WHALL ZM1523 Masticating Slow Juicer

Chapter 1: Safety Precautions in Use

1. The input voltage of the appliance is 120V/60Hz. Please confirm it before using the appliance.
2. Disconnect the power supply before dismantling, assembling, or adjusting any part of the appliance.
3. The appliance has a Y connection. If its power cord is damaged, please contact our customer service department for replacement to avoid danger. Do not dismantle and repair it by yourself.
4. Before use, please check if the power cord, the plug, the juice strainer, the spiral pusher, and any other parts are damaged. If any of the said part is damaged, stop using the appliance and contact our customer service department promptly. Do not dismantle and repair it by yourself, otherwise danger may happen.
5. If it is necessary to repair the appliance during use, please contact our customer service department. Do not dismantle it by yourself, otherwise dangers may happen.
6. It is necessary, before connecting the power supply, to ensure that the juicing body, the spiral pusher, the juicing body cap, and all other dis-mountable parts are properly installed.
7. Never put hands or sharp objects into the feed port or contact the spiral pusher when the appliance is running, otherwise injuries may be caused or the appliance may be damaged; never replace the spiral pusher with any other objects or have eyes get close to the feed port, otherwise accidents may happen.
8. Cut food ingredients into small blocks with sizes fitting the feed port of the juicing body. Do not begin to process any vegetables or fruits with cores, hard seeds, or thick skin or shells until they are removed.
9. When feeding a food ingredient, do not make the pushing force too large but have it just enough to cut the food ingredient.
10. Dyeing of the juice strainer, the juicing body cap, the spiral pusher, and other accessories after juicing some vegetables or fruits is normal and will neither affect food eating nor do harm to health.
11. Do not dismantle the dis-mountable parts of the appliance immediately after use, but after both the motor and the spiral pusher have stopped and the power supply is disconnected.
12. Do not sterilize any accessories of the appliance with hot water that is higher than 80°C or a microwave oven, otherwise they may be heated, deformed, and damaged. The materials of all parts in contact with food ingredients should comply with food hygiene certification and be clean, hygienic, and reliable.
13. Do not put the main body into water or another liquid or flush it with water or another liquid, otherwise it may be damaged.
14. Do not clean the appliance with steel wool, abrasive cleaning agents, or corrosive liquids (such as gasoline or acetone).
15. The appliance is applicable to use by individuals or families only.
16. The appliance is not to be used by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.
17. Accessories, other than those supplied with the appliance, include instructions for their safe use.
18. Use a wet cloth to clean surfaces in contact with food before unplugging the plug.
19. Switch off the appliance and disconnect from supply before changing accessories or approaching parts that move in use.
20. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.
21. Warning: Potential danger may arise from misuse.
22. Always disconnect the appliance from the supply if it is left unattended and before assembling, disassembling, or cleaning.
23. To enhance product durability and safeguard its functionality, an intelligent protection chip is integrated into the device. This chip ensures that after 20 minutes of uninterrupted operation, the device will automatically stop. For optimal protection and extended lifespan, we kindly advise waiting for 20 minutes before resuming its usage.

Chapter 2: Parts and Functions

The masticating slow juicer incorporates IMD touch buttons on its control screen. The control screen offers various functions, including Soft Speed, Hard Speed, Power, and Reverse. Here's a detailed description of each function:

Chapter 3: Directions for Use

Before using the appliance for the first time, clean its parts in contact with food ingredients thoroughly (please refer to "Chapter 4: Maintenance").

1. Power Button Status:

After turning on the power, the power button will display a flashing red light. Pressing the power button once will put the juicer in standby. In standby, all four buttons on the control screen will emit white light, with the Soft, Hard, and Reverse buttons flashing. At this time, you can select any function button to start juicing.

2. Working Process:

During the juicing process, the power button and the selected function button will remain illuminated. To stop the juicer, press either the power button or the corresponding function button.

3. Power Failure:

If the juicer remains powered on (with the power button flashing red) without any action for more than three minutes, the screen will turn off, indicating a complete power failure. To resume juicing, simply press any button to enter standby. In standby, all four buttons will emit white light, with the Soft, Hard, and Reverse buttons flashing.

I. Use of the appliance

Please install and use the appliance following the steps below.

Assembly Steps:

1. Connect the juicing body and the main body:

   1. Have the triangular aligning sign "▼" on the juicing body aligned with the aligning "unlocking triangular sign" on the main body and then put the juicing body into the main body (the three clips on the juicing body will realize alignment).

   2. Then turn the juicing body anticlockwise. When there is a click, it suggests that the connection is finished.

2. Install the tray:

   Install the tray on the upper end of the feed port of the juicing body. The tray can make feeding of food ingredients more conveniently, particularly when small-particle food ingredients are processed.

3. Insert the spiral pusher:

   Have the hexagonal shaft of the spiral pusher aligned with the hole on the main body and push it horizontally until it reaches the bottom (when alignment fails, just turn the spiral pusher slightly).

4. Fit the juice strainer:

   Fit the larger-hole end of the juicer strainer into the tail of the spiral pusher and push it while the three clips of the juicer strainer align with the three clamping slots in the juicing body. (The juice strainer is used with the juicing button in the rear only. This function is used for juicing.)

5. Align and insert the end cup:

   Align the triangle alignment mark on the juice extractor with the unlock triangle mark on the juice extractor, and then put the end cup into the juice extractor.

6. Add food ingredients:

   Put food ingredients into the feed port on the juicing body cap to squeeze the fed food ingredients gently for their full contact with the spiral pusher and higher juice extraction efficiency.

7. Place the juice cup:

   Put the juice cup in the corresponding place and have its opening aligned with the bottom of the juice outlet of the juicing body.

8. Place the pulp cup:

   Put the pulp cup below the pulp outlet of the juicing body and have it close to the juice cup.

Chapter 4: Maintenance

1. Before cleaning the appliance, switch off the switch and disconnect the power supply.

2. After use, clean the appliance promptly.

3. Do not wash the main body with water but wipe the stains on it with a piece of wrung rag or cotton cloth.

4. Before storing the appliance, make sure it is clean and dry.

5. Clean the appliance after dismantling it following the steps below.

Disassembly and Cleaning Steps:

1. Rinse cups:

   After the operation is completed, please remove the juice cup and pulp cup in order and rinse them directly with water.

2. Rinse end cup:

   Disassemble the end cup and rinse it with water directly.

3. Rinse filter:

   Remove the filter and rinse it with water. For any food residue, you can use a brush for cleaning.

4. Rinse auger:

   Remove the auger and rinse it with water directly.

5. Rinse pusher:

   Remove the pusher and rinse it with water directly.

6. Rinse tray:

   Remove the tray and rinse it with water directly.

7. Disassemble juicing body:

   To disassemble the juicing body, press and hold the button to unlock it, and then rotate the juicing body in the opposite direction to disassemble it.

8. Rinse juicing body:

   Remove the juicing body and rinse it with water directly.

9. Rinse other parts:

   After removing the juicing body, remove the juicing button, juicing body cap, juice strainer (or squeezer), and other detachable parts. These parts can be flushed with clean water.

Chapter 5: Safety Indexes

Notes:

The information provided covers the analysis and elimination methods for ordinary faults. For other faults, please contact our customer service department. Do not dismantle and repair it by yourself.

[Recycling symbol]