Amazon.com
User Guide for CP PLUS models including: CT21 Wi-Fi Bullet Camera, CT21, Wi-Fi Bullet Camera, Bullet Camera, Camera
prieš 22 valandas — Quick Start Guide. CT21. Camera ×1. LED Indicator. Lens. Reset Button. Wi-Fi Antenna. Micro SD Card Slot. Built-in Mic. Spotlight. LED Status.
QSG ×1 . . Version 1 0 0. Quick Start Guide. CT21. Camera ×1. LED Indicator. Lens. Reset Button. Wi-Fi Antenna. Micro SD Card Slot. Built-in Mic. Spotlight.
File Info : application/pdf, 2 Pages, 2.80MB
DocumentDocumentPackage Content Camera Introduction Operating with eezo APP Quick Start Guide CT21 Version 1.0.0 Camera ×1 Positioning Map ×1 Power Adapter ×1 Screw Package ×1 LED Indicator Lens Built-in Mic Reset Button Spotlight Wi-Fi Antenna The pattern of the LED indicator is included in the following table. LED Status Red light on Green light flashing Green light on Red light flashing Green and red light flashing alternately Device Status Powered off/LED turned off Reboong aer reset Boong Device malfuncon Waing for network Operang properly Network connecon failed Firmware updang Micro SD Card Slot Voice control works with Alexa or Google Assistant - You can control your camera using just your voice with Alexa or Google Assistant-enabled devices. QSG ×1 Waterproof Connector ×1 Google, Google Play and Google Home are trademarks of Google LLC. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. Step 1 Scan the following QR code or search "eezo" in Google Play or App Store to download and install the app. Note: If you have installed the app, update it to the latest version. Step 2 Run eezo App, and then register an account for the first use. Step 3 Connect the camera to power source with the power adapter. About the Guide shall prevail if there is any inconsistency. Step 4 Wait for booting to be finished, and then the camera indicator flashes with green light. - Please visit our website or contact customer service if there is any problem when using the device. - If there is any uncertainty or controversy, we reserve the right of final Step 5 Do the following operations to finish adding camera. Select Wi-Fi Wi-Fi XXXXXX1 Wi-Fi XXXXXX2 Wi-Fi XXXXXX3 Wi-Fi Password ... Thank you for choosing eezo Note: If you have more than one camera, do step 5 to add them one by one. If the Wi-Fi network has changed or the indicator status goes wrong, reset the camera, and then do step 5 to add it again. Installing Camera Note: Make sure that the mounting surface is strong enough to hold at least three times of the device weight. Camera Self-tapping Screw Expansion Bolt Mounting Surface Positioning Map Step1 Drill screw holes on the mounting surface as the positioning map shows, and then put in the expansion bolts. Step2 Attach the pedestal to the mounting surface with the self-tapping screws. Step3 Power up the camera, and then adjust the lens to the ideal angle. FAQ Q: The device cannot boot up or work as expected? Check the LED indicator status. If the light is not in green, press and Q: How to connect the camera to another Wi-Fi network? If the camera is online, select camera> sengs>Device Seng> WLAN>Network Config to change the Wi-Fi connecon on the app. If the camera is offline, reset the camera, and then configure the camera again. Check if the distance between the camera and the router, and that between the camera and the smart phone is both within 5 m (16.4 auto, and the mode to 11bgn mixed. Q: When the micro SD card is full, how is the recorded video saved? When the micro SD card is full, the system will overwrite the previous Troubleshooting Problem Cannot configure the camera Soluon · Make sure that your smart phone and the camera are within · range of your Wi-Fi router. Make sure that the LED indicator on the camera is flashing green . How to find the camera It is the safety code on the device label. Wi-Fi password No picture or device is offline Picture is not clear · Make sure that the LED indicator on the camera is flashing green. See "LED Status" secon for details if otherwise. · Make sure that the camera is properly connected to power using the included USB power adapter. · Reposion the camera, router, or both to improve signal strength. · Check the camera lens for dirt, dust, and spider webs. Clean the lens with a so, clean cloth. · Remove the vinyl cover on the camera lens. No audio · Make sure that audio funcon on camera is turned on. · Make sure that audio is turned up on viewing device. Human detecon does not work Make sure that you have enabled Human Detecon in the Device Sengs interface of eezo App. Camera stuck downwards Check Privacy Mode seng on eezo App. Fail to scan QR code · Clean the camera lens of your smart phone. · Make sure that there is enough light on the QR code. · Do not hold the QR code too close to the camera.