for BAOFENG models including: UV-5R Pro, BAOFENG,BAOFENG,BaoFeng,UV-5R,Pro,8W,High,Power,Radio,144-148Mhz/420-450Mhz,Ham,Radio,Handheld,Two,Way,Radio,with,TIDRADIO-771,Antenna,Walkie,Talkie,for,Off-Roading,5,Pack,Full,Kit,5P(771,Antenna),B0FCY4G68J,B0DJQZJRQL,B0D2HHT9VX,B0DJR17LPJ,B0DMN4WQPH,B07SCZCCPN
BaoFeng UV-5R Pro 5 Pack High Power Radio 144-148Mhz/420-450Mhz Ham Radio Handheld Two Way Radio with TIDRADIO-771 Antenna Walkie Talkie for Off-Roading : Electronics
UV-5R Pro User Guide (PDF) BAOFENG BAOFENG BaoFeng,UV-5R,Pro,8W,High,Power,Radio,144-148Mhz/420-450Mhz,Ham,Radio,Handheld,Two,Way,Radio,with,TIDRADIO-771,Antenna,Walkie,Talkie,for,Off-Roading,5,Pack,Full,Kit,5P(771,Antenna),B0FCY4G68J,B0DJQZJRQL,B0D2HHT9VX,B0DJR17LPJ,B0DMN4WQPH,B07SCZCCPN
BaoFeng BF-F8TD Programming Guide INTRODUCTION BaoFeng BF-F8TD is a dual-band (VHF, UHF) versatile amateur radio. It offers 128 channels, you can add or remove channels from scanning list and give channels alphanumeric names via programming with a computer. With the enhanced capabilities of the F8TD radio, this Programming Guide will help you get a quick start to program the radio. *If you have any problem with the BF-F8TD radio using or programming, please don't hesitate to contact us via support: walkietalkiesoftware.com. Also visit our Facebook pages (TIDRADIO) for more help.It's always our honor to help. Contents 1. Preparation before Programming.......................................................................2 2. Manufacture Software Programming Process ................................................4 3. Chirp Software Programming Process...............................................................11 1 Preparation before Programming 1. Computer System Requirements Manufacture Programming Software Operating System: Windows 7, Windows 8 and Windows 10 CHIRP Programming Software Operating System: Windows 7\8\10, Windows 2000, Mac OS, Linux 2. Programming Cable(This package doesn't include program cable, and you need to order separately) A.USB programming cable - The driver should be installed before programming. 1) Find the corresponding driver of the system. 2) Click install and wait for the installation succeed B.If you use an FTDI cable, it does not need to be installed with a driver. You can just plug in and use directly. 1) If your computer did not automatically install the driver, you will need to update the driver to the latest driver Download the latest FTDI driver at :https://ftdichip.com/drivers/vcp-drivers/ 3. Software Download & Install 1) Turn on the computer, check if your computer system meets the requirements. 2) Download the manufacture software on walkietalkiesoftware.com or CHIRP software on https://chirp.danplanet.com/ 3) Install the programming software 2 4. Connect your Walkie Talkie with Computer 1) Programming cable connects with the computer end. 2) Connect the other end of the cable with your walkie talkie. 3) When both ends have been connected, turn on your radio. Make sure it has enough power during the programming procedure. ERROR: Failed to Connect to the transceiver (Radio) If it says it cannot connect to the radio - this means the cable is working but is not installed correctly into the radio. Items to Check: Radio is turned on The cable is FULLY inserted (it can be deceiving but there is a double click) Hold the cable into the radio - some radios might not make contact without pressure A way to cheat - dampen the pins of the cable before pushing it into the radio. This will give a solid contact 5.How to choose your port? 1.Get into "Window Setting", then search "Device Manager". 3 2.Open "Device Manager", and unfold Port (COM & LPT) to check the existing port. F8TD Manufacture Software Programming Process 1) Download and open the manufacture software. Click "Setting(S)Port" and then Confirm the port the same as the port viewed by Device Manager, then click the "OK" button. 4 2) Click the "Read" button, then click "Start" and ready to read the data from your radio.( Make sure the radio is turned on) 3) You will come to the parameter page and adjust the limited parameters (Channel, Band, RX Frequency, TX Frequency, CTCSS/DCS, Power, and Wide/Narrow, PTT-ID, etc). Channel Information The F8TD radio has 128 channels, you can edit the channel number and channel information according to your needs. The following is an introduction to each term. 5 Name RX Freq TX Freq RX QT/DQT TX QT/DQT POWER W/N PTT-ID Busy Scan add Signal Meaning Receiving frequency Transmitting frequency Receiving CTCSS/DCS Transmitting CTCSS/DCS Transmit power Channel bandwidth When to send the PTT-ID Busy Channel Lockout Signal code Setting Description VHF:136-174MHz UHF:400-520MHz VHF:136-174MHz UHF:400-520MHz Refer to the DCS table and Mutes the speaker of the CTCSS table in the manual. transceiver in the absence of a specific low level digital signal. If the station you are listening to does not transmit this specific signal,you will not hear anything. Refer to the DCS table and Transmits a specific low-level CTCSS table in the manual. digital signal to unlock the squelch of a distant receiver (usually a repeater). HIGH/LOW High power:8W Low power:1W WIDE/NARROW Wideband (25kHz bandwidth) narrowband (12.5 kHz bandwidth). OFF does not send Codes are sent during either the code; beginning or end of a transmission. BOT press PTT button to send code; EOT release PTT button to send code; BOTH press and release PTT button to send code OFF/ON ON: If the channel is occupied, when you press the [PTT] key on this channel, the radio will make a beep tone and will not transmit any signal. OFF: No matter if the channel is occupied, the radio will transmit the signal when you press the [PTT] key. OFF/ON In the scan mode, whether add the channel to the scan list. ON: the channel is added to scan list; OFF: the channel cannot be scanned. 1-15 Selects 1 of 15 DTMF codes. The DTMF codes are programmed with 6 Name Customize channel name Up to 10 digits. software and are up to 5 digits each Support alphanumeric channel name. 4) Click "Optional Features" under "Edit", a page of "Optional Features" will pop up, you can adjust the limited parameters (VOX Function, Squelch, Backlit, DTMF, FM Radio, Voice Prompt, Scanning, VFO Mode, etc.). A.Basic Setting Name TOT(Time Out) Meaning Transmission time-out timer Squelch Level Settings 15-600(s) 0-9 Description This feature provides a limits transmission time to a programmed value. This will promote battery conservation by not allowing you to make excessively long-time transmissions and in the event of a stuck PTT switch, it can prevent interference to other users as well as battery depletion. Mutes the speaker of the transceiver in the absence of a strong signal. Squelch is either OFF or 1-9 levels. The higher level, the stronger the signal must be to in-mute the 7 VOX Voice Annunciation ABR Work mode Voice operated 0-10 TX Display time OFF\English\Chin ese OFF/0-5 (s) Frequency Channel speaker. When enabled it is not necessary to push the [PTT] button on the transceiver. Adjust the gain level to an appropriate sensitivity to allow smooth transmission. Switch the language of menu display and voice prompts Time-out for the LCD backlight. CHs is channel quantity B.Channel Mode You can customize the display on Channel A/B: CH: Display Channel Number CH + Name: Display Channel Number and Channel Name (Name column in Channel information part) CH + Freq: Display Channel Number and Frequency C.DTMF Name Setting Description DTMF ST OFF ALL: No DTMF Side Tones are Determines when DTMF side tones (DTMF side tone of heard can be heard from the transceiver transmit code) KB DTMF Side Tone: Side Tones are speaker heard only from manually keyed DTMF codes Send ANI DTMF Side Tone: Side Tones are heard only from automatically keyed DTMF 8 Save mode Scan mode PTT_ID PTT Delay KB_LOCK AutoLock (automatic keypad lock) BCL (busy channel Lock-out) Beep (keypad beep) codes KB DTMFST+Send ANI DTMFST: All DTMF Side Tones are heard OFF/1:1/1:2/1:3/1:4 Selects the ratio of sleep cycles to awake cycles. The higher number the longer the battery lasts. When enabled, a word or two might be missed when the frequency being monitored becomes active. TO: Time Operation - scanning will Scanning Resume Method resume after a fixed time has passed CO: Carrier Operation -Scanning Resume Method scanning will resume after the signal disappears SE: Search Operation scanning will not resume OFF: No ID is sent When to Send PTT-ID; Codes are BOT : The selected S-CODE is sent at sent during either the beginning or the beginning end of a transmission. EOT: The selected S-CODE is sent at the ending BOTH: The selected SCODE is sent at the beginning and ending 0-30ms Signal code sending delay If you select this option, the keyboard is locked. When ON, the keypad will be locked if not used in 8 seconds. Pressing the [#O] key for 2 seconds will unlock the keypad. Check: If the channel is occupied, when you press the [PTT] key on this channel, the radio will make a beep tone and will not transmit any signal. Uncheck: No matter if the channel is occupied, the radio will transmit the signal when you press the [PTT] key. Allows audible confirmation of a key press 9 D.Frequency mode STEP: Select the amount of frequency change in VFO/Frequency mode when scanning or pressing the keys. SFT_D: Enable access of repeaters in VFO/Frequency Mode ([OFF]: TX = RX (simplex); [+]: TX will be shifted higher than RX in frequency; [-]: TX will be shifted lower than RX in frequency) Offset: Specifies the difference between the TX and RX frequency (For the explanation of TX Power, RX QT/DQT, TX QT/DQT, W/N, Signal, please refer to introduction above) E.FM Radio FM Radio Enable: When you check off, FM Radio function will be activated on the radio. Roger: Sends an end-of-transmission tone to indicate to other stations that the transmission has ended TX Under TDR Start: Transmit selection while in Dual Watch mode, when enabled, priority is returned to selected display once the signal in the other display disappears. TDR: Dual Watch mode, the ability to monitor two channels at once can be a valuable asse 10 5) Finally, all the modification will be saved by clicking the "Write" button, then clicking the "Start" button on the popup. And you can check the setting you modified after reboot the radio. F8TD Chirp Software Programming Process 1) Open the CHIRP software (Latest Version), click "Download From Radio" under "Radio" 11 2) Select the corresponding cable driver port, and select Model "TD-UV5R TriPower" under Vendor "TIDRADIO", then click "OK" to read the radio 3) And you will come to the page of Memories, in which you can adjust the limited parameters (For the explanation of Channel, TX Frequency, RX Frequency, CTCSS/DCS, High/Low Power,and Wide/Narrow,Band.Please refer to introduction above) 4)Then if you switch to the page of Settings, you can adjust the limited parameters(For the explanation of VOX Function, Squelch, Backlit, DTMF, FM Radio, Voice Prompt, Scanning, VFO Mode.Please refer to introduction above) 12 5) All the modification will be saved by clicking "Upload To Radio" under "Radio". Then you can check the settings you modified after reboot the radio. *If you have any problem with the BaoFeng F8TD radio using or programming, please don't hesitate to contact us via support: walkietalkiesoftware.com.Also visit our Facebook pages (TIDRADIO) for more help. It's always our honor to help. 13WPS 文字