriver to screw the eva foam gasket C and mounting plate B onto the wall with Flat Head Cap Philips Tapping Screws (Excluded, the Installer should prepare before installation. The screws shall not be screwed too tight, or it could lead to the deformation of the mounting plate. Connect the cables to the backside of body A and attach A to B . To fix A on B by inserting two Iron bars from the bottom of A + B. Attach the Back Cover D to A. Use the Allen key and screws to assemble the Back Cover onto the body. Hands-off and clear any objects around the 888 (H/K). Turn on the power and LED will light-up and beep will sound. Wait the Touch IC start for 10 sec. to operate. 81 15 Proportion 1:1 Unit: mm 3.3 A. 1 6 D. 7 B. C. 4 (Excluded) In-wall 2 Depth 32mm 5 (Excluded) 3 Cable selection: Use AWG 22-24 Shielded Twist Pair to avoid star wiring. Use CAT5 for TCP/IP connection. (Excluded) 86 118 75 84 Indicators: 1*Bi-Color AR-888 (H/K/U) 3*One Color LED AR-PBI-888 1*Bi-Color Green-Red Green (Optional) White (Stand-By) Red (Optional) Green-Red (Exchangeable) US Mounting Hole: 73x48x40mm(HxWxD) / Screw hole pitch : 84mm Suitable for 70X118 1-module flushmounting box.( Australian, Italy, USA(501E) Standard) EU Mounting Hole: 57x53x40mm(HxWxD) / Screw hole pitch: 60mm Suitable for 86X86 flush-mounting box. (UK, Continental Europe, Germany Standard) 51 5.3 Proportion 1:1 Unit: mm 88 13 15 57.6 54.6 13 3.3 8.5 3.3 20 10.4 20.4 60 11.5 www.soyal.com Flush-Mounted Series V150708 Basic Commands Enter program mode 123456 Change program code Input 6-digit PWD twice 09 654321654321 Add Card User (Please list down each User Address and its Card ID) User Range: 00000~03000 M4/M8 Mode 19 00001 00001 M6 Mode (Must set up 17*0000#) 22 1 Ex.: 00001 start user address at 00001 and scanned 50 pcs of card one by one; next time, input 19*00051*00001# Attach/Present Card One by One Add PIN User PIN=0000 (Disable) M4/M8 Mode (4/8 beeps while engtering progrm mode) 12 00001 1234 M6 Mode (6 beeps) 15 1234 Delete Card User User Range: 00000~03000 M4/M8 Mode 10 00001 9 00005 M6 Mode 10 00001 00005 Ex.: 00001 start user address at 00001 00005 end user address at 00001 Totally 5 user cards will be disabled. Delete All User Cards 29 29 Reset to Factory Default Value (Delete all cards and parameters) 29 20 Wiring Diagrams Alarm Output 3-Lift Control Wiring AR-401RO16B Node ID 001 Lift B- Controller Host A+ AR-321L485 B- Converter A+ RX Floor/ Stop SET FFFFFFFF 0 87654321 1 16 15 14 13 12 11 10 9 2 24 23 22 21 20 19 18 17 3 32 31 30 29 28 27 26 25 Ex. Assign user address 1 to access to 1, 3, 5, 7 floor 21*00001*0*01010101# Alarm Output 2- WG Dual Door Control Wiring Lock External Relay N.C. N.O. COM CTL 12V Alarm Output 1- Alarm Wiring Alarm External Relay N.C. N.O. COM CTL 12V N.O. COM N.C. GND DC12V Exit Button Wiring Push Button AR-PBI888 CN1 Door Sensor Wiring Door Contact N.C. Door Lock Wiring Add Card+PIN User PIN=0000 (Disable) M4/M8 Mode 13 00001 M6 Mode 17 4321 4321 Set up Door Relay Time TTT: 001~600=1~600 sec. 601~609=0.1~0.9sec. 000=On/ Off (Latch) 02 007 Set up Door Close Time TTT: 001~600=1~600 sec. 18 015 Exit program mode or Electric Bolt Magnetic Lock Electric Strike WG Reader Wiring AR-888 (K/U) 125kHz WG/ABA/RS232 Format (Change by shorted on PCB) Format WG RST/Bits WG 26 Open Open WG 34 Open Short RS-232 Short Open ABA-8 Short Short ABA-10 Short Open AR-888 (K/U) 13.56MHz WG/ABA Format (Change by wires connection) Format SET 1 SET 2 Note WG 26 Open Open HEX WG 34 Open To GND HEX ABA-10 To GND Open BCD10 ABA-5-5 To GND To GND BCD Set up Node ID Ex. Node 32 connected to PC 00 032 032 032 Ex. Node 9 conected to 716E 00 009 032=Node ID of Access Controller 032=Virtual 716E Node ID 032=Door number (All Range:001~254) 009=Node ID of Access Controller Range: 001~254) Networking Connection Wiring Notice: At every 32 units or at every300M connection to add a RS485 Booster. Suggest to connect up to 32 units for each CH of AR-727CM AR-888(H) Node ID 254 AR-888(H) Node ID 032 AR-888(H) Node ID 002 Enable Life Control 24 002 (Enable) 24 000 (Disable) Assign Users (Single Floor) 27 UUUUU FF UUUUU=User Address=00000~03000 FF=Floor number=1~32 Assign Floor User (Multi-Floor) 21 UUUUU S FFFFFFFF S=Set=0~3 FFFFFFFF=0 (Disable) / 1 (Enable) Occupied Alarm Output to support 28 064 (Enable) 28 128 (Disable) Enable Door Open Too Long Alarm Enable Arming while exit program mode Stop Alarm by Push Button 24 064 (Enable) 24 000 (Disable) POWER 12VDC AR-888 (H) CN9 GND GLED Input (Active High) RLED Input (Active High) Hall-Effect Sensor (Active Low) CN1 CN2 GND DC12V Alarm PB Door SEN. COM WG1 WG0 Buzzer GLED RLED N.C. N.O. GND Duress Arming LA+ Stand-Alone LB- /Networking CN5 CN4 Controller WG Reader AR-888 (K/U) CN1 CN9 GND GLED Input (Active High) RLED Input (Active High) Hall-Effect Sensor (Active Low) GND DC12V Card Present SET1 (Format) SET2 (Format) 13.56MHz LA+ (FW Only) LB- (FW Only) WG RST CN2 WG-Buzzer WG-GLED RLED Reserved WG0 WG1 CN5 CN4 13.56MHz 125kHz Each CH up to 8 Nodes B- CH2 A+ BA+ CH1 BA+ Host Multi-Door Controller Node ID 001 Converter AR-321CM AR-727CM www.soyal.comAdobe PDF Library 10.0.1 Adobe InDesign CS6 (Windows)