Mitsubishi Electric Split-Type Air Conditioners

Safety Precautions

WARNING: This unit uses a flammable refrigerant. If refrigerant leaks and comes in contact with fire or heating part, it will create harmful gas and there is risk of fire.

Read the OPERATING INSTRUCTIONS carefully before operation.

Service personnel are required to carefully read the OPERATING INSTRUCTIONS and INSTALLATION MANUAL before operation.

i Further information is available in the OPERATING INSTRUCTIONS, INSTALLATION MANUAL, and the like.

Since rotating parts and parts which could cause an electric shock are used in this product, be sure to read these "Safety Precautions" before use.

Since the cautionary items shown here are important for safety, be sure to observe them.

After reading this manual, keep it together with the installation manual in a handy place for easy reference.

Marks and their meanings

WARNING: Incorrect handling could cause serious hazard, such as death, serious injury, etc. with a high probability.

CAUTION: Incorrect handling could cause serious hazard depending on the conditions.

Meanings of symbols used in this manual

• ☑ Be sure not to do.
• ✔ Be sure to follow the instruction.
• Never insert your finger or stick, etc.
• Never step onto the indoor/outdoor unit and do not put anything on them.
• Danger of electric shock. Be careful.
• Be sure to disconnect the power supply plug from the power outlet.
• Be sure to shut off the power.
• Risk of fire.
• Never touch with wet hand.
• Never splash water on the unit.

WARNING

Do not connect the power cord to an intermediate point, use an extension cord, or connect multiple devices to a single AC outlet. This may cause overheating, fire, or electric shock.

Make sure the power plug is free of dirt and insert it securely into the outlet. A dirty plug may cause fire or electric shock.

Do not bundle, pull, damage, or modify the power cord, and do not apply heat or place heavy objects on it. This may cause fire or electric shock.

Do not turn the breaker OFF/ON or disconnect/connect the power plug during operation. This may create sparks, which can cause fire.

After the indoor unit is switched OFF with the remote controller, make sure to turn the breaker OFF or disconnect the power plug.

Do not expose your body directly to cool air for a prolonged length of time. This could be detrimental to your health.

The unit should not be installed, relocated, disassembled, altered, or repaired by the user. An improperly handled air conditioner may cause fire, electric shock, injury, or water leakage, etc. Consult your dealer.

If the power supply cord is damaged, it must be replaced by the manufacturer or its service agent in order to avoid a hazard.

When installing, relocating, or servicing the unit, make sure that no substance other than the specified refrigerant (R32) enters the refrigerant circuit. Any presence of foreign substance such as air can cause abnormal pressure rise and may result in explosion or injury.

The use of any refrigerant other than that specified for the system will cause mechanical failure, system malfunction, or unit breakdown. In the worst case, this could lead to a serious impediment to securing product safety.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

Do not insert your finger, a stick, or other objects into the air inlet or outlet. This may cause injury, since the fan inside rotates at high speeds during operation.

In case of an abnormal condition (such as a burning smell), stop the air conditioner and disconnect the power plug or turn the breaker OFF. A continued operation in the abnormal state may cause a malfunction, fire, or electric shock. In this case, consult your dealer.

When the air conditioner does not cool or heat, there is a possibility of refrigerant leakage. If any refrigerant leakage is found, stop operations and ventilate the room well and consult your dealer immediately. If a repair involves recharging the unit with refrigerant, ask the service technician for details.

The refrigerant used in the air conditioner is not harmful. Normally, it does not leak. However, if refrigerant leaks and comes in contact with fire or heating part of such a fan heater, kerosene heater, or cooking stove, it will create harmful gas and there is risk of fire.

The user should never attempt to wash the inside of the indoor unit. Should the inside of the unit require cleaning, contact your dealer. Unsuitable detergent may cause damage to plastic material inside the unit, which may result in water leakage. Should detergent come in contact with electrical parts or the motor, it will result in a malfunction, smoke, or fire.

The appliance shall be stored in a room without continuously operating ignition sources (for example: open flames, an operating gas appliance or an operating electric heater). Be aware that refrigerants may not contain an odour.

Do not use means to accelerate the defrosting process or to clean the appliance, other than those recommended by the manufacturer. Do not pierce or burn.

The indoor unit must be installed in rooms which exceed the floor space specified. Please consult your dealer. AP50: 1.7 m²

This appliance is intended to be used by expert or trained users in shops, in light industry and on farms, or for commercial use by lay persons.

CAUTION

Do not touch the air inlet or the aluminum fins of the indoor/outdoor unit. This may cause injury.

Do not use insecticides or flammable sprays on the unit. This may cause a fire or deformation of the unit.

Do not expose pets or houseplants to direct airflow. This may cause injury to the pets or plants.

Do not place other electric appliances or furniture under the indoor/outdoor unit. Water may drip down from the unit, which may cause damage or malfunction.

Do not leave the unit on a damaged installation stand. The unit may fall and cause injury.

Do not step on an unstable bench to operate or clean the unit. This may cause injury if you fall down.

Do not pull the power cord. This may cause a portion of the core wire to break, which may cause overheating or fire.

Do not charge or disassemble the batteries, and do not throw them into a fire. This may cause the batteries to leak, or cause a fire or explosion.

Do not operate the unit for more than 4 hours at high humidity (80% RH or more) and/or with windows or outside door left open. This may cause water condensation in the air conditioner, which may drip down, wetting or damaging the furniture. The water condensation in the air conditioner may contribute to growth of fungi, such as mold.

Do not use the unit for special purposes, such as storing food, raising animals, growing plants, or preserving precision devices or art objects. This may cause deterioration of quality, or harm to animals and plants.

Do not expose combustion appliances to direct airflow. This may cause incomplete combustion.

Never put batteries in your mouth for any reason to avoid accidental ingestion. Battery ingestion may cause choking and/or poisoning.

Before cleaning the unit, switch it OFF and disconnect the power plug or turn the breaker OFF. This may cause injury, since the fan inside rotates at high speeds during operation.

When the unit will be unused for a long time, disconnect the power plug or turn the breaker OFF. The unit may accumulate dirt, which may cause overheating or fire.

Replace all batteries of the remote controller with new ones of the same type. Using an old battery together with a new one may cause overheating, leakage, or explosion.

If the battery fluid comes in contact with your skin or clothes, wash them thoroughly with clean water. If the battery fluid comes in contact with your eyes, wash them thoroughly with clean water and immediately seek medical attention.

Ensure that the area is well-ventilated when the unit is operated together with a combustion appliance. Inadequate ventilation may cause oxygen starvation.

Turn the breaker OFF when you hear thunder and there is a possibility of a lightning strike. The unit may be damaged if lightning strikes.

After the air conditioner is used for several seasons, perform inspection and maintenance in addition to normal cleaning. Dirt or dust in the unit may create an unpleasant odor, contribute to growth of fungi, such as mold, or clog the drain passage, and cause water to leak from the indoor unit. Consult your dealer for inspection and maintenance, which require specialized knowledge and skills.

Do not operate switches with wet hands. This may cause electric shock.

Do not clean the air conditioner with water or place an object that contains water, such as a flower vase, on it. This may cause fire or electric shock.

Do not step on or place any object on the outdoor unit. This may cause injury if you or the object falls down.

● IMPORTANT

Dirty filters cause condensation in the air conditioner which will contribute to the growth of fungi such as mold. It is therefore recommended to clean air filters every 2 weeks.

Before starting the operation, ensure that the horizontal vanes are in the closed position. If operation starts when the horizontal vanes are in the open position, they may not return to the correct position.

Name of Each Part

Indoor unit

Front panel

Air filter

Air cleaning filter (V Blocking Filter)

Horizontal vane

Heat exchanger

Fan guard

Air outlet

Air inlet

Operation indicator lamp

Remote control receiving section

Wi-Fi interface (See page 13)

Spec name plate *1

Outdoor unit

Air inlet (back and side)

Spec name plate *1

Refrigerant piping

Drainage hose

Air outlet

Drain outlet

*1 The manufacturing year and month are indicated on the spec name plate.

Outdoor units may be different in appearance.

Remote controller

Battery replacement indicator (See page 5)

Operation display section

Emergency operation switch (See page 11)

Temperature buttons (See page 6)

Operation select button (See page 6)

ECONO COOL button (See page 8)

i-save button (See page 8)

NIGHT MODE button (See page 9)

CLOCK button (See page 5)

Signal transmitting section (Distance of signal: About 6 m. Beep(s) is (are) heard from the indoor unit when the signal is received.)

OFF/ON (stop/operate) button

FAN speed control button (See page 7)

WIDE VANE button (See page 7)

VANE control button (See page 7)

TIME, TIMER set buttons (See pages 5, 9)

forward button

backward button

WEEKLY TIMER set buttons (See pages 5, 10)

SET CANCEL

DAY

1~4

ON/OFF

TIME

TEMP

DELETE

CLOCK RESET

RESET button (See page 5)

Lid: Slide the lid down to open the remote controller. Slide it down further to get to the weekly timer buttons.

Remote controller usage notes:

• Only use the remote controller provided with the unit.
• Do not use other remote controllers.
• If 2 or more indoor units are installed in proximity to one another, an indoor unit that is not intended to be operated may respond to the remote controller.

Preparation Before Operation

Installing the remote controller batteries

1. Remove the front lid.
2. Insert the negative pole of AAA alkaline batteries first.
3. Install the front lid.

Notes:

• Make sure the polarity of the batteries is correct.
• Do not use manganese batteries and leaking batteries. The remote controller could malfunction.
• Do not use rechargeable batteries.
• The battery replacement indicator lights up when the battery is running low. In about 7 days after the indicator starts lighting up, the remote controller stops working.
• Replace all batteries with new ones of the same type.
• Batteries can be used for approximately 1 year. However, batteries with expired shelf lives last shorter.
• Press RESET gently using a thin instrument. If the RESET button is not pressed, the remote controller may not operate correctly.

Setting current time

1. Press CLOCK.
2. Press either the TIME button or the TIMER buttons to set the time. Each press changes the clock 1 minute forward/backward (10 minutes when pressed longer).
3. Press CLOCK again.
4. Press the DAY button to set the day.

Note: Press CLOCK gently using a thin instrument.

How to set remote controller exclusively for a particular indoor unit

A maximum of 4 indoor units with wireless remote controllers can be used in a room.

To operate the indoor units individually with each remote controller, assign a number to each remote controller according to the number of the indoor unit. This setting can be set only when all the following conditions are met:

• The remote controller is powered OFF.

1. Hold down 1~4 button on the remote controller for 2 seconds to enter the pairing mode.
2. Press 1~4 button again and assign a number to each remote controller. Each press of 1~4 button advances the number in the following order: 1 → 2 → 3 → 4.
3. Press SET button to complete the pairing setting.

After you turn the breaker ON, the remote controller that first sends a signal to an indoor unit will be regarded as the remote controller for the indoor unit. Once they are set, the indoor unit will only receive the signal from the assigned remote controller afterwards.

Selecting Operation Modes

DRY mode: Dehumidify your room. The room may be cooled slightly. Temperature cannot be set during DRY mode.

HEAT mode: Enjoy warm air at your desired temperature.

FAN mode: Circulate the air in your room.

Note: After COOL/DRY mode operation, it is recommended to operate in the FAN mode to dry inside the indoor unit.

Multi system operation: Two or more indoor units can be operated by one outdoor unit. When several indoor units are operated simultaneously, cooling/dry/fan and heating operations cannot be done at the same time. When COOL/DRY/FAN is selected with one unit and HEAT with another or vice versa, the unit selected last goes into standby mode.

Operation indicator lamp

The operation indicator lamp shows the operation state of the unit.

AUTO mode (Auto change over): The unit selects the operation mode according to the difference between the room temperature and the set temperature. During AUTO mode, the unit changes mode (COOL ↔ HEAT) when the room temperature is about 2°C away from the set temperature for more than 15 minutes.

Note: Auto Mode is not recommended if this indoor unit is connected to a MXZ type outdoor unit. When several indoor units are operated simultaneously, the unit may not be able to switch operation mode between COOL and HEAT. In this case, the indoor unit becomes standby mode (Refer to table of Operation indicator lamp).

COOL mode: Enjoy cool air at your desired temperature.

Note: Do not operate COOL mode at very low outside temperatures (less than -10°C). Water condensed in the unit may drip and wet or damage furniture, etc.

Operation steps:

1. Press OFF/ON to start the operation.
2. Press MODE to select operation mode. Each press changes mode in the following order: (AUTO) → (COOL) → (DRY) → (HEAT) → (FAN)
3. Press Δ or ∇ to set the temperature. Each press raises or lowers the temperature by 1°C.
4. Press OFF/ON to stop the operation.

Fan Speed and Airflow Direction Adjustment

Fan speed

Press FAN to select fan speed. Each press changes fan speed in the following order:

(AUTO) → (Silent) → (Low) → (Med.) → (High) → (Super High)

Notes:

• Two short beeps are heard from the indoor unit when set to AUTO.
• Use higher fan speed to cool/heat the room quicker. It is recommended to lower the fan speed once the room is cool/warm.
• Use lower fan speed for quiet operation.

Multi system operation: When several indoor units are operated simultaneously by one outdoor unit for heating operation, the temperature of the airflow may be low. In this case, it is recommended to set the fan speed to AUTO.

Up-down Airflow direction

Press VANE to select airflow direction. Each press changes airflow direction in the following order:

(AUTO) → (1) → (2) → (3) → (4) → (5) → (SWING)

Notes:

• (AUTO): The vane is set to the most efficient airflow direction. COOL/DRY/FAN: horizontal position. HEAT: position (4).
• (Manual): For efficient air conditioning, select the upper position for COOL/DRY, and the lower position for HEAT. If the lower position is selected during COOL/DRY, the vane automatically moves to the upward position after 0.5 to 1 hour to prevent any condensation from dripping.
• (Swing): The vane moves up and down intermittently.
• Two short beeps are heard from the indoor unit when set to AUTO.
• Always use the remote controller when changing the direction of airflow. Moving the horizontal vanes with your hands causes them to malfunction.
• When the breaker is turned on, the horizontal vanes' position will be reset in about a minute, then the operation will start. The same is true in the emergency cooling operation.
• When the horizontal vanes seem to be in an abnormal position, see page 14.

Left-right Airflow direction

Press WIDE VANE to select airflow direction. Each press changes airflow direction in the following order:

(SWING)

I-SAVE OPERATION

A simplified set back function enables to recall the preferred (preset) setting with a single push of the i-save button. Press the button again and you can go back to the previous setting in an instance.

1. Press i-save during COOL, ECONO COOL, HEAT mode or NIGHT MODE operation to select i-save mode.
2. Set the temperature, fan speed, and airflow direction. The same setting is selected from the next time by simply pressing i-save.
• Two settings can be saved. (One for COOL/ECONO COOL, one for HEAT)
• Select the appropriate temperature, fan speed, and airflow direction according to your room.
3. Press i-save again to cancel i-save operation.
4. i-save operation also is cancelled when the MODE button is pressed.

Note:

• Example of use:
• 1. Low energy mode: Set the temperature 2°C to 3°C warmer in COOL and cooler in HEAT mode. This setting is suitable for unoccupied room, and while you are sleeping.
• 2. Saving frequently used settings: Save your preferred setting for COOL, ECONO COOL, HEAT mode and NIGHT MODE operation. This enables you to select your preferred setting with a single push of the button.

ECONO COOL OPERATION

Swing airflow (change of airflow) makes you feel cooler than stationary airflow.

The set temperature and the airflow direction are automatically changed by the microprocessor. It is possible to perform cooling operation while keeping comfort. As a result energy can be saved.

1. Press ECONO COOL during COOL mode (See page 6) to start ECONO COOL operation. The unit performs swing operation vertically in various cycles according to the temperature airflow.
2. Press ECONO COOL again to cancel ECONO COOL operation.
3. ECONO COOL operation is also cancelled when the VANE button is pressed.

NIGHT MODE OPERATION

NIGHT MODE operation changes the brightness of the operation indicator, disables the beep sound and limits the noise level of the outdoor unit.

1. Press NIGHT MODE during operation to activate NIGHT MODE operation.
• The operation indicator lamp dims.
• The beep sound will be disabled except that emitted when the operation is started or stopped.
• Noise level of the outdoor unit will be lower than that mentioned in SPECIFICATIONS.
2. Press NIGHT MODE again to cancel NIGHT MODE operation.

Notes:

• The cooling/heating capacity may drop.
• Noise level of the outdoor unit may not change after start-up of the unit, during the protection operation, or depending on other operating conditions.
• The fan speed of the indoor unit will not change.
• The operation indicator lamp will be hard to be seen in a bright room.
• Noise level of the outdoor unit will not decrease during Multi system operation.

TIMER OPERATION (ON/OFF TIMER)

1. Press ON/OFF (ON timer) or OFF (OFF timer) during operation to set the timer. ON (ON timer): The unit turns ON at the set time. OFF (OFF timer): The unit turns OFF at the set time.
2. ON or OFF blinks. Make sure that the current time and day are set correctly (See page 5).
3. Press < (forward) and > (backward) to set the time of timer. Each press changes the set time 10 minutes forward/backward. Set the timer while ON or OFF is blinking.
4. Press ON/OFF again to cancel timer.

Notes:

• ON and OFF timers can be set together. A mark indicates the order of timer operations.
• If power failure occurs while ON/OFF timer is set, see page 11 "Auto restart function".

WEEKLY TIMER OPERATION

A maximum of 4 ON or OFF timers can be set for individual days of the week. A maximum of 28 ON or OFF timers can be set for a week.

Example: Runs at 24°C from waking up to leaving home, and runs at 27°C from getting home to going to bed on weekdays. Runs at 27°C from waking up late to going bed early on weekends.

Setting the weekly timer

1. Make sure that the current time and day are set correctly.
2. Press SET to enter the weekly timer setting mode. SET blinks.
3. Press DAY and 1~4 to select setting day and number.
4. Press ON/OFF, TIME, and TEMP to set ON/OFF, time, and temperature.
• Pressing (ON/OFF) selects ON/OFF timer.
• Pressing TIME adjusts the time.
• Pressing TEMP adjusts the temperature.
• Pressing DELETE deletes timer setting.
5. Hold down the button to change the time quickly.
6. Press DAY and 1~4 to continue setting the timer for other days and/or numbers.
7. Press SET to complete and transmit the weekly timer setting. Point the remote controller toward the indoor unit for 3 seconds.
• When setting the timer for more than one day of the week or one number, EDIT/SEND does not have to be pressed per each setting. Press SET once after all the settings are complete. All the weekly timer settings will be saved.
• Press SET to enter the weekly timer setting mode, and press and hold DELETE for 5 seconds to erase all weekly timer settings. Point the remote controller toward the indoor unit.
8. Press ON/OFF TIMER to turn the weekly timer ON. (WEEKLY lights.) When the weekly timer is ON, the day of the week whose timer setting is complete, will light.
9. Press ON/OFF TIMER again to turn the weekly timer OFF. (WEEKLY goes out.)

Notes:

• The simple ON/OFF timer setting is available while the weekly timer is on. In this case, the ON/OFF timer has priority over the weekly timer; the weekly timer operation will start again after the simple ON/OFF timer is complete.
• The saved settings will not be cleared when the weekly timer is turned OFF.

Checking weekly timer setting

1. Press SET to enter the weekly timer setting mode.
2. Press DAY and 1~4 to select setting day and number.
3. Press DAY or 1~4 to view the setting of the particular day or number.
4. Press CANCEL to exit the weekly timer setting.

Notes:

• When all days of the week are selected to view the settings and a different setting is included among them, ------ will be displayed.

EMERGENCY OPERATION

When the remote controller cannot be used...

Emergency operation can be activated by pressing the emergency operation switch (E.O. SW) on the indoor unit.

Each time the E.O. SW is pressed, the operation changes in the following order:

Operation indicator lamp → Emergency COOL → Emergency HEAT → Stop

Set temperature: 24°C

Fan speed: Medium

Horizontal vane: Auto

Notes:

• The first 30 minutes of operation is test run. Temperature control does not work, and fan speed is set to High.
• In the emergency heating operation, the fan speed gradually rises to blow out warm air.
• In the emergency cooling operation, the horizontal vanes' position will be reset in about a minute, then the operation will start.

Auto Restart Function

If a power failure occurs or the main power is turned off during operation, "Auto restart function" automatically starts operation in the same mode as the one set with the remote controller just before the shutoff of the main power. When timer is set, timer setting is cancelled and the unit starts operation when power is resumed.

If you do not want to use this function, please consult the service representative because the setting of the unit needs to be changed.

Cleaning

Instructions:

• Switch off the power supply or turn off the breaker before cleaning.
• Be careful not to touch the metal parts with your hands.
• Do not use benzine, thinner, polishing powder, or insecticide.
• When dirt stands out, wash it with kitchen neutral detergent diluted with lukewarm water to the specified concentration, then wipe off the detergent with a damp towel.
• Do not use a scrubbing brush, a hard sponge, or the like.
• Do not soak or rinse the horizontal vane.
• Do not use water hotter than 50°C.
• Do not expose parts to direct sunlight, heat, or fire to dry.
• Do not apply excessive force on the fan as it may cause cracks or breakage.

Air filter (Air purifying filter)

Clean every 2 weeks

Remove dirt by a vacuum cleaner, or rinse with water. After washing with water, dry it well in shade.

Air cleaning filter (V Blocking Filter)

Every 3 months: Remove dirt by a vacuum cleaner. When dirt cannot be removed by vacuum cleaning: Soak the filter and its frame in lukewarm water before rinsing it. After washing, dry it well in shade. Install all tabs of the air filter.

Every year: Replace it with a new air cleaning filter for best performance.

Parts Number: MAC-2470FT-E

Front panel

1. Lift the front panel until a "click" is heard.
2. Hold the hinges and pull to remove as shown in the illustration above. Wipe with a soft dry cloth or rinse it with water. Do not soak it in water for more than two hours. Dry it well in shade before installing it.
3. Install the front panel by following the removal procedure in reverse. Close the front panel securely and press the positions indicated by the arrows.

Important

Clean the filters regularly for best performance and to reduce power consumption. Dirty filters cause condensation in the air conditioner which will contribute to the growth of fungi such as mold. It is therefore recommended to clean air filters every 2 weeks.

Information based on REGULATION (EU) No 528/2012

Wi-Fi INTERFACE SETTING UP (VGK type only)

This Wi-Fi interface communicates the status information and controls the commands from the MELCloud by connecting to the indoor unit.

1. Open the front panel and remove the Wi-Fi interface.
2. Set up a connection between the Wi-Fi interface and the Router. Refer to the SETUP MANUAL and SETUP QUICK REFERENCE GUIDE provided with the unit.
3. For SETUP MANUAL, please go to the website below: http://www.melcloud.com/Support
4. Put the Wi-Fi interface back and close the front panel after the setup is completed.
5. For MELCloud User Manual, please go to the website below: http://www.melcloud.com/Support

Wi-Fi interface introduction

Notes:

• Ensure that the Router supports the WPA2-AES encryption setting before starting the Wi-Fi interface setup.
• The End user should read and accept the terms and conditions of the Wi-Fi service before using this Wi-Fi interface.
• To complete connection of this Wi-Fi interface to the Wi-Fi service, the Router may be required.
• This Wi-Fi interface will not commence transmission of any operational data from the system until the End user registers and accepts the terms and conditions of the Wi-Fi service.
• This Wi-Fi interface should not be installed and connected to any Mitsubishi Electric system which is to provide application critical cooling or heating.
• Please write down the information regarding the Wi-Fi interface setting on the last page of this manual, when you set up this Wi-Fi interface.
• At the time of relocation or disposal, reset the Wi-Fi interface to the factory default.

(1) MODE switch: The MODE switch is used for selecting modes in configurations.

(2) RESET switch: Hold down the RESET switch for 2 seconds to reboot the system. Hold down the RESET switch for 14 seconds to initialize the Wi-Fi interface to the factory default.

When the Wi-Fi interface is reset to the factory default, ALL the configuration information will be lost. Take great care in implementing this operation.

Mitsubishi Electric's Wi-Fi interface is designed for communication to Mitsubishi Electric's MELCloud Wi-Fi service. Third party Wi-Fi interfaces cannot be connected to MELCloud. Mitsubishi Electric is not responsible for any (i) underperformance of a system or any product; (ii) system or product fault; or (iii) loss or damage to any system or product; which is caused by or arises from connection to and/or use of any third party Wi-Fi interface or any third party Wi-Fi service with Mitsubishi Electric equipment.

For the latest information regarding MELCloud from Mitsubishi Electric Corporation, please visit www.melcloud.com.

When You Think That Trouble Has Occurred

Even if these items are checked, when the unit does not recover from the trouble, stop using the air conditioner and consult your dealer.

Indoor Unit

Outdoor Unit

Remote controller

Wi-Fi interface

In the following cases, stop using the air conditioner and consult your dealer.

• When water leaks or drips from the indoor unit.
• When the operation indicator lamp blinks.
• When the breaker trips frequently.
• The remote control signal is not received in a room where an electronic ON/OFF type fluorescent lamp (inverter-type fluorescent lamp, etc.) is used.
• Operation of the air conditioner interferes with radio or TV reception. An amplifier may be required for the affected device.
• When an abnormal sound is heard.
• When any refrigerant leakage is found.

When the Air Conditioner Is Not Going to Be Used for a Long Time

1. Operate by COOL mode with the highest temperature set or FAN mode for 3 to 4 hours. (See page 6) This dries the inside of the unit.
• Moisture in the air conditioner contributes to favorable conditions for growth of fungi, such as mold.
2. Press OFF/ON to stop the operation.
3. Turn off the breaker and/or disconnect the power supply plug.
4. Remove all batteries from the remote controller.

When using the air conditioner again:

1. Clean the air filter. (See page 12)
2. Check that the air inlet and outlet of the indoor and outdoor units are not blocked.
3. Check that the earth is connected correctly.
4. Refer to the "PREPARATION BEFORE OPERATION", and follow the instructions. (See page 5)

INSTALLATION PLACE AND ELECTRICAL WORK

Installation place

Avoid installing the air conditioner in the following places.

• Where there is much machine oil.
• Salty places such as the seaside.
• Where sulfide gas is generated such as hot spring, sewage, waste water.
• Where oil is splashed or where the area is filled with oily smoke (such as cooking areas and factories, in which the properties of plastic could be changed and damaged).
• Where there is high-frequency or wireless equipment.
• Where the air from the outdoor unit air outlet is blocked.
• Where the operation sound or air from the outdoor unit bothers the house next door.

The mounting height of indoor unit 1.8 m to 2.3 m is recommended. If it is impossible, please consult your dealer.

Do not operate the air conditioner during interior construction and finishing work, or while waxing the floor. Before operating the air conditioner, ventilate the room well after such work is performed. Otherwise, it may cause volatile elements to adhere inside the air conditioner, resulting in water leakage or scattering of dew.

For Wi-Fi interface

• Do not use the Wi-Fi interface nearby the medical electrical equipment or people who have a medical device such as a cardiac pacemaker or an implantable cardioverter-defibrillator. It can cause an accident due to malfunctions of the medical equipment or device.
• This equipment should be installed and operated with a minimum distance of 20 cm between the device and the user or bystanders.
• Do not use the Wi-Fi interface nearby other wireless devices, microwaves, cordless phones, or facsimiles. It can cause malfunctions.

To prevent the effects of a fluorescent lamp, keep as far apart as possible. (1 m or more)

Inverter-type fluorescent lamp

Keep a space to prevent the picture distortion or the noise.

The installation location of the outdoor unit should be at least 3 m away from the antennas for TV sets, radios, etc. In areas where the reception is weak, provide greater space between the outdoor unit and the antenna of the affected device if operation of the air conditioner interferes with radio or TV reception.

For the optimum efficiency and to extend the life time of using, the outdoor unit should be installed in a well-ventilated dry place.

100 mm or more

wall, etc.

1 m or more

Cordless TV phone or Portable phone Radio

3 m or more

200 mm or more

Electrical work

Provide an exclusive circuit for the power supply of the air conditioner. Be sure to observe the breaker capacity.

If you have any questions, consult your dealer.

SPECIFICATIONS

* Refer to the spec name plate for the unit weight.

Guaranteed operating range

DB: Dry Bulb

WB: Wet Bulb

Wi-Fi interface

For Declaration of Conformity, please go to the website below: http://www.mitsubishielectric.com/ldg/ibim/

Wi-Fi interface setting information

MEMO

Indoor unit model name:

Indoor unit serial number:

Outdoor unit model name:

Outdoor unit serial number:

Wi-Fi interface MAC address (MAC):

Wi-Fi interface serial number (ID):

Wi-Fi interface PIN (PIN):

Wi-Fi interface SSID (SSID):

Wi-Fi interface KEY (KEY):

System commissioning date:

Wi-Fi interface installation date:

Installer contact details

Name:

Telephone number:

Name of Importer:

Mitsubishi Electric Europe B.V.
Capronilaan 46, 1119 NS, Schiphol Rijk, The Netherlands

French Branch
2, Rue De L'Union, 92565 RUEIL MAISON Cedex

German Branch
Mitsubishi-Electric-Platz 1 40882 Ratingen North Rhine-Westphalia Germany

Belgian Branch
8210 Loppem, Autobaan 2, Belgium

Irish Branch
Westgate Business Park, Ballymount Road, Upper Ballymount, Dublin 24, Ireland

Italian Branch
Palazzo Sirio Ingresso 1, Viale Colleoni, 7, 20864 Agrate Brianza (MI), Italy

Norwegian Branch
Gneisveien 2D, 1914 Ytre Enebakk, Norway

Portuguese Branch
Avda. do Forte 10, 2794-019 Carnaxide, Lisbon, Portugal

Spanish Branch
Av. Castilla, 2 Parque Empresarial San Fernando - Ed. Europa, 28830 San Fernando de Henares (Madrid), Spain

Scandinavian Branch
Hammarbacken 14, P.O. Box 750, SE-19127, Sollentuna, Sweden

UK Branch
Travellers Lane, Hatfield, Hertfordshire, AL10 8XB. England, UK

Polish Branch
Krakowska 48, PL-32-083 Balice, Poland

MITSUBISHI ELECTRIC TURKEY ELEKTRİK ÜRÜNLERİ A.Ş
Şerifali Mahallesi Kale Sokak No: 41 34775 Ümraniye, İstanbul, Turkey

UK DECLARATION OF CONFORMITY

MITSUBISHI ELECTRIC AIR CONDITIONING SYSTEMS MANUFACTURING TURKEY JOINT STOCK COMPANY.
Manisa OSB 4.Kisim Kecilikoyosb Mah.
Ahmet Nazif Zorlu Bulvari No:19 Yunusemre - Manisa.

hereby declares under its sole responsibility that the air conditioners and heat pumps described below for use in residential, commercial and light-industrial environments:

MITSUBISHI ELECTRIC, MSZ-AP25VG/MUZ-AP25VG, MSZ-AP25VG/MUZ-AP25VGH
MSZ-AP35VG/MUZ-AP35VG, MSZ-AP35VG/MUZ-AP35VGH
MSZ-AP42VG/MUZ-AP42VG, MSZ-AP42VG/MUZ-AP42VGH
MSZ-AP50VG/MUZ-AP50VG, MSZ-AP50VG/MUZ-AP50VGH

Note: Its serial number is on the nameplate of the product.

Legislation

• The Electrical Equipment (Safety) Regulations 2016
• The Supply of Machinery (Safety) Regulations 2008
• Electromagnetic Compatibility Regulations 2016
• The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012

Issued: TURKEY 7 January, 2021 Selin Dömekeli Manager, Quality Assurance Department

UK DECLARATION OF CONFORMITY

MITSUBISHI ELECTRIC AIR CONDITIONING SYSTEMS MANUFACTURING TURKEY JOINT STOCK COMPANY.
Manisa OSB 4.Kisim Kecilikoyosb Mah.
Ahmet Nazif Zorlu Bulvari No:19 Yunusemre - Manisa.

hereby declares under its sole responsibility that the air conditioners and heat pumps described below for use in residential, commercial and light-industrial environments:

MITSUBISHI ELECTRIC, MSZ-AP25VGK/MUZ-AP25VG, MSZ-AP25VGK/MUZ-AP25VGH
MSZ-AP35VGK/MUZ-AP35VG, MSZ-AP35VGK/MUZ-AP35VGH
MSZ-AP42VGK/MUZ-AP42VG, MSZ-AP42VGK/MUZ-AP42VGH
MSZ-AP50VGK/MUZ-AP50VG, MSZ-AP50VGK/MUZ-AP50VGH

Note: Its serial number is on the nameplate of the product.

Legislation

• Radio Equipment Regulations 2017
• The Supply of Machinery (Safety) Regulations 2008
• The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012

Issued: TURKEY 7 January, 2021 Selin Dömekeli Manager, Quality Assurance Department

EC DECLARATION OF CONFORMITY

MITSUBISHI ELECTRIC AIR CONDITIONING SYSTEMS MANUFACTURING TURKEY JOINT STOCK COMPANY.
Manisa OSB 4.Kisim Kecilikoyosb Mah.
Ahmet Nazif Zorlu Bulvari No:19 Yunusemre - Manisa.

hereby declares under its sole responsibility that the air conditioners and heat pumps described below for use in residential, commercial and light-industrial environments:

MITSUBISHI ELECTRIC, MSZ-AP25VG/MUZ-AP25VG, MSZ-AP25VG/MUZ-AP25VGH
MSZ-AP35VG/MUZ-AP35VG, MSZ-AP35VG/MUZ-AP35VGH
MSZ-AP42VG/MUZ-AP42VG, MSZ-AP42VG/MUZ-AP42VGH
MSZ-AP50VG/MUZ-AP50VG, MSZ-AP50VG/MUZ-AP50VGH

Note: Its serial number is on the nameplate of the product.

Directives

• 2014/35/EU: Low Voltage Directive
• 2006/42/EC: Machinery Directive
• 2014/30/EU: Electromagnetic Compatibility Directive
• 2011/65/EU, (EU) 2015/863 and (EU) 2017/2102: RoHS Directive

Issued: TURKEY 1 November, 2017 Selin Dömekeli Quality Assurance Department

EC DECLARATION OF CONFORMITY

MITSUBISHI ELECTRIC AIR CONDITIONING SYSTEMS MANUFACTURING TURKEY JOINT STOCK COMPANY.
Manisa OSB 4.Kisim Kecilikoyosb Mah.
Ahmet Nazif Zorlu Bulvari No:19 Yunusemre - Manisa.

hereby declares under its sole responsibility that the air conditioners and heat pumps described below for use in residential, commercial and light-industrial environments:

MITSUBISHI ELECTRIC, MSZ-AP25VGK/MUZ-AP25VG, MSZ-AP25VGK/MUZ-AP25VGH
MSZ-AP35VGK/MUZ-AP35VG, MSZ-AP35VGK/MUZ-AP35VGH
MSZ-AP42VGK/MUZ-AP42VG, MSZ-AP42VGK/MUZ-AP42VGH
MSZ-AP50VGK/MUZ-AP50VG, MSZ-AP50VGK/MUZ-AP50VGH

Note: Its serial number is on the nameplate of the product.

Directives

• 2014/53/EU: Radio Equipment Directive
• 2006/42/EC: Machinery Directive
• 2011/65/EU, (EU) 2015/863 and (EU) 2017/2102: RoHS Directive

Issued: TURKEY 1 November, 2017 Selin Dömekeli Quality Assurance Department

MITSUBISHI ELECTRIC CORPORATION
HEAD OFFICE: TOKYO BUILDING, 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN