SONANCE GARDEN SERIES SGS SYSTEM
INSTRUCTION MANUAL
Introduction
Thank you for purchasing the SONANCE GARDEN SERIES SGS SYSTEM. When properly installed, this system will provide you with years of outdoor entertainment pleasure. To get the most out of your new system, please read this manual thoroughly before you begin installation.
Box Contents
SONANCE SGS SYSTEM box contains:
- (8) Satellite speakers with vertical pivoting knuckle
- (8) Removeable speaker stakes with 1/2" NPS threading
- (1) In-Ground subwoofer
Speaker Layout Planning
The SONANCE SGS SYSTEM is designed to deliver a seamless, evenly dispersed sound field in an 'open air' environment. A daisy chain of multiple satellite speakers and a subwoofer should be strategically placed to create even, balanced coverage, minimizing 'hot spots' and 'cold spots' around the outdoor entertainment area.
The satellite speakers should be placed from 8 to 10 feet (2.4 - 3 meters) apart for best coverage. To achieve the best balance between the satellites and subwoofer, the subwoofer should be placed as close to the center of the satellites as possible.
If more bass is required, placing the subwoofer near a wall or other solid structure will greatly reinforce the low bass frequencies. In some cases, you may want to place the subwoofer closer to your primary listening position or add a second Sonance Garden Series subwoofer.
The satellites in the SONANCE SGS SYSTEM individually present a 30 ohm load to the amplifier. When 4 of them are connected on each amplifier channel in parallel, the load to the amplifier is approximately 7.5 ohms. The satellites and subwoofer both feature internal crossovers so the subwoofer's impedance is not combined with the satellites. The overall load presented to your amplifier by the SONANCE SGS SYSTEM will be around 7.5 ohms nominal.
Satellite Speaker Description: SGS SAT Satellite Speaker
Subwoofer Description: SGS SUB In-Ground Subwoofer
Diagram Description (Figure 1: Wiring Diagram): Illustrates a typical outdoor audio setup with an amplifier connected to multiple satellite speakers and an in-ground subwoofer in a daisy-chain configuration, showing left and right channel wiring.
Diagram Description (Figure 2): Depicts the required burial space for the subwoofer, showing a 14-inch diameter and 15-inch depth, with approximately 5 inches of the enclosure exposed above ground.
Types of Wire
Color-coded, 14/4 direct-burial speaker wire is recommended.
Wire Gauge Chart:
| Wire Gauge | Distance |
|---|---|
| 18 Gauge | Up to 100 feet (30 meters) |
| 16 Gauge | Up to 150 feet (45 meters) |
| 14 Gauge | Up to 250 feet (80 meters) |
Best Practice: '14/4' refers to 14 gauge, 4-conductor wire. It is important to use only 'direct burial' wire to maintain long-term signal integrity and prevent corrosion. Using individual conductors with different colors makes it easy to identify and access both amplifier channels. Low voltage lighting wire can also be used but is only sold as a 2-conductor wire. If using a 2-conductor wire, run two pairs of wires; one for each amplifier channel (Right/Left).
Subwoofer Burial Note: The subwoofer requires a burial space that is about 14" diameter and 15" deep. When the subwoofer is in the ground, ensure that there is roughly 5" of exposed subwoofer enclosure from the surface of the ground to the bottom edge of the canopy.
Speaker Installation
- Place the 8 satellites and 1 subwoofer in their approximate final locations.
- Dig a 4" to 5" trench to run the speaker wires in. Be sure to check local codes for trenching limitations.
- Starting at the amp location or wire connection point, run the speaker wire through the trench to the first speaker location.
- Once the speakers and subwoofer are laid out in their locations and the wiring is completed per this installation guide, stake or mount the speakers into their final locations and bury the subwoofer in its final location.
Connecting the Speakers (using 14/4 direct burial speaker wire)
- Pull the 14/4 wire on the spool to the furthest speaker location. Leave the wire attached to the spool until the last speaker has been connected.
- Starting at the first speaker and every speaker that follows, create a loop of wire approximately 6" in length.
- Use a round cable stripper to remove the outside protective wire jacket to expose the 4 individual color-coded wires. For guidance, search for videos on 'Using a Round Cable Stripper' or visit the manufacturer's website.
- Use a wire tie to keep the wire loop intact and act as a strain relief.
- Wire Color Coding: For the Right Channel, use the RED (+) and BLACK (-). For the Left Channel, use the WHITE (+) and GREEN (-).
- Cutting Wires Example: To connect the first speaker to the right channel, cut the red (+) and black (-) wires only. Leave the white and green wires intact.
- Strip off 3/4 inch of insulation on the red and black wires to expose the copper conductor. Combine and twist the red wires from the amplifier, the first satellite, and the wire running to the next speaker in a clockwise motion.
- Secure these three wires using the provided silicone-filled wire nuts, ensuring that NO COPPER is exposed.
- Wrap the wire nut and surrounding wire connection in electrical tape to protect from moisture.
- At the next speaker, repeat steps 2–7 for the left channel using the white (+) and green (-) wires, leaving the red (+) and black (-) wires intact.
- Continue these steps for the remaining 6 speakers in the daisy-chain.
Important Note: Be sure only 4 satellite speakers are connected to each amp channel. Mis-wiring may result in an unacceptable load which could damage your amplifier.
Connecting the Speakers (Using a 2-Conductor Wire or Low Voltage Lighting Wire)
- Pull the first pair of 2-conductor wire to the furthest speaker location, leaving it connected to the spool near the amplifier.
- Starting at the furthest speaker and every other speaker that follows, create a loop of wire approximately 6" in length, securing the loop with a wire tie.
- Cut the wire at the last speaker location in the daisy-chain closest to the amplifier.
- Take the spool back to the starting point and pull a second 2-conductor wire to the furthest speaker location and repeat steps 1 and 2.
- Starting with the first speaker, cut the wire loop.
- Polarity Note: If not using color-coded wire, one wire in the pair will have a different texture or printing. Use this as the (+) terminal and the other as the (-) terminal. Maintain this polarity standard for all connections.
- Strip the insulation on each wire to expose approximately 3/4" of copper. Combine and twist all the positive (+) wires together in a clockwise motion. Repeat this step for all the negative (-) wires.
- Secure the three wires together using the provided silicone-filled wire nuts, ensuring that NO COPPER is exposed.
- Repeat steps 5–7 for the remainder of the speakers.
Diagram Description (Figure 4): Illustrates the daisy-chain wiring for multiple speakers using 2-conductor wire, showing left and right channel connections.
Subwoofer Wire Connection
The subwoofer features a dual voice coil driver with 4 wires, one pair for each of the amplifier channels: RED (+) and BLACK (-) for the right channel, WHITE (+) and GREEN (-) for the Left channel. The subwoofer can be connected at any point along the daisy chain (beginning, middle, or end). Locating the subwoofer mid-way in the daisy chain will produce an equal amount of bass for the speakers on either side of the sub. The subwoofer needs to be connected in the same manner as the satellite speakers.
Important Note: The subwoofer has dual voice coils, one for the left channel and one for the right channel. It is critical that the positive and negative wires be connected correctly for both channels. If either channel is connected incorrectly, no low-frequency sound will be produced.
Diagram Description (Figure 5): Shows the wiring connection for the subwoofer from the amplifier to the next speaker.
Diagram Description (Figure 6): Illustrates the wiring connection for the subwoofer from the amplifier to the next speaker, detailing the dual voice coil connections.
Final Connection and Testing
After all satellite and subwoofer connections are completed, connect the wires to your receiver or amplifier.
Important Safety Note: Be sure not to let any stray '+' and '-' strands touch each other. Touching strands will cause a short-circuit which could damage your amplifier.
Turn your source and amplifier/receiver on and test the system with your favorite music. If the speakers are operating properly, refill the wire trench and enjoy your new Sonance Garden Series System.
Specifications
SGS Satellite Speaker
- Tweeter: 3/4" (19mm) Polyurethane dome
- Woofer: 3.5" (89mm) Anodized aluminum cone & Santoprene™ surround
- Frequency Response: 80Hz - 20kHz +/-3dB
- Impedance: 30 Ohms nominal
- Power Handling: 50 watts minimum; 200 watts maximum
- Sensitivity: 87dB 2.83V / 1 meter
- Enclosure Material: Non-corrosive, high-heat ABS sealed enclosure
- Mounting Threads: 1/2" NPS (National Pipe Standard)
- Dimensions (L x Dia.): 6.5" L x 4.5" Dia. (165mm x 114.8mm)
- Shipping Weight: 5.0lbs (2.4kg) each
SGS Subwoofer
- Woofer: 10" (254mm) dual voice coil, polypropylene & Santoprene surround
- Frequency Response: 35Hz - 100Hz ±3dB
- Crossover Frequency: 100Hz
- Power Handling: 200 Watts
- Sensitivity: 90dB Sensitivity @ 2.83V / 1 meter
- Enclosure Material: High Density Polyethylene (HDPE) non-corrosive sealed enclosure
- Dimensions (LxDia.): 24.8" x 15" (630mm x 381mm)
- Shipping Weight: 40 lbs (19kg)
Speaker Wire Recommendations:
- 18 gauge - up to 100 ft. (30m)
- 16 gauge - up to 150 ft. (45m)
- 14 gauge - up to 280 ft. (85m)
CAD files available for download at www.sonance.com
Limited Three (3) Year Warranty
Sonance warrants to the first end-user purchaser that this Sonance-brand product (product), when purchased from an authorized Sonance Dealer/Distributor, will be free from defective workmanship and materials for the period stated above. Sonance will at its option and expense during the warranty period, either repair the defect or replace the Product with a new or remanufactured Product or a reasonable equivalent.
Exclusions
To the extent permitted by law, the warranty set forth above is in lieu of, and exclusive of, all other warranties, express or implied, and is the sole and exclusive warranty provided by Sonance. All other express and implied warranties, including the implied warranties of MERCHANTABILITY, IMPLIED WARRANTY OF FITNESS FOR USE, AND IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED.
No one is authorized to make or modify any warranties on behalf of Sonance. The warranty stated above is the sole and exclusive remedy and Sonance's performance shall constitute full and final satisfaction of all obligations, liabilities and claims with respect to the Product.
In any event, Sonance shall not be liable for consequential, incidental, economic, property, bodily injury, or personal injury damages arising from the Product, any breach of this warranty or otherwise.
This warranty statement gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow the exclusion of implied warranties or limitations of remedies, so the above exclusions and limitations may not apply. If your state does not allow disclaimer of implied warranties, the duration of such implied warranties is limited to the period of Sonance's express warranty.
Your Product Model and Description: Sonance Garden Series SGS System
Warranty Period for this Product: Three (3) years from the date on the original sales receipt or invoice or other satisfactory proof of purchase.
Additional Limitations and Exclusions from Warranty Coverage:
The warranty described above is non-transferable, applies only to the initial installation of the Product, does not include installation of any repaired or replaced Product, does not include damage to allied or associated equipment which may result for any reason from use with this Product, and does not include labor or parts caused by accident, disaster, negligence, improper installation, misuse (e.g. overdriving the amplifier or speaker, excessive heat, cold or humidity), or from service or repair which has not been authorized by Sonance.
Obtaining Authorized Service:
To qualify for the warranty, you must contact your authorized Sonance Dealer/Installer or call Sonance Customer Service at (949) 492-7777 within the warranty period, must obtain a return merchandise number (RMA), and must deliver the Product to Sonance shipping prepaid during the warranty period, together with the original sales receipt, or invoice or other satisfactory proof of purchase.
©2019 Sonance. All rights reserved. Sonance is a registered trademark of Dana Innovations. Due to continuous product improvement, all features and specifications are subject to change without notice. For the latest Sonance product specification information visit our website: www.sonance.com
Contact Information:
Sonance, 991 Calle Amanecer, San Clemente, CA 92673 USA
Phone: (949) 492-7777 | FAX: (949) 361-5151 | Technical Support: (949) 492-7777
Website: www.sonance.com
