bannerengineering.com
Banner Engineering | Smarter Automation. Better Solutions.Patents
IO-Link - the First Globally Standardized IO TechnologyBanner Engineering | Smarter Automation. Better Solutions.
Instruction Manual for BANNER models including: SD50P300WKQP, SD50 IO-Link Status Display, SD50, IO-Link Status Display, Status Display, Display
Bachofen AG | BANNER Status Display SD50 - A487845 | purchase online
SD50P300WKQP | SD50 Status Display
File Info : application/pdf, 21 Pages, 1.09MB
DocumentDocumentSD50 with IO-Link Status Display Product Manual
Original Instructions p/n: 242037 Rev. A 14-Jan-25 © Banner Engineering Corp. All rights reserved.
SD50 with IO-Link Status Display Product Manual
Contents
Chapter 1 Features.................................................................................................................. 3
Models ........................................................................................................................................................................................................... 3
Chapter 2 Wiring...................................................................................................................... 4 Chapter 3 IO-Link Process Data Out (Master to Device) ..................................................... 5 Chapter 4 Specifications .......................................................................................................11
FCC Part 15 Class A for Unintentional Radiators .........................................................................................................................................11 Industry Canada ICES-003(A)......................................................................................................................................................................11 Dimensions .................................................................................................................................................................................................. 12
Chapter 5 Accessories.......................................................................................................... 13
Cordsets ...................................................................................................................................................................................................... 13 Mounting Brackets....................................................................................................................................................................................... 13
Chapter 6 Product Support and Maintenance .................................................................... 15
UTF-8 Encoding Table and Unicode Characters ......................................................................................................................................... 15 Clean with Mild Detergent and Water .......................................................................................................................................................... 19 Repairs ........................................................................................................................................................................................................ 19 Contact Us ................................................................................................................................................................................................... 20 Banner Engineering Corp Limited Warranty................................................................................................................................................ 20
© Banner Engineering Corp. All rights reserved.
SD50 With IO-Link Status Display Product Manual
Chapter Contents Models.................................................................................................................................................................................................................. 3
Chapter 1
Features
Provide More Status Information in the Most Helpful Locations
· Easily configurable, versatile display can be installed nearly anywhere, making it a simple yet powerful alternative to complex HMIs and other displays
· Great for displaying takt time, equipment status, assembly sequences, counts, and measurements where they are most useful
· Discrete and IO-Link models integrate into many different systems and applications, especially Banner sensing, safety, and monitoring solutions
· Quick and easy configuration--simply define the desired text and call it via discrete control or process data
· Bright white LED display and multicolored status LEDs legible from 10 meters away inform operators about exactly what is going on so they can respond quickly and accurately
· IP65-rated polycarbonate housing resists impact and condensation to provide clear communication in challenging and changing environmental conditions
Models
Model Key
Series SD
Height 50
Style P
Status Display
50 mm height
P = Pro
Display Length 300
Display Text Color W
Control K
300 = 300 mm
W = White
K = IO-Link
Connector(1)
QP
QP = 150 mm (6 in) PVC-jacketed cable with a 4-pin M12 male quickdisconnect connector
(1) Models with a quick-disconnect connector require a mating cordset.
14-Jan-25
© Banner Engineering Corp. All rights reserved.
page 3 of 21
SD50 With IO-Link Status Display Product Manual
Chapter Contents
Chapter 2
Wiring
SD50 with IO-Link Wiring
4-Pin Male M12 Pinout
1 2
4 3
Pinout Key and Wiring
1. Brown - 12 V DC to 30 V DC 2. White - Not used 3. Blue - DC Common 4. Black - IO-Link Communication
14-Jan-25
© Banner Engineering Corp. All rights reserved.
page 4 of 21
SD50 With IO-Link Status Display Product Manual
Chapter Contents
Chapter 3
IO-Link Process Data Out (Master to Device)
IO-Link® is a point-to-point communication link between a master device and a sensor and/or light. It can be used to automatically parameterize sensors or lights and to transmit process data. For the latest IO-LINK protocol and specifications, please visit www.io-link.com.
For the latest IODD files, please refer to the Banner Engineering Corp website at: www.bannerengineering.com.
Parameter Data Use Banner's IO-Link Master to configure the Parameter Data, which can configure the device's mode, display settings, and custom configurations.
Mode Select the mode for the device: Run Mode (default setting), Message Mode, Measure Mode, Timer Mode, Counter Mode, or Demo Mode.
Additional Settings Use Additional Settings to set the Indicator Intensity, Flash Rate, Display Intensity, and Scroll Speed to custom values that are unique from the standard options.
Custom Color Configuration Use Custom Color Configuration to control the colors of the indicator LEDs using RGB codes ranging from 0-255.
Device Access Locks
14-Jan-25
© Banner Engineering Corp. All rights reserved.
page 5 of 21
SD50 with IO-Link Status Display Product Manual
IO-Link Process Data Out (Master to Device)
Use Device Access Locks to lock or unlock Parameter Write Access and Data Storage Access.
Display Settings Use Display Settings to configure the color, intensity, direction, speed, scroll mode, orientation, and justification of the display text.
General Settings Display Text Color Display Intensity Display Control Direction Display Scroll Speed Display Scroll Mode Display Orientation Display Justification
Description Select either white or black display text. Define the intensity of the display text with a set of preset values or a custom value. Select the direction the display text scrolls, using the connector as a reference. Define the speed at which the display text scrolls using a set of preset values or a custom value. Determine if the device scrolls the text. Auto scrolls the text for inputs longer than 16 characters. Select the orientation of the device, using the connector as a reference. The text and display rotate to match the device's orientation. Select the justification of the display text between Left, Right, or Center.
Restore Factory Settings Use Restore Factory Settings to clear the current configurations and reset the device to its initial settings.
Measure Base Settings Use Measure Base Settings to configure the overall settings of the display device in Measure Mode.
General Settings Display Override Override String Animation Color 1 Color 1 Intensity Configuration Speed Pulse Pattern Color 2 Color 2 Intensity
Description Determine if the device displays a string of text rather than the output values. Determine the text that displays if Display Override is enabled. Select the animation of the indicator LEDs from the animation table. Select the color of the first row of indicator LEDs. Define the intensity of the first row of indicator LEDs. Define the speed of the animation. Select the pulse pattern of the indicator LEDs: Normal, Strobe, Three Pulse, SOS, or Random. Select the color of the first row of indicator LEDs. Define the intensity of the first row of indicator LEDs.
Measure Mode Settings Use the Process Data to display the measurement values. Options include either the raw input values or the scaled values.
page 6 of 21
© Banner Engineering Corp. All rights reserved.
14-Jan-25
IO-Link Process Data Out (Master to Device)
SD50 with IO-Link Status Display Product Manual
General Settings
Description
Filtering
The level of filtering used to minimize the effects of noise on the output.
Hysteresis
The level of lag between the measurement thresholds to minimize the flickering at switch points.
Measure/Timer/Counter Mode Data Label
Text that displays before the Count Value.
Measure/Timer/Counter Mode Bar Graph
Display the bar graph across the full display.
Output Scale Value Low
The low-end value of the output translated from the input frequency.
Output Scale Value High
The high-end value of the output translated from the input frequency.
Input Scale Value Low
The lowest frequency of the input range.
Input Scale Value High
The highest frequency of the input range.
Measure/Timer/Counter Mode Value Label
Text that displays after the Count Value to indicate the units displayed. This can be up to three characters.
Measure General Configuration.Measure/Timer/Counter Mode Display Orientation
Determine the orientation of the bar graph, using the connector as a reference.
Measure General Configuration.Measure/Timer/Counter Mode Display Minimal Bar Graph
Display the bar graph as a single line of LEDs.
Measure General Configuration.Measure/Timer/Counter Mode Decimal Places
Determine the number of decimal places displayed on the Count Value.
Measure General Configuration.Measure/Timer/Counter Mode Display as Time
Display the time in HH:MM:SS format without data labels.
Message Mode Use Message Mode to create and save thirteen display messages.
Threshold Settings Use Threshold Settings to configure the thresholds using in Measure Mode, Timer Mode, and Counter Mode. Four of these thresholds can be set individually.
14-Jan-25
© Banner Engineering Corp. All rights reserved.
page 7 of 21
SD50 with IO-Link Status Display Product Manual
IO-Link Process Data Out (Master to Device)
General Settings Threshold Enable Threshold Value Threshold Comparison Threshold Override
Description Determine if thresholds will be used to change the output at various levels. Define the percentage of the overall value that sets the threshold based on the threshold number used. Determine if this threshold is in use for values greater than or less than the Threshold Value. Determine the precedence of the thresholds that have overlapping criteria.
General Settings Display Override Override String Animation Color Color Intensity Configuration Speed Pulse Pattern
Description Determine if the device displays a string of text rather than the output values. Determine the text that displays if Display Override is enabled. Select the animation of the indicator LEDs from the animation table. Select the color of the indicator LEDs. Define the intensity of the indicator LEDs. Define the speed of the animation. Select the pulse pattern of the indicator LEDs: Normal, Strobe, Three Pulse, SOS, or Random.
Timer Mode Use Timer Mode to count up to or down from a determined value. For additional timer settings, refer to the table in Measure Mode Settings.
General Settings Timer Value Timer Unit Type Timer Count Type Enable Auto Reload
Description The total time of the timer. Select the units of the timer. Up: Counts up from zero to Count Seconds. Down: Counts down from Count Seconds to zero. The timer loops back to the original value automatically when it reaches its final value.
Counter Mode Counter Mode uses parameter settings found in Measure Mode Settings to configure the output of the device. For more detail, refer to the table in Measure Mode Settings.
Demo Mode Demo sequence cycles through twelve different configurations to highlight example applications.
Process Data Process Data is used to implement the data to run the device. With Process Data, the selection menu changes based on the Mode Selection written to the device.
page 8 of 21
© Banner Engineering Corp. All rights reserved.
14-Jan-25
IO-Link Process Data Out (Master to Device)
SD50 with IO-Link Status Display Product Manual
Run Mode Message Mode
Measure Mode
14-Jan-25
© Banner Engineering Corp. All rights reserved.
page 9 of 21
SD50 with IO-Link Status Display Product Manual
Timer Mode
IO-Link Process Data Out (Master to Device)
Counter Mode
Indicator LED Animations
Animation Off Steady Flash Two Color Flash 50/50 50/50 Flash Intensity Sweep
Two Color Sweep
Description Indication LEDs are off. Color 1 is solid on at a defined intensity. Color 1 flashes alternately at defined speed, color intensities, and pattern (Normal, Strobe, Three Pulse, SOS, or Random). Color 1 and Color 2 flash alternately at defined speed, color intensities, and pattern (Normal, Strobe, Three Pulse, SOS, or Random). Color 1 and Color 2 are solid at a defined intensity. Color 1 and Color 2 flash at a defined speed, color intensity, and pattern (Normal, Strobe, Three Pulse, SOS, or Random). Color 1 repeatedly increases and decreases intensity between 0% to 100% at defined speed and color intensity. Color 1 and Color 2 define the end values of a line across the color gamut. The light continuously displays a color by moving along the line at the defined speed and color intensities.
page 10 of 21
© Banner Engineering Corp. All rights reserved.
14-Jan-25
SD50 With IO-Link Status Display Product Manual
Chapter Contents
FCC Part 15 Class A for Unintentional Radiators................................................................................................................................................11 Industry Canada ICES-003(A).............................................................................................................................................................................11 Dimensions......................................................................................................................................................................................................... 12
Chapter 4
Specifications
Supply Voltage 12 V DC to 30 V DC
Use only with a suitable Class 2 power supply (UL) or SELV power supply (CE)
Supply Current 550 mA max. at 12 V DC 260 mA max. at 24 V DC 210 mA max. at 30 V DC
Connections 150 mm (6 in) PVC-jacketed cable with a 4-pin M12 male quick-disconnect connector
Models with a quick-disconnect connector require a mating cordset
Do not spray cable with high-pressure sprayer or cable damage will result
Operating Temperature 20 °C to +50 °C (4 °F to +122 °F)
Storage Temperature 40 °C to +70 °C (40 °F to +158 °F)
Environmental Rating Rated IP65
Suitable for damp locations per UL 2108
Vibration and Mechanical Shock Meets IEC 60068-2-6 requirements (Vibration: 10 Hz to 55 Hz, 1.0 mm amplitude, 5 minutes sweep, 30 minutes dwell)
Meets IEC 60068-2-27 requirements (Shock: 15G 11 ms duration, half sine wave)
Construction Black polycarbonate housing and end caps Internal silicone-encapsulated LEDs Smoky polycarbonate window
Required Overcurrent Protection
WARNING: Electrical connections must be made by qualified personnel in accordance with local and national
electrical codes and regulations.
Overcurrent protection is required to be provided by end product application per the supplied table.
Overcurrent protection may be provided with external fusing or via Current Limiting, Class 2 Power Supply.
Supply wiring leads < 24 AWG shall not be spliced.
For additional product support, go to www.bannerengineering.com.
Supply Wiring (AWG)
20
22
24
Required Overcurrent Protection (A)
5.0 3.0 1.0
Supply Wiring (AWG)
26
28
30
Required Overcurrent Protection (A)
1.0 0.8 0.5
Mounting M5 and 1/4-20 compatible end caps (not included) Clip brackets for mounting are available
FCC Part 15 Class A for Unintentional Radiators
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
(Part 15.21) Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
Industry Canada ICES-003(A)
This device complies with CAN ICES-3 (A)/NMB-3(A). Operation is subject to the following two conditions: 1) This device may not cause harmful interference; and 2) This device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la norme NMB-3(A). Le fonctionnement est soumis aux deux conditions suivantes : (1) ce dispositif ne peut pas occasionner d'interférences, et (2) il doit tolérer toute interférence, y compris celles susceptibles de provoquer un fonctionnement non souhaité du dispositif.
14-Jan-25
© Banner Engineering Corp. All rights reserved.
page 11 of 21
SD50 with IO-Link Status Display Product Manual
Specifications
Dimensions
All measurements are listed in millimeters [inches], unless noted otherwise. The measurements provided are subject to change.
51.3 [2.02]
27.7 [1.09]
4X 5.5 [0.22]
4X 11.2 [0.44]
SD50..300..
Models
L2 L1
385.5 [15.18]
M12 x 1.0
13.8 [0.54]
20.7 [0.81]
L1 300 mm (11.81 in)
4X 5.5 [0.22]
4X 5.7 [0.22]
L2 325 mm (12.8 in)
page 12 of 21
© Banner Engineering Corp. All rights reserved.
14-Jan-25
SD50 With IO-Link Status Display Product Manual
Chapter Contents
Cordsets ............................................................................................................................................................................................................. 13 Mounting Brackets.............................................................................................................................................................................................. 13
Chapter 5
Accessories
Cordsets
Model MQDEC-401SS MQDEC-402SS MQDEC-403SS MQDEC-406SS
MQDEC-410SS
Length 0.31 m (1 ft) 0.6 m (1.97 ft) 0.91 m (2.99 ft) 1.83 m (6 ft)
3 m (9.4 ft)
4-Pin Threaded M12 Cordsets--Double Ended
Style
Dimensions
40 Typ. [1.58"]
Male Straight/ Female Straight
M12 x 1 ø 14.5 [0.57"]
44 Typ. [1.73"]
M12 x 1 ø 14.5 [0.57"]
Pinout
Female
2 1
3 4
Male
1 2
4 3
1 = Brown 2 = White 3 = Blue 4 = Black
Mounting Brackets
LMBSD50 · Metal mounting bracket kit · Hardware included
LMBSD50MAG · Magnetic mounting bracket kit · Up to 7.26 kg (16 lb) pull · Hardware included
LMBSD50-180S · Metal mounting bracket kit with 180-degree rotation · Stainless steel · Hardware included
Ø6.5
14.5 49
20
22 Ø36
20
50
45 Ø6.4
14.5 50
14-Jan-25
© Banner Engineering Corp. All rights reserved.
page 13 of 21
SD50 with IO-Link Status Display Product Manual
LMBSD50-180SMAG · Magnetic mounting bracket kit with 180-degree rotation · Stainless steel · Up to 7.26 kg (16 lb) pull · Hardware included
Accessories
52
50
20
Ø52
page 14 of 21
© Banner Engineering Corp. All rights reserved.
14-Jan-25
SD50 With IO-Link Status Display Product Manual
Chapter Contents
UTF-8 Encoding Table and Unicode Characters................................................................................................................................................ 15 Clean with Mild Detergent and Water................................................................................................................................................................. 19 Repairs ............................................................................................................................................................................................................... 19 Contact Us.......................................................................................................................................................................................................... 20 Banner Engineering Corp Limited Warranty....................................................................................................................................................... 20
Chapter 6
Product Support and Maintenance
UTF-8 Encoding Table and Unicode Characters
Unicode Code Point
U+0020
U+0021
!
U+0022
"
U+0023
#
U+0024
$
U+0025
%
U+0026
&
U+0027
'
U+0028
(
U+0029
)
U+002A
*
U+002B
+
U+002C
,
U+002D
-
U+002E
.
U+002F
/
U+0030
0
U+0031
1
U+0032
2
U+0033
3
U+0034
4
U+0035
5
U+0036
6
U+0037
7
U+0038
8
U+0039
9
U+003A
:
U+003B
;
U+003C
<
U+003D
=
U+003E
>
Character
UTF-8 (hex.) 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a 3b 3c 3d 3e
Continued on page 16
SPACE EXCLAMATION MARK QUOTATION MARK NUMBER SIGN DOLLAR SIGN PERCENT SIGN AMPERSAND APOSTROPHE LEFT PARENTHESIS RIGHT PARENTHESIS ASTERISK PLUS SIGN COMMA HYPHEN-MINUS FULL STOP SOLIDUS DIGIT ZERO DIGIT ONE DIGIT TWO DIGIT THREE DIGIT FOUR DIGIT FIVE DIGIT SIX DIGIT SEVEN DIGIT EIGHT DIGIT NINE COLON SEMICOLON LESS-THAN SIGN EQUALS SIGN GREATER-THAN SIGN
Name
14-Jan-25
© Banner Engineering Corp. All rights reserved.
page 15 of 21
SD50 with IO-Link Status Display Product Manual
Unicode Code Point
U+003F
?
U+0040
@
U+0041
A
U+0042
B
U+0043
C
U+0044
D
U+0045
E
U+0046
F
U+0047
G
U+0048
H
U+0049
I
U+004A
J
U+004B
K
U+004C
L
U+004D
M
U+004E
N
U+004F
O
U+0050
P
U+0051
Q
U+0052
R
U+0053
S
U+0054
T
U+0055
U
U+0056
V
U+0057
W
U+0058
X
U+0059
Y
U+005A
Z
U+005B
[
U+005C
\
U+005D
]
U+005E
^
U+005F
_
U+0060
`
U+0061
a
U+0062
b
U+0063
c
U+0064
d
U+0065
e
U+0066
f
U+0067
g
U+0068
h
Character
Product Support and Maintenance
Continued from page 15 UTF-8 (hex.)
Name
3f
QUESTION MARK
40
COMMERCIAL AT
41
LATIN CAPITAL LETTER A
42
LATIN CAPITAL LETTER B
43
LATIN CAPITAL LETTER C
44
LATIN CAPITAL LETTER D
45
LATIN CAPITAL LETTER E
46
LATIN CAPITAL LETTER F
47
LATIN CAPITAL LETTER G
48
LATIN CAPITAL LETTER H
49
LATIN CAPITAL LETTER I
4a
LATIN CAPITAL LETTER J
4b
LATIN CAPITAL LETTER K
4c
LATIN CAPITAL LETTER L
4d
LATIN CAPITAL LETTER M
4e
LATIN CAPITAL LETTER N
4f
LATIN CAPITAL LETTER O
50
LATIN CAPITAL LETTER P
51
LATIN CAPITAL LETTER Q
52
LATIN CAPITAL LETTER R
53
LATIN CAPITAL LETTER S
54
LATIN CAPITAL LETTER T
55
LATIN CAPITAL LETTER U
56
LATIN CAPITAL LETTER V
57
LATIN CAPITAL LETTER W
58
LATIN CAPITAL LETTER X
59
LATIN CAPITAL LETTER Y
5a
LATIN CAPITAL LETTER Z
5b
LEFT SQUARE BRACKET
5c
REVERSE SOLIDUS
5d
RIGHT SQUARE BRACKET
5e
CIRCUMFLEX ACCENT
5f
LOW LINE
60
GRAVE ACCENT
61
LATIN SMALL LETTER A
62
LATIN SMALL LETTER B
63
LATIN SMALL LETTER C
64
LATIN SMALL LETTER D
65
LATIN SMALL LETTER E
66
LATIN SMALL LETTER F
67
LATIN SMALL LETTER G
68 Continued on page 17
LATIN SMALL LETTER H
page 16 of 21
© Banner Engineering Corp. All rights reserved.
14-Jan-25
Product Support and Maintenance
Unicode Code Point
U+0069
i
U+006A
j
U+006B
k
U+006C
l
U+006D
m
U+006E
n
U+006F
o
U+0070
p
U+0071
q
U+0072
r
U+0073
s
U+0074
t
U+0075
u
U+0076
v
U+0077
w
U+0078
x
U+0079
y
U+007A
z
U+007B
{
U+007C
|
U+007D
}
U+007E
~
U+00A0
U+00A1
¡
U+00A2
¢
U+00A3
£
U+00A4
¤
U+00A5
¥
U+00A6
¦
U+00A7
§
U+00A8
¨
U+00A9
©
U+00AA
ª
U+00AB
«
U+00AC
¬
U+00AD
U+00AE
®
U+00AF
¯
U+00B0
°
U+00B1
±
U+00B2
²
U+00B3
³
Character
SD50 with IO-Link Status Display Product Manual
Continued from page 16 UTF-8 (hex.)
Name
69
LATIN SMALL LETTER I
6a
LATIN SMALL LETTER J
6b
LATIN SMALL LETTER K
6c
LATIN SMALL LETTER L
6d
LATIN SMALL LETTER M
6e
LATIN SMALL LETTER N
6f
LATIN SMALL LETTER O
70
LATIN SMALL LETTER P
71
LATIN SMALL LETTER Q
72
LATIN SMALL LETTER R
73
LATIN SMALL LETTER S
74
LATIN SMALL LETTER T
75
LATIN SMALL LETTER U
76
LATIN SMALL LETTER V
77
LATIN SMALL LETTER W
78
LATIN SMALL LETTER X
79
LATIN SMALL LETTER Y
7a
LATIN SMALL LETTER Z
7b
LEFT CURLY BRACKET
7c
VERTICAL LINE
7d
RIGHT CURLY BRACKET
7e
TILDE
c2 a0
NO-BREAK SPACE
c2 a1
INVERTED EXCLAMATION MARK
c2 a2
CENT SIGN
c2 a3
POUND SIGN
c2 a4
CURRENCY SIGN
c2 a5
YEN SIGN
c2 a6
BROKEN BAR
c2 a7
SECTION SIGN
c2 a8
DIAERESIS
c2 a9
COPYRIGHT SIGN
c2 aa
FEMININE ORDINAL INDICATOR
c2 ab
LEFT-POINTING DOUBLE ANGLE QUOTATION MARK
c2 ac
NOT SIGN
c2 ad
SOFT HYPHEN
c2 ae
REGISTERED SIGN
c2 af
MACRON
c2 b0
DEGREE SIGN
c2 b1
PLUS-MINUS SIGN
c2 b2
SUPERSCRIPT TWO
c2 b3 Continued on page 18
SUPERSCRIPT THREE
14-Jan-25
© Banner Engineering Corp. All rights reserved.
page 17 of 21
SD50 with IO-Link Status Display Product Manual
Unicode Code Point
U+00B4
´
U+00B5
µ
U+00B6
¶
U+00B7
·
U+00B8
¸
U+00B9
¹
U+00BA
º
U+00BB
»
U+00BC
¼
U+00BD
½
U+00BE
¾
U+00BF
¿
U+00C0
À
U+00C1
Á
U+00C2
Â
U+00C3
Ã
U+00C4
Ä
U+00C5
Å
U+00C6
Æ
U+00C7
Ç
U+00C8
È
U+00C9
É
U+00CA
Ê
U+00CB
Ë
U+00CC
Ì
U+00CD
Í
U+00CE
Î
U+00CF
Ï
U+00D0
Ð
U+00D1
Ñ
U+00D2
Ò
U+00D3
Ó
U+00D4
Ô
U+00D5
Õ
U+00D6
Ö
U+00D7
×
U+00D8
Ø
U+00D9
Ù
U+00DA
Ú
U+00DB
Û
U+00DC
Ü
U+00DD
Ý
Character
Product Support and Maintenance
Continued from page 17 UTF-8 (hex.)
Name
c2 b4
ACUTE ACCENT
c2 b5
MICRO SIGN
c2 b6
PILCROW SIGN
c2 b7
MIDDLE DOT
c2 b8
CEDILLA
c2 b9
SUPERSCRIPT ONE
c2 ba
MASCULINE ORDINAL INDICATOR
c2 bb
RIGHT-POINTING DOUBLE ANGLE QUOTATION MARK
c2 bc
VULGAR FRACTION ONE QUARTER
c2 bd
VULGAR FRACTION ONE HALF
c2 be
VULGAR FRACTION THREE QUARTERS
c2 bf
INVERTED QUESTION MARK
c3 80
LATIN CAPITAL LETTER A WITH GRAVE
c3 81
LATIN CAPITAL LETTER A WITH ACUTE
c3 82
LATIN CAPITAL LETTER A WITH CIRCUMFLEX
c3 83
LATIN CAPITAL LETTER A WITH TILDE
c3 84
LATIN CAPITAL LETTER A WITH DIAERESIS
c3 85
LATIN CAPITAL LETTER A WITH RING ABOVE
c3 86
LATIN CAPITAL LETTER AE
c3 87
LATIN CAPITAL LETTER C WITH CEDILLA
c3 88
LATIN CAPITAL LETTER E WITH GRAVE
c3 89
LATIN CAPITAL LETTER E WITH ACUTE
c3 8a
LATIN CAPITAL LETTER E WITH CIRCUMFLEX
c3 8b
LATIN CAPITAL LETTER E WITH DIAERESIS
c3 8c
LATIN CAPITAL LETTER I WITH GRAVE
c3 8d
LATIN CAPITAL LETTER I WITH ACUTE
c3 8e
LATIN CAPITAL LETTER I WITH CIRCUMFLEX
c3 8f
LATIN CAPITAL LETTER I WITH DIAERESIS
c3 90
LATIN CAPITAL LETTER ETH
c3 91
LATIN CAPITAL LETTER N WITH TILDE
c3 92
LATIN CAPITAL LETTER O WITH GRAVE
c3 93
LATIN CAPITAL LETTER O WITH ACUTE
c3 94
LATIN CAPITAL LETTER O WITH CIRCUMFLEX
c3 95
LATIN CAPITAL LETTER O WITH TILDE
c3 96
LATIN CAPITAL LETTER O WITH DIAERESIS
c3 97
MULTIPLICATION SIGN
c3 98
LATIN CAPITAL LETTER O WITH STROKE
c3 99
LATIN CAPITAL LETTER U WITH GRAVE
c3 9a
LATIN CAPITAL LETTER U WITH ACUTE
c3 9b
LATIN CAPITAL LETTER U WITH CIRCUMFLEX
c3 9c
LATIN CAPITAL LETTER U WITH DIAERESIS
c3 9d Continued on page 19
LATIN CAPITAL LETTER Y WITH ACUTE
page 18 of 21
© Banner Engineering Corp. All rights reserved.
14-Jan-25
Product Support and Maintenance
Unicode Code Point
U+00DE
Þ
U+00DF
ß
U+00E0
à
U+00E1
á
U+00E2
â
U+00E3
ã
U+00E4
ä
U+00E5
å
U+00E6
æ
U+00E7
ç
U+00E8
è
U+00E9
é
U+00EA
ê
U+00EB
ë
U+00EC
ì
U+00ED
í
U+00EE
î
U+00EF
ï
U+00F0
ð
U+00F1
ñ
U+00F2
ò
U+00F3
ó
U+00F4
ô
U+00F5
õ
U+00F6
ö
U+00F7
÷
U+00F8
ø
U+00F9
ù
U+00FA
ú
U+00FB
û
U+00FC
ü
U+00FD
ý
U+00FE
þ
U+00FF
ÿ
Character
SD50 with IO-Link Status Display Product Manual
Continued from page 18 UTF-8 (hex.)
Name
c3 9e
LATIN CAPITAL LETTER THORN
c3 9f
LATIN SMALL LETTER SHARP S
c3 a0
LATIN SMALL LETTER A WITH GRAVE
c3 a1
LATIN SMALL LETTER A WITH ACUTE
c3 a2
LATIN SMALL LETTER A WITH CIRCUMFLEX
c3 a3
LATIN SMALL LETTER A WITH TILDE
c3 a4
LATIN SMALL LETTER A WITH DIAERESIS
c3 a5
LATIN SMALL LETTER A WITH RING ABOVE
c3 a6
LATIN SMALL LETTER AE
c3 a7
LATIN SMALL LETTER C WITH CEDILLA
c3 a8
LATIN SMALL LETTER E WITH GRAVE
c3 a9
LATIN SMALL LETTER E WITH ACUTE
c3 aa
LATIN SMALL LETTER E WITH CIRCUMFLEX
c3 ab
LATIN SMALL LETTER E WITH DIAERESIS
c3 ac
LATIN SMALL LETTER I WITH GRAVE
c3 ad
LATIN SMALL LETTER I WITH ACUTE
c3 ae
LATIN SMALL LETTER I WITH CIRCUMFLEX
c3 af
LATIN SMALL LETTER I WITH DIAERESIS
c3 b0
LATIN SMALL LETTER ETH
c3 b1
LATIN SMALL LETTER N WITH TILDE
c3 b2
LATIN SMALL LETTER O WITH GRAVE
c3 b3
LATIN SMALL LETTER O WITH ACUTE
c3 b4
LATIN SMALL LETTER O WITH CIRCUMFLEX
c3 b5
LATIN SMALL LETTER O WITH TILDE
c3 b6
LATIN SMALL LETTER O WITH DIAERESIS
c3 b7
DIVISION SIGN
c3 b8
LATIN SMALL LETTER O WITH STROKE
c3 b9
LATIN SMALL LETTER U WITH GRAVE
c3 ba
LATIN SMALL LETTER U WITH ACUTE
c3 bb
LATIN SMALL LETTER U WITH CIRCUMFLEX
c3 bc
LATIN SMALL LETTER U WITH DIAERESIS
c3 bd
LATIN SMALL LETTER Y WITH ACUTE
c3 be
LATIN SMALL LETTER THORN
c3 bf
LATIN SMALL LETTER Y WITH DIAERESIS
Clean with Mild Detergent and Water
Wipe down the enclosure and the display with a soft cloth that has been dampened with a mild detergent and warm water solution.
Repairs
Contact Banner Engineering for troubleshooting of this device. Do not attempt any repairs to this Banner device; it contains no field-replaceable parts or components. If the device, device part, or device component is determined to be defective by a Banner Applications Engineer, they will advise you of Banner's RMA (Return Merchandise Authorization) procedure.
14-Jan-25
© Banner Engineering Corp. All rights reserved.
page 19 of 21
SD50 with IO-Link Status Display Product Manual
Product Support and Maintenance
IMPORTANT: If instructed to return the device, pack it with care. Damage that occurs in return shipping is not covered by warranty.
Contact Us
Banner Engineering Corp. headquarters is located at: 9714 Tenth Avenue North | Plymouth, MN 55441, USA | Phone: + 1 888 373 6767
For worldwide locations and local representatives, visit www.bannerengineering.com.
Banner Engineering Corp Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to: www.bannerengineering.com.
For patent information, see www.bannerengineering.com/patents.
page 20 of 21
© Banner Engineering Corp. All rights reserved.
14-Jan-25
LinkedIn X (formerly Twitter) Facebook
© 2025. All rights reserved. www.bannerengineering.com