User Manual for Gazebo models including: Gazebo, Steel Gazebo, MA-OB-HTG006, 3050826
We are forever grateful and appreciative of you considering purchasing our product. After careful evaluation of our product.
Steel Gazebo Assembly Instruction MA-OB-HTG006 We are forever grateful and appreciative of you considering purchasing our product. After careful evaluation of our product serie, we are excited to launch this product to the public as it is more technically advanced with lots of exciting and useful features. One of the great features added to the arsenal is its mere size, which will require 3-4 people with about 4-5 hours of installing time. Making it a beast at its finest! Steel Gazebo Assembly Instructio A 4H 4 B 2 H1 4 B1 2 H2 2 C 2 H3 2 C1 2 J1 4 D 6 J2 4 E 4K 1 F 4 K1 1 F1 4L 4 G 6 M1 10 G1 2 M2 8 G2 2 M3 6 G3 2 M4 4 G4 2 M5 96 G5 2 M6 4 G6 2 M7 2 G7 2 M8 4 G8 2 N1 2 G9 2 N2 2 G10 2 N3 2 N4 2R 72 N5 2 R1 20 N6 2S M6*47 14 N7 2T M6*25 82 N8 2U M6*25 1 O1 2 U1 4 M6*30 O2 2V 132 M6*15 O3 2X M6*10 32 O4 2 X1 M6*42 8 O5 2W 10 M6*50 O6 2Y 5*12 64 P 4 Z1 1 Q 48 1 STEP 1 STEP 2 B1 C F F1 A X A V V L L A V B C1 F F1 A X C1 B B1 F1 F A Y F Y Y F1 Y STEP 2: Attach Crossbeams 1 (Part B) and Crossbeams 4 (Part C1) to Pillars (Part A) . Attach Support Brackets ( Part F and F1) to Crossbeam and Pillar. Attach Crossbeams 2 Part B1) and Crossbeams 3 (Part C) to Pillars (Part A). Attach Support Brackets (Parts F and F1) to Cross Beam and Pillar C F F1 A STEP 3 up STEP 3:Connect the Ionger Crossbeams B and B1 using Crossbeam Connector (Part P) Note: After sliding the Crossbeam Connector (Part P) into a crossbeam you should start one bolt to hold the Crossbeam Connector in place. B C1 B1 P C A A V STEP 4 B1 P C1 C B B C1 B1 P C A A A A STEP 4: Stand both sides Upright and Connect Crossbeams B and crossbeams B1 using the Crossbeam Connectors (Part P) STEP 5-1 Y Y J1 YY B Y Y J1 C B1 B1 C1 B B C1 C B1 J2 STEP 5-1: Attach the Corner Protectors (Part J1) and the Rib Supports (Part J2) Just twist the top two screws of (Part J2) STEP 5-2 STEP 5-2: Slide 7 Netting Hooks (Part Q) into Long Crossbeams (Parts B and B1). With the sections laying on their side, Slide 5 Netting Hooks (Part Q) into Short Crossbeams (Parts C and C1). Then Attach (Part M6) Note: There are two tracks. You can choose either track to install Part Q B1 C1 C Q Y Y M6 Q B B C1 B1 M6 C A A A A Q Y Y M6 Q STEP 6 STEP 6: Assemble the Roof Frame by Attaching the Roof Ribs Long (Part E) to the Roof Top Brace (Part K1). K1 E E E E E K1 V V E E V E V STEP 7 E V STEP 8 D V STEP 9 D D D D D D V V V V V V D D D M8 H3 M8 V V X1 H3 D D D M8 D W M8 H3 D W D D W M8 W H3 M8 STEP 10 STEP 10: Attach the Clips (Part R1) and Clips (Part R) as shown in the diagram. R1 R R R1 R R R R R R R R1 R1 R R O1 O2 R R R R R R R R R1 R R O3 R1 R R1 R R N6 R R R R1 O5 O6 N7 R1 R R1 N8 R/R1 O4 R R R R R R R R Tap lightly with the screwdriver N1 N2 N3 N4 N5 STEP 11 N6 W N7 1 X1 O5 O6 3 4 K K1 M7 U M7 5 2 STEP 11Install the Roof Plates (Part N6 N7 N8) on the Long Sides of the Gazebo. Install the Roof Plates (Part O5 O6) on the Short Sides of the Gazebo. O5 O6 N6 N7 N8 STEP 12 G5 V STEP 12Tighten the screw (part U) halfwy,then install(Part G G5 G6 G7), and finally tighten the (Part U) G5 G6 M2 M1 G5 V V G7 G G6 G5 G G7 G5 G6 G G5/G6 G7/G G7 G6 STEP 13 V H1 STEP 13: Attach the Roof Supports (Part H H1 H2) to the roof frame using Connectors 1 (Part M3) and Connectors 2 (Part M4) as shown in the diagram M4 E H M4 H1 Please note that Parts M3 are installed on Parts D, and Parts M4 are on Parts E. V D H M3 H V H1 H2 M3 V H H M3 Don't tighten all the screws, just hold the(Part H and Part H1), until all of them are fixed H H H1 H2 W M3 M4 H1 STEP 14 W 1 S M5 2 21 2 4 3 12 4 3 N1 N2 N3 3 N4 T M5 T 3 N5 X1 X1 4 D STEP 14:Part N1 N2 N3 N4 N5 for the Long Sides of the Gazebo, Part O1 O2 O3 O4 for the short Sides of the Gazebo. Install the Roof Plates on the Long Sides of the Gazebo. Start by sliding Roof Plate 1 (Part N2 N3 N4) into position. Then N1and N4. The same for the other three sides. STEP 15 W S M5 2 X1 4 D T X1 O1 2 1 2 3 4 O2 3 O3 O4 M5 T 3 STEP 16 M2 Note: First fix 4 (Part M2) with V, but do not screw too tight, then install (Part G G1 G2 G3 and G4 )as shown in the diagram. You'd better from left to right. Attach the Center Rib Braces (PartM1) as shown in the diagram. M2 V G1/G2 G3/G4/G G1 G1 G2 G3 G G4 G1 M1 V G2 STEP 17 G3 U1 G3 M1 V G10 G G9 G G8 G10 STEP 17:Fix 4 U1 with V (just screw in a little), then install G G8 G9 and G10 from left to right as shown G8 G G9 V G9 G9 G10 STEP 18 STEP 18: Install the Mosquito Netting as Shown in the iagram. Q Z1 Z1 Z1 Z1Adobe Acrobat Pro 11.0.0