Vanco International | Leading Supplier of Electronic AccessoriesPulseAudio - Vanco International
User Manual for PULSEAUDIO models including: PAEXARC1 ARC Digital Audio Extender, PAEXARC1, ARC Digital Audio Extender, Digital Audio Extender, Audio Extender, Extender
ARC Digital Audio Extender - Vanco International
File Info : application/pdf, 8 Pages, 422.20KB
DocumentDocumentARC DIGITAL AUDIO EXTENDER PAEXARC1 For applications where ARC signals need to be extended above HDMI cabling limitations to an amplifier or distributed audio system. Updated: May 2023 SAFETY INSTRUCTIONS For optimum performance and safety, please read these instructions carefully before use. Please keep this manual for future reference. · To prevent electric shock, please ensure that all apparatus is properly grounded. · Place the device in a well-ventilated area, do not block any ventilation openings. · Do not expose this apparatus to rain or place it near water. Any liquid that goes into the apparatus may cause a failure, fire, or electric shock. · Do not place the device on an uneven or unstable surface. The device may fall resulting in a malfunction. · Never insert anything metallic into the open parts of this apparatus. This may cause a danger of electric shock. · If a third-party power supply is used, please ensure that the power supply specifications meet the product requirements. INTRODUCTION The PulseAudio PAEXARC1 is an ARC Digital Audio Extender that allows digital audio to be routed from a display, back to a remote location or amplifier, over a single Cat5e/6 cable up to 492ft (150m). For displays without ARC capability, or when ARC settings are not working as they should, the built-in "ARC Backup Plan" is featured where audio can still be extended utilizing SPDIF. For applications where ARC signals need to be extended above HDMI cabling limitations to an amplifier or distributed audio system, the PAEXARC1 is the perfect solution. The range of the PAXEARC1 will vary depending on the HDMI/ARC sample rates. For instance, higher sample rates, 192kHz, will be rated at 295ft (90m), while lower sample rates, 96kHz, will be rated at 492ft (150m). Product Features · Extends ARC Digital Audio signals over Cat5e/6 · Supports a single HDMI ARC input and output · Extends digital audio signals up to 492ft (150m) at 96kHz or 295ft (90m) at 192kHz over a single Cat5e/6 · Built-in "ARC Backup Plan" with SPDIF input and output · Supports Dolby / DTS 5.1CH and PCM 2CH audio formats · CEC pass-through when HDMI® ARC mode is enabled · Dimensions: 3.5" x 2.8" x 0.8" (90mm x 72mm x 20mm) · Weight: 6.2oz (175g) Package Contents (1) Digital audio extender set - TX and RX (2) 5V 2A USB power sdapters (2) USB-A to micro-USB cables (1) Product manual SPECIFICATIONS Audio Supported Audio Formats PCM 2CH, Dolby/DTS 5.1CH Sample Rates Optical / ARC (492ft / 150m) 32kHz, 44.1kHz, 48kHz, 88.2kHz, 96kHz ARC (295ft / 90m) 32kHz, 44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz Connections Transmitter Input: (1) SPDIF, (1) ARC HDMI® In, (1) Micro-USB (Power) Output: (1) CAT Out (Cat5e/6) Receiver Input: (1) CAT In (Cat5e/6), (1) Micro-USB (Power) Output: (1) SPDIF Out, (1) ARC HDMI® Out Technical & Mechanical Housing Metal Color Black Dimensions 3.5" x 2.8" x 0.8" (90mm x 72mm x 20mm) Weight 6.2oz / 175g Power Power Consumption Transmitter: .35W Receiver: .7W Human-body Model: ±8kV (Air-gap discharge) ESD ±4kV (Contact discharge) Operating Environment Temperature Working: 0°C to 40°C / 32°F to 104°F Storage: -20 to 60°C / -4°F to 140°F Relative Humidity 20 to 90% RH (Non-condensing) PANEL DESCRIPTIONS Transmitter Panel 1. POWER LED: When the transmitter is receiving power, the LED light will be red. 2. SPDIF/ARC SWITCH: Selects the audio pass-through channel: SPDIF: Digital audio signals are input from the SPDIF IN port of the Transmitter ARC: Digital audio signals are input from the HDMI ARC IN port of the Transmitter. 3. CAT OUT: Connect a single Cat5e/6 cable from the transmitting unit to the receiving unit (home-run cabling strongly recommended without any couplings, punch-downs, or patch panels). 4. SPDIF IN: Connect to an optical audio source device with an optical toslink cable. 5. ARC IN: Connect to a TV with ARC functionality for ARC audio and CEC passthrough. NOTE: Ensure this is connected to the display's ARC HDMI port, and that the option for ARC is enabled within the display options. 6. DC 5V: Plug in the included Micro USB power cable for power. 1 2 3 4 5 6 Receiver Panel 1. POWER LED: When the receiver is receiving power, the LED light will be red. 2. CAT IN: Connect a single Cat5e/6 cable from the transmitting unit to the Receiving Unit (home-run cabling strongly recommended without any couplings, punchdowns, or patch panels). 3. SPDIF OUT: Connect to a speaker or amplifier with an optical toslink cable. 4. ARC OUT: Connect to an audio device with ARC such as a soundbar, amplifier, or AV receiver. 5. DC 5V: Plug in the included Micro USB power cable for power. 1 2 3 4 5 OPERATION HDMI ARC For Displays and Amplifiers/Soundbars with ARC functionality 1. Connect an ARC equipped display such as an HDTV or HD Projector using the ARC HDMI port of the display to the HDMI input on the Transmitting Unit and set the SPDIF/ARC toggle switch to ARC. NOTE: Please refer to the displays manual on how to enable ARC settings. 2. Connect an amplifier, AV receiver, or soundbar to the HDMI output on the Receiving Unit. NOTE: If there are multiple HDMI ports on the audio device connected to the receiver, make sure it is connected to the HDMI port labeled ARC. Refer to the device's manual if additional ARC settings need to be enabled. 3. Connect a single Cat5e/6 to the CAT OUT port of the Transmitting Unit, and the other end to the CAT IN port of the Receiving unit (home-run cabling strongly recommended without any couplings, punch-downs, or patch panels). 4. For power, plug the Transmitting Unit and Receiving Unit with the included USB power cables and adapters. 5. Power on and test (Transmitter and Receiver Units will already be powered when either unit is plugged in). HDMI® Cat5e/6 HDMI® HDTV Transmitter Receiver Amplifier SPDIF Digital Audio 1. Connect an optical audio out port from a display such as an HDTV or HD Projector to the SPDIF IN port on the Transmitting unit, and set the SPDIF/ARC toggle switch to SPDIF. NOTE: Please refer to the displays manual on how to enable or change audio output settings. 2. Connect an amplifier, AV receiver, or soundbar to the SPDIF OUT port on the receiving unit. 3. Connect a single Cat5e/6 to the CAT OUT port of the Transmitting Unit, and the other end to the CAT IN port of the Receiving Unit 4. For power, plug the Transmitting Unit and Receiving Unit with the included USB power cables and adapters. 5. Power on and test (Transmitter and Receiver Units will already be powered when either unit is plugged in). Optical Audio Cat5e/6 Optical Audio HDTV Transmitter Receiver Amplifier LIMITED WARRANTY With the exceptions noted in the next paragraph, Vanco warrants to the original purchaser that the equipment it manufactures or sells will be free from defects in materials and workmanship for a period of 2 years from the date of purchase. Should this product, in Vanco's opinion, prove defective within this warranty period, Vanco, at its option, will repair or replace this product without charge. Any defective parts replaced become the property of Vanco. This warranty does not apply to those products which have been damaged due to accident, unauthorized alterations, improper repair, modifications, inadequate maintenance and care, or use in any manner for which the product was not originally intended. Items integrated into Vanco products that are made by other manufacturers, notably computer hard drives and liquid crystal display panels, are limited to the term of the warranty offered by the respective manufacturers. Such specific warranties are available upon request to Vanco. A surge protector, power conditioner unit, or an uninterruptible power supply must be installed in the electrical circuit to protect against power surges. If repairs are needed during the warranty period the purchaser will be required to provide a sales receipt/sales invoice or other acceptable proof of purchase to the seller of this equipment. The seller will then contact Vanco regarding warranty repair or replacement. LIABILITY STATEMENT Every effort has been made to ensure that this product is free of defects. The manufacturer of this product cannot be held liable for the use of this hardware or any direct or indirect consequential damages arising from its use. It is the responsibility of the user and installer of the hardware to check that it is suitable for their requirements and that it is installed correctly. All rights are reserved. No parts of this manual may be reproduced or transmitted by any form or means electronic or mechanical, including photocopying, recording or by any information storage or retrieval system without the written consent of the publisher. Manufacturer reserves the right to revise any of its hardware and software following its policy to modify and/or improve its products where necessary or desirable. This statement does not affect the legal rights of the user in any way. TECHNICAL SUPPORT In case of problems, please contact Vanco Technical Support by dialing 1-800-626-6445. You can also email technical support issues to techsupport@vanco1.com. When calling, please have the part number, serial number (affixed to the bottom of the unit) and invoice available for reference during the call. Please read this instruction manual prior to calling or installing this unit, since it will familiarize you with the capabilities of this product and its proper installation. All active electronic products are 100% inspected and tested to insure highest product quality and trouble-free installation and operation. The testing process utilizes the types of high-definition sources and displays typically installed for entertainment and home theater applications. For additional information, please visit www.vanco1.com. Updated: May 2023 TECHNICAL SUPPORT Phone: 1-800-626-6445 Email: techsupport@vanco1.com Web: www.vanco1.com Please have the part number, serial number, and invoice available for reference. Please read this instruction manual prior to calling or installing this unit since it will familiarize you with the capabilities of this product and its proper installation. Vanco International, LLC 506 Kingsland Dr., Batavia, IL 60510 USA Phone: 800-626-6445 · Fax: 630-879-9189 Web: www.vanco1.com