AUTOMATIC SWING DOOR OPERATOR

Content

1. Introduction of product
2. Technical parameters
3. Swing door operator
4. Components
5. Installation step
   • Installation demonstration
   • Installation of bottom plate
   • Installation of pull bar
   • Installation of pull bar for glass door
   • Installation of push bar
   • Installation of Glass clamp for push bar
   • Mechanism installation
6. Wire diagram
7. Data setting
8. Function of remote
9. LED instructions

Important Safety Information

Warning: ⚠️ Installation of automatic doors should be entrusted to the appointed distributor or professional installation personnel, or it may be dangerous.

• Installation must be performed by professional installation personnel according to local law.
• This manual must be kept well for maintenance.

1. Introduction of product

Application: Suitable for wooden doors, metal doors, frame doors, open to one direction (both single or double open). Special glass clamp is requested for glass door installation.

Adjustable Features: Speed/opening time/open degree/close force adjustable.

Specifications:

• Door width: ≤ 1200mm
• Door weight: ≤ 150kgs
• Open degree: 60-110° adjustable
• Installation: open to inside / open to outside (pull/push bar)
• Voltage: AC100V-240V, Output 24 DC
• Open device: wireless push button/remote control
• Service life: 2,000,000 times, super reliable.

Key Features:

• 55W high-speed DC brushless motor, long service life, low noise.
• Main and slave mode operation. Sequence will not change because of encountering an obstacle.
• Double gear box design, high speed ratio, high strength. Can work with 150kgs doors (work with E-lock for enhanced safety).
• Push and go function.
• The controller voltage is AC100V-240V, applicable worldwide.
• The rated power of the motor is 55W.

Components Diagram:

The system includes:

• 1. Swing door mechanism
• 2. Microwave sensor
• 3. E-lock
• 4. Access control
• 5. Touchless sensor
• 6. Footkick sensor
• 7. Remote control
• 8. Keypad Integration Access Control
• 9. Push button
• 10. Touchless sensor
• 11. Wireless push button
• 12. Top Scan

2. Technical Parameters

• Power: AC 100V-240V
• Active open time: 3-7s/90°
• Hold open time: 0-20s
• Temperature: -20℃ to +55℃
• Protection class: IP21
• Product weight: 5.5kg
• Product size: 475*81*98mm
• Max open angle: 110°

Door Width vs. Door Weight Chart:

A chart illustrates the relationship between door width (cm) and door weight (kg), showing a 'Limited range' and a 'Suitable range'. The suitable range extends from 60cm width and 50kg weight up to 120cm width and 150kg weight, with specific curves indicating limitations.

3. Swing door operator

Design for Barrier-Free Accessibility, convenient for the disabled and children.

Dimensions:

Pull bar: Overall length 500mm, width 98mm, height 81mm. Arm length varies.

Push bar: Overall length 500mm, width 98mm, height 81mm. Arm length varies.

Detailed diagrams show the dimensions for both pull bar and push bar configurations.

4. Components

The main unit consists of:

• Side Cover
• Controller
• Motor
• Side cover (with power switch)
• 100-240V power input
• Pull bar

Included components for installation:

• Base plate
• Pull bar
• Cover
• Push bar
• Door operator unit

Note: Select one from the pull bar or push bar.

5. Installation step

5.1 Installation demonstration

Pull bar type: Suitable for doors opening inwards (mechanism is inside).

Diagrams show the placement of the operator and arm for an inward-opening door.

Push bar type: Suitable for doors opening inwards (mechanism is inside).

Diagrams show the placement of the operator and arm for an inward-opening door with a push bar.

5.2 Installation of bottom plate

For pull bar type:

Diagrams illustrate fixing the bottom plate to the frame with eight countersunk head screws for both right and left operator positions.

For push bar type:

Diagrams illustrate fixing the bottom plate to the frame with eight countersunk head screws for both right and left operator positions. Ensure a 6mm distance between the bottom of the mounting plate and the door hole.

5.3 Installation of pull bar

1. Open the door to 90°, slide the pull guide roller into the track.
2. Fix the Pull bar plate as shown.
3. Move the plate to ensure the wheel is in the middle position of the track.
4. Hold the plate position and fix the first screw near the center of the shaft.
5. Close the door, repeat step 3, and fix another screw at the other side.
6. Manually move the door to ensure the pull bar works smoothly. Adjustment is requested if any resistance occurs during operation.
7. Fix the last screw.

Installation of pull bar guider (Right position): Fix the pull bar on the door leaf with 3 self-tapping screws. Adjust the opening angle using the position stopper.

Installation of pull bar guider (Left position): Fix the pull bar on the door leaf with 3 self-tapping screws. Adjust the opening angle using the position stopper.

5.4 Installation of pull bar for glass door

Diagrams show the installation for glass doors. Tip: Ensure a 25mm space for the glass top to the door frame bottom.

5.5 Installation of push bar

Diagrams show the installation of the push bar. Adjust the push bar length by two screws according to the door frame's depth (L ≤ 250mm).

Installation of push bar for glass door: Automatic door right installation.

5.6 Installation of Glass clamp for push bar

Note: Make sure there is a 10mm gap between the top of the glass and the bottom of the door when using the push arm of the glass door.

Diagrams show the attachment of the glass clamp. Tip: The glass clamp of the push arm shall be fastened on the door wing with 4 plug screws (M6*12). Install the fix plate of the push bar with 2 screws (M5*8) on the glass clamp.

5.7 Mechanism installation

Diagrams illustrate hanging the mechanism on the fixed base cover with screws and assembling/disassembling the mechanism cover.

6. Wire diagram

Detailed wiring diagrams are provided for various components:

• DIP Switch settings: Explains the function of each DIP switch for lock modes, push and go, opening direction, master/slave drive, and signal shielding.
• Inter lock: Wiring for two doors to interlock.
• Synchronous: Wiring for synchronous operation of two doors. Includes a note about controller alarms for incorrect connections and bridging terminals 17 and 19 for single-mode operation.
• 24G Microwave sensor: Wiring connections for the sensor.
• UPS: Wiring for the Uninterruptible Power Supply.
• AK04 Controller: Wiring connections for the controller unit.
• Footkick sensor: Wiring for the footkick sensor.
• Photocell: Wiring for photocell sensors, noting the use of the 'NC' signal.
• Connection of E-lock: Wiring for electric bolt locks and magnetic locks.
• Access keypad: Wiring connections for the access keypad.
• TOP Scan (Open and Close): Wiring diagrams for the TOP Scan sensor in both open and close modes, specifying connections for power, relays, and optical couplers.

7. Data setting

DIP Switch Settings: Detailed explanation of DIP switch functions for various operational modes (e.g., E-LOCK, Push and go, L/R switch, Master/Slave, Signal shielding).

Parameter Adjustments:

• Close buffer distance: Distance increase clockwise.
• Open buffer distance: Distance increase clockwise.
• Open speed: Open speed increase clockwise.
• Close speed: Close speed increase clockwise.
• Buffer speed: Buffer speed increase clockwise.
• Open hold time: Hold time increase clockwise (0-20s adjustable).

Note: DIP switch selections only take effect after a system restart.

Button on the controller:

• Test: Press to activate one open-close cycle.
• Learn: Remote setting button.

LED Indicator:

• L1: Remote setting indicator (Blue).
• L2: Master drive indicator, flashes once every 4 seconds (Red).
• L3: Slave drive indicator, flashes once every 4 seconds (Green).

8. Function of remote

Remote Control Functions (FC04):

• A: Always open
• B: Automatic
• C: Open one time
• D: Full lock

Adding a remote: Press and hold the controller's learning button (L1 Blue LED on), release, then press 'A' on the remote. The remote is added when the Blue LED flashes 3 times.

Deleting a remote: Press and hold the controller's learning button for 9 seconds (L1 turns from blue to flashing). All remotes are deleted. (Attention: Keep the learning button pressed during deletion).

Wireless push button: Adding and deleting wireless push buttons is the same as for remotes. Check DIP switch settings if necessary.

Notes:

1. The built-in receiver supports 'always open', 'automatic', 'open one time', and 'full lock' functions. It also works with wireless push button PB04. PB04 can activate the door even when the controller is in 'full lock' mode.
2. Exit only function: Connect an outside sensor or button to 'Open-B' and an inside sensor or button to 'Open-A'. Then press the 'full lock' button on the remote.
3. Double open mode: Connect the synchronous line as per the manual. Ensure settings are consistent upon power-on. Adjust open/close speed, buffer speed, and hold time if they are not synchronized.
4. When operating in double open mode, the transmitter should learn both operators together.
5. In double open mode, accessories should be connected to both controllers in parallel.

9. LED instructions

Double open

Single open

Troubleshooting

• Overcurrent protection: Buzzer beeps every 1 second, Red and green LEDs flash 5 times together within 4 seconds.
• Motor problem: Buzzer beeps every 2 seconds, Red and green LEDs flash 4 times together within 4 seconds.