Technical Information | i-PRO Products
Instruction Manual for i-PRO models including: WV-QEM501 Ceiling Mount Bracket, WV-QEM501, Ceiling Mount Bracket, Mount Bracket, Bracket
取扱説明書 WV-QEM501-W | i-PRO Products
WV-QEM501-W | i-PRO Products
File Info : application/pdf, 2 Pages, 2.27MB
DocumentDocumentOperating Instructions
Included Installation Instructions
Ceiling Mount Bracket
Model No. WV-QEM501
· Before attempting to connect or install this product, please read these instructions carefully and save this manual for future use.
· The external appearance and other parts shown in this manual may differ from the actual product within the scope that will not interfere with normal use due to improvement of the product.
i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation.
"<Control No.: C****>" used in these documents should be used to search for information on our technical information website (https://i-pro.com/global/en/ surveillance/training-support/support/technical-information) and will guide you to the right information.
i-PRO Co., Ltd.
https://www.i-pro.com/
© i-PRO Co., Ltd. 2022
Ns0522-0 Printed in China
Preface
This product is a ceiling embedded bracket that is designed to mount the network camera on a ceiling. This bracket can be used for an area with weak pull-out strength such as plasterboard in a double ceiling, and the embedded type makes the visible part of the camera smaller.
The latest information about the supported cameras <Control No.:C0501>.
Specifications
Ambient operating temperature: 50 °C to +60 °C {58 °F to +140 °F}
Dimensions:
ø212 mm × 134 mm (H)* {ø8-11/32 inches × 5-9/32 inches}
*Including decorative cover thickness: 13 mm {1/2 inches}
Mass:
Approx. 740 g {1.63 lbs}
Finish:
Main body: Surface treatment steel sheet Decorative cover: ABS resin i-PRO white
Precautions for installation
In order to prevent injury, the product must be securely mounted to the ceiling
according to the Installation Guide of this product.
This product is designed to be used indoors.
This product is not operable outdoors. Do not expose this product to direct sunlight for hours and
do not install the product near a heater or an air conditioner. Otherwise, it may cause deformation,
discoloration and malfunction. Keep this product away from water and moisture.
Installation area for this product
Make sure that the installation area is strong enough to hold the total weight of the camera assembly before installation. The installation area shall have 210 mm {8-9/32 inches} or more space behind the ceiling.
210 mm {8-9/32 inches} or more
The thickness of the ceiling board for installation can range between 9 mm {11/32 inches} and 40 mm {1-9/16 inches}. Make sure to remove this product if it will no longer be used.
Ceiling board: between 9 mm {11/32 inches} and 40 mm {1-9/16 inches}
Standard Accessories
Operating Instructions (this document)....... 1 pc. Safety wire* ............................................... 1 pc. Safety wire angle* ...................................... 1 pc. Fixing screw for attachment plate (M4 x 8 mm)... 5 pcs.
(of them, 1 for spare)
Template A ................................................ 1 pc. Template B ................................................ 1 pc. Decorative cover........................................ 1 pc.
* The product is shipped in a state where the safety wire is attached to the safety wire angle.
Other items that are needed (not included)
Anchor bolt (M10)*....................................2 pcs. Nut (M10) ................................................ 6 pcs. * One anchor is used for securing the mounting chassis, and the other anchor is used for connect-
ing the safety wire. (See Step2)
IMPORTANT
· Prepare anchor bolts according to the material and strength of the area where the product is to be installed. The pull-out strength of the anchor bolt shall be more than 5 times of the total weight of the installed devices (including the camera body, ceiling mount bracket, anchor bolts, and all other parts).
Caution: · Before attempting to connect or operate this
product, please read these instructions carefully.
Notice: · This product is not suitable for use in loca-
tions where children are likely to be present. · Do not install this product in locations where
ordinary persons can easily reach. · For information about screws and other parts
required for installation, refer to the corresponding section of this document.
Precautions
Do not use this bracket except with suitable cameras. Failure to observe this may cause a drop resulting in injury or accidents. Refer installation work to the dealer. Installation work requires technique and experience. Failure to observe this may cause fire, electric shock, injury, or damage to the product. Be sure to consult the dealer. The measures of protection against a fall of this product shall be taken. Failure to observe this may cause a drop resulting in injury or accidents. Be sure to install the safety wire. The screws and bolts must be tightened to the specified torque. Failure to observe this may cause a drop resulting in injury or accidents. Install the product securely on a ceiling in accordance with the installation instructions. Failure to observe this may cause injury or accidents. Do not rub the edges of metal parts with your hand. Failure to observe this may cause injury.
When using this product, also read the "Precautions" described in the operating instructions for the camera to be attached.
Installation
Refer to the operating instructions of the camera for details on the camera installation (including the camera mounting, cable connection and adjustment).
Step 1 Put Template A (accessory) against the ceiling and make a hole.
Make 4 holes of 12 mm {15/32 inches} in diameter.
Remove the central part from the template. Make a hole of 180 mm {7-3/32 inches}
in diameter. The ceiling hole shape is shown in the drawing at right.
ø180 mm {7-3/32 inches}
Ceiling surface
ø12 mm {15/32 inches} (4 positions)
Brand logo side
Template A
Step 2 Install two anchor bolts (M10: locally procured) into the ceiling.
Determine the anchor bolt length (for securing the mounting chassis) by use of Template B
(accessory).
Position the nut (locally procured) by use of Template B and mount the nut. (The distance between the bottom surfaces of the ceiling board and nut shall be 134 mm {5-9/32 inches}.)
Anchor bolt (for connecting the safety wire)
Anchor bolt (for securing the mounting chassis)
1 m {3.28 feet} or less
Mount a nut Determine the anchor bolt length
Template B
134 mm {5-9/32 inches}
Ceiling board
Install the anchor bolt in the center of the hole
IMPORTANT:
· When the existing anchor bolt is used as an anchor bolt for connecting the safety wire, make sure that the distance between the anchor bolt and camera mounting position is 1 m {3.28 feet} or less.
Step 3
Secure the safety wire angle (accessory) to the anchor bolt (for connecting the safety wire), and connect the safety wire (accessory).
Mount a nut so that the safety wire angle is
<Image of safety wire connection>
secured on the anchor bolt.
Remove the safety wire from the safety wire angle. Insert the groove of the portion of the
safety wire angle into the anchor bolt.
Existing anchor bolt
Safety wire
Close the safety wire angle while inserting the groove of the portion of the safety wire angle into the anchor bolt.
Connect the safety wire to the safety wire angle again.
Nut (locally procured)
Anchor bolt
Safety wire angle
Upper side
Engage the nut from beneath, and secure the safety wire angle with top and bottom
Insert
Close
nuts.
Remove
Engage another nut from beneath to
tighten and secure the nut that was
engaged from beneath in y in a double
nut fashion.
Safety wire
Safety wire angle
Lower side
Connect
Note: · When the existing anchor bolt that
has been installed is used for connecting the safety wire, the use of 2 spacer nuts is helpful.
Spacer nuts Safety wire
Spacer nuts Safety wire angle Existing anchor bolt
Step 4 Attach the safety wire.
Attach the safety wire to the mounting chassis as shown in the illustration below.
Fix the hook of the safety wire to this product.
Safety wire (Accessory)
Cables
Roof space
Ceiling board Mounting chassis
Step 8
Connect the cables and mount the camera on the attachment plate. Refer to the installation guide or the installation procedure leaflet of
the camera for connection of cables and for how to fix the camera.
Camera mounting method
Note: · Hold and rotate the camera main body gently to the left to check that the lock plate of the
camera does not come off.
Camera dismounting method Insert a thin flat head screwdriver to the gap between this product and the camera and lift up the
lock plate. Turn the camera to the left in a state while the lock plate is being lifted up.
Lock plate
Step 5 Put the mounting hole of the mounting chassis
on the anchor bolt. To align the i-PRO logo on the decorative
Mounting hole
Direction of brand logo
Hook
Approx. 10°
cover, align the direction of the mounting
(3 places)
chassis before inserting the mounting chassis
into the mounting hole on the ceiling board.
The direction of the i-PRO logo is indicated
by a point that is shifted by around 10° from
a point that is almost the exact opposite
direction of the hook (to be used as the
reference) that fixes the decorative cover.
Hook
Step 6 Secure the mounting chassis.
(to be used as the reference)
Pass the upper side of the mounting chassis through the anchor bolt (for securing the mounting chassis).
Anchor bolt
Anchor bolt
(for connecting the safety wire)
(for securing the mounting chassis)
Secure the mounting chassis to the ceiling board
with the ceiling board fixing screws (4 places).
Turning the ceiling board fixing screws clockwise Double nuts
provides ceiling board tightening between the
(locally procured)
bottom of the mounting chassis and ceiling board fixing bracket resulting in mounting chassis securing.
Ceiling board fixing bracket (4 places)
Recommended tightening torque:
0.78 N·m {0.58 lbf·ft}
IMPORTANT:
· When securing this bracket on the ceiling, make sure that the four ceiling board fixing brackets are open as shown in the right illustration.
Ceiling board
Ceiling board fixing screw
(4 places)
Turn
clockwise
Use double nuts (locally procured) to secure the mounting chassis.
Step 7 Mount the attachment plate.
Mounting chassis
Mount the attachment plate (accessory of the camera) to this mounting chassis. Use fixing screws for attachment plate (M4: accessory) to secure the attachment plate firmly as shown in the right illustration.
Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}
Fixing screw for attachment plate (4 pcs.) (M4: accessory)
Attachment plate (accessory of the camera)
Step 9 Check the camera operation.
Remove the protection film and turn on the power of the camera. Then, check that the camera operation is normal.
Step 10 Mount the decorative cover.
Mount the decorative cover on this mount bracket. · Align the "I" mark of the decorative cover (accessory) with the hook of the mounting chassis,
press the decorative cover against the ceiling, and rotate the decorative cover clockwise when viewing it from beneath to secure the cover.
Hook for the decorative cover (3 places)
Projection
Hook of the mounting chassis
"I" Mark
Projection (3 places)
Decorative cover
WV-QEM501
i-PRO https://i-pro.com/jp/ja/support_portal
<Cxxxx> https://i-pro.com/jp/ja/support_portal/technical_information
i-PRO
https://www.i-pro.com/
C0501
-50 60 212mm 134mm13mm 740g ABSi-PRO
PC
210mm
9mm 40mm
210mm 9mm 40mm
........................................ 1 A.............................................................. 1 ........................................ 1 B.............................................................. 1 ........................ 1 ..................................................... 1 M4×8mm... 5
1
M10............................ 2 M10.............................................. 6
1 1 Step2
5
Step1 A
12mm4 180mm
ø180mm
ø12mm 4
A
Step2 M102
B
B
134mm
1m
1m
B
134mm
Step3
-
2
-
Step4
Step7
M4
0.78N·m{8kgf·cm}
4 M4
Step8
Step5
i-PRO
3
10°
180°10°
i-PRO
Step9
Step10
I
Step6
4
0.78N·m{8kgf·cm}
4
4
4
- 3
3