User Guide for LobiBox models including: KSIG-WLS-TX6, K-SIG, 6 Channel Wireless Transmitter and Receiver, K-SIG 6 Channel Wireless Transmitter and Receiver

LobiBox K‐SIG 6‐Channel Wireless Transmitter User Guide

LobiBox K‐SIG 6‐Channel Wireless Transmitter (PCB Only) KSIG‐WLS‐TX6

LobiBox K‐SIG 6‐Channel Wireless Receiver User Guide

LobiBox K‐SIG 6‐Channel Wireless Receiver (PCB Only) KSIG‐WLS‐RX6

• Google Docs
• Google Drive
• Download [pdf]
• Download Optimized



File Info : application/pdf, 10 Pages, 1,011.11KB

Document Document

K-SIG BY LOBIBOX
6 CHANNEL WIRELESS TRANSMITTER & RECEIVER
APRIL 26 2022
Introducing the newest line of products by LobiBox. Chris Pryor ­ Technical Specialist
1

Table of Contents
TRANSMITTER ­ 6 CHANNEL WIRELESS................................................................... 3 TRANSMITTER COMPONENTS................................................................................. 4 RECEIVER ­ 6 CHANNEL WIRELESS .......................................................................... 5 RECEIVER COMPONENTS ........................................................................................ 6 ANTENNA COMPONENTS (OPTIONAL) .................................................................... 7 USE CASE 1 ............................................................................................................. 8 USE CASE 2 ............................................................................................................. 9
2

TRANSMITTER ­ 6 CHANNEL WIRELESS
Part #: KSIG-WLS-TX6
1. Addressable Dip Switch: Set Receiver to same address 2. Inputs: Dry contact ONLY 3. Input Power: 12VDC to 24VDC 4. Line of Sight: 300 yards
a. One mile (with extended range antenna) 5. Frequency: 433Mhz ** Do not place in metal containers unless antenna protrudes **
3

TRANSMITTER COMPONENTS
1

2

5

4

6

3
1. Power a. Power IN + b. Power IN ­
2. Antenna a. U.FL connector
3. Output from your device (IN 1 ­ IN 6) a. Motion, Beam, Switch, etc.
4. Input Trigger Test Button 5. Reset Button 6. Addressable Dip Switch

4

RECEIVER ­ 6 CHANNEL WIRELESS
Part #: KSIG-WLS-RX6
1. Addressable Dip Switch: Set Transmitter to same address 2. Outputs: Contact Rating ­ 250VAC 10A/28VDC 10A
a. Form C Relays (Common, Normally Open, Normally Close) 3. Input Power: 12VDC to 24VDC 4. Line of Sight: 300 yards
a. One mile (with extended range antenna) 5. Frequency: 433Mhz ** Do not place in metal containers unless antenna protrudes **
5

RECEIVER COMPONENTS
1
4 5
2
3
1. Power a. Power IN + b. Power IN ­
2. Antenna a. U.FL connector
3. Form C Relays (RLY 1 ­ RLY 6) a. Common (C) b. Normally Close (NC) c. Normally Open (NO)
4. Reset Button 5. Addressable Dip Switch
6

ANTENNA COMPONENTS (OPTIONAL)
3dbi Antenna Kit Part #: KSIG-ANT-3DBI
 (2) U.FL to Female SMA Cable  Cable Length: 14cm  (2) 3dbi Antenna  300-500m line of sight 10dbi Antenna Kit Part #: KSIG-ANT-10DBI
 (2) U.FL to Female SMA Cable  Cable Length: 300cm  (2) 10dbi Antenna  500-900m line of sight
7

USE CASE 1

Control Panel
 Control Panel o Transmitter will send signal to Receiver 1  Use push button to open North Gate.  Use on/off switch for Closed Sign. o Transmitter will send signal to Receiver 2.  Use push button to open Dock Door.

Dock Door

8

USE CASE 2
 Gate (East & West) o Gates connected to camera or intercom system. o Gates connected to Push buttons from Transmitter. o Push buttons (Transmitter) will send signal to Receiver to open gate.
 Doors (NW, SW, NE, SE) o Door Transmitters connected to door contact. o Transmitter will send signal to Indicator Panel connected to Receiver that door is open.
 Docks (East & West) o Dock Transmitters connected to motion sensor. 9

o Motion sensor (Transmitter) will send signal to Indicator Panel connected to Receiver
o Docks connected to Push buttons from Transmitter. o Push buttons (Transmitter) will send signal to Receiver to open door.
10