LISEN W605 Wireless Car Charger Mount User Manual

This document provides instructions for the LISEN W605 Wireless Car Charger Mount.

Accessory List

Before use, connect the device to power.

Included Accessories:

1) Primary Unit: A wireless car charger mount with adjustable arms and a base.
2) Air-vent Clamp: A clamp designed to attach the mount to car air vents.
3) USB-A to C Cable: A cable for connecting the mount to a power source.

Product Overview

The LISEN W605 features:

Wireless Charging Area: The central part where a Qi-compatible phone is placed for wireless charging.
Clamp Arm: Adjustable arms that grip the phone.
Base Tray: Supports the bottom of the phone.
Clamp Arm Release Button: Used to open the clamp arms.
Wireless Charging & LED Switch: Controls the wireless charging function and LED indicator.

Product Parameters:

TYPE-C INPUT: 5V=2A; 9V=2A; 12V=2A
WIRELESS OUTPUT: 5.0W / 7.5W / 10.0W / 15.0W
INPUT PORT: TYPE-C
MODEL NAME: 2E444

Assembly and Installation

How to Assemble

Step 1: Rotate the nut counterclockwise to detach it from the clamp arm.
Step 2: Insert the ball head through the phone clamp nut socket.
Step 3: Turn the nut clockwise to secure the base ball.

How to Install

Before Installation: Always verify vent compatibility using the schematic diagram to prevent safety hazards.

Compatibility Check: The mount is compatible with horizontal air vents (✔️), but not circular vents (❌).

Step 4: Insert the clamp hook into the vehicle air vent, aligning the clamp arms with the vent louvers.
Step 5: Rotate the clamp knob clockwise to lock onto the vent louvers.
Step 6: Counter-rotate the clamp knob to disengage the clamp hook, then lift vertically to remove the mount.

About Charging

Step 1: Swipe up on the wireless charging and LED indicator switch to ensure it is turned on before starting wireless charging. (Note: The wireless charging switch is usually in the on position by default.)
Step 2: Ensure the mount is connected to a power source before wireless charging.
Step 3: For optimal charging speed, it is recommended to use a power adapter that supports QC 3.0 and PD 18W or higher. Avoid using the USB-A port in the car.

Charging Anomaly Prevention

NOTE:

The product activates LED flicker alerts upon metal foreign object detection.
It is recommended to remove the phone case (non-Magsafe) for better wireless charging.

Items that may interfere with charging:

Metal Pieces ❌
Finger Ring Buckle ❌
Cards ❌
CASE thickness ≥ 2.5mm ❌
Invisible Stand Case ❌

How to Use

Step 1: Press the clip arm switch on the back of the phone clip; the clamp arm will open automatically.
Step 2: Place the phone on the bottom tray, then press the clamp arms (marked areas) until it is secured. Note: Apply pressure only on the textured area to ensure the phone is locked securely. (Full Lock: Must Press Here)
Step 3: Press the release button again to automatically release the clamp arms and remove the phone.

Important Notes

Only phones with Qi wireless charging can use this unit.
Ensure the stand is connected to power before charging your devices.
For optimal charging speed, it is recommended to use a power adapter that supports QC 3.0 and PD 18W or higher.
It is recommended to remove the phone case for wireless charging.
Do not store the product in high temperatures or direct sunlight.
Do not clean with harmful chemicals or detergents.

Regulatory Information

ISED Canada Statement

IC Warning statement: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s).

Operation is subject to the following two conditions:

(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

IC RF exposure statement: This equipment complies with IC Radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 10cm between the product and your body.

FCC Warning

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules.