User Guide for kramer models including: KDS AVoIP Switcher Encoder, AVoIP Switcher Encoder, Switcher Encoder, SW2, EN7
13 ore fa — This guide helps you install and use your KDS-SW2-EN7 for the first time. Go to www.kramerav.com/downloads/KDS-SW2-EN7 to download the latest user manual and ...
KDS-SW2-EN7 Quick Start. P/N: 2 9 0 0 - 3 0 1 5 4 7 QS. Rev: 1. Scan for full manual. KDS-SW2-EN7 Quick Start Guide. This guide helps you install and use ...
12. RS-232 3-pin Terminal Block. Connector. Connect to an RS-232 device to use as a Gateway and bi-directional signal extension (even when no AV signal is ...
File Info : application/pdf, 4 Pages, 708.26KB
DocumentDocumentKDS-SW2-EN7 Quick Start Guide Scan for full manual This guide helps you install and use your KDS-SW2-EN7 for the first time. Go to www.kramerav.com/downloads/KDS-SW2-EN7 to download the latest user manual and check if firmware upgrades are available. Step 1: Check what's in the box KDS-SW2-EN7 2x1 4K AVoIP Switcher Encoder 2 Bracket sets 1 Quick start guide Step 2: Get to know your KDS-SW2-EN7 # Feature 1 HDMI IN Connector 2 USB-C IN Port 3 LCD Display 4 Menu Navigation Button Enter 5 LINK LED 6 NET LED 7 ON LED Function Connect to an HDMI acceptor. Connect to a USB-C source. · When powered by a Kramer 24V power supply (optional), charges sources (that support USB Power Delivery 2.0) up to 60W. Use for device configuration such as input selection, unique channel/AV stream setting and EDID. Press to return to the previous menu. Press to move up to the next configuration parameter. Press to go to the next menu. Press to move down to the next configuration parameter. Press to accept changes. See LED Functionality. See LED Functionality. See LED Functionality. # Feature Function 8 24V/5A DC Connector Connect to the power adapter (purchased separately). 9 RESET Recessed Button Press and hold for 10 seconds to reset the device to its factory default values. All LEDs flash. 10 LAN MEDIA 1G(PoE) RJ-45 Unicast: connect for streaming either directly to a decoder or via LAN. Port Multicast: connect to multiple decoders or connect to one decoder to which multiple decoders are daisy-chained via SERVICE (1G) port. KDS-SW2-EN7 Quick Start P/N: 2 9 0 0 - 3 0 1 5 4 7 QS Rev: 1 # Feature Function 11 LAN SERVICE 1G RJ-45 Port Used optionally for physical separation between AV and command streams to separate LAN for security and reliability purposes. 12 RS-232 3-pin Terminal Block Connect to an RS-232 device to use as a Gateway and bi-directional signal extension (even Connector when no AV signal is extended). 13 AUDIO IN/OUT 5-pin Connect to a balanced analog stereo audio source/acceptor. Terminal Block Connector 14 IR 3.5 Mini Jack Connect to an IR sensor or emitter for bi-directional signal extension (even when no AV signal is extended). Expected voltage for IR receiver - (3.3V). 15 USB Type A Charging Ports Connect to USB devices, for example, to a speakerphone and webcam. (1 and 2) 16 HOST USB Type B Port Connect to a USB host. 17 HDMI OUT Connector Connect to loop the signal. LED Functionality KDS-SW2-EN7 LEDs function as follows: LED Color Definition LINK LED Lights Green NET LED Flashes Green Off Lights green A link is established between KDS-SW2-EN7 and the decoder is transmitting A/V signals. A signal is established, and a problem is detected No IP address is acquired. A valid IP address has been acquired. ON LED Flashes Green very fast (for 60sec) Lights Yellow Lights Red Flashes Red Lights Green Flashes Green Slowly Flashes green fast Flashes Green very fast (for 60sec) Lights Yellow Lights Red A device identification command is sent (Flag me). Device falls back to default IP address. Security is blocking IP access. On fallback address acquiring, device `ON' LED flashes continuously in slow 0.5/10sec cadence When power is on. Device is in standby mode. FW is downloaded in the background. A device identification command is sent (Flag me). Device falls back to default IP address Security is blocking IP access. Post reboot, all LEDs light for 3 seconds then return to their normal LED display mode. Step 3: Mount KDS-SW2-EN7 Install KDS-SW2-EN7 using one of the following methods: · Attach the rubber feet and place the unit on a flat surface. · Fasten a bracket (included) on each side of the unit and attach it to a flat surface (see www.kramerav.com/downloads/KDS-SW2-EN7). · Mount the unit in a rack using the recommended rack adapter (see www.kramerav.com/product/KDS-SW2-EN7). · Ensure that the environment (e.g., maximum ambient temperature & air flow) is compatible for the device. · Avoid uneven mechanical loading. · Appropriate consideration of equipment nameplate ratings should be used for avoiding overloading of the circuits. · Reliable earthing of rack-mounted equipment should be maintained. · Maximum mounting height for the device is 2 meters. Step 4: Connect inputs and outputs Always switch OFF the power on each device before connecting it to your KDS-SW2-EN7 and KDS-DEC7. KDS-SW2-EN7 and KDS-DEC7 can stream 4K video, requiring a gigabit Ethernet switch for high quality performance, since the maximum momentary transfer rate can reach 850Mbps. We recommend using AVoIP Ethernet switches that support: Multicast forwarding or filtering, IGMP Snooping, IGMP Querier, IGMP snooping fast leave and Jumbo frame (8000 bytes or larger). Connecting the audio input/output To a balanced stereo audio source/acceptor: To an unbalanced stereo audio acceptor: To an unbalanced stereo audio source: To achieve specified extension distances, use the recommended Kramer cables available at www.kramerav.com/product/KDS-SW2-EN7. Using third-party cables may cause damage! Step 5: Connect power By-default, the device uses PoE for powering the device. Optionally, you can separately purchase a power adapter to connect to the product and plug into the mains electricity. Safety Instructions (See www.kramerav.com for updated safety information) Caution: · For products with relay terminals and GPIO ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual. · There are no operator serviceable parts inside the unit. Warning: · Use only the power cord that is supplied with the unit. · Disconnect the power and unplug the unit from the wall before installing. Step 6: Operate KDS-SW2-EN7 Allocating the IP Address via LCD screen menu KDS-SW2-EN7 IP default address is 192.168.1.39. By default, DHCP is enabled, and assigns an IP address to the device. If DHCP Server is not available, for example, in case a device is connected directly to the laptop, that device gets the default IP address. If this IP addresses is already in use, the system searches for a random unique IP in the range of 192.168.X.Y. the allocated IP address can be identified using the LCD screen menu. To allocate the IP address via LCD screen Menu: 1. Connect the device to the 24V DC power adapter and connect the adapter to the mains electricity. The ON LED lights green, and the LINK LED flashes (indicating that no streaming activity is detected). 2. Use the Navigation button to view the assigned IP address on the LCD screen: DEV STATUS > LAN1 Status DEV STATUS > LAN2 Status (if the Service port connected as well). Setting Channel Number Each encoder requires a unique channel number, and the connected decoders should be tuned to that encoder channel. You can set the channel number via the LCD screen menu or the embedded web pages. To set the channel number for KDS-SW2-EN7 via LCD screen menu: 1. Connect the device to the 24V DC power adapter and connect the adapter to the mains electricity. The ON LED lights green, and the LINK LED flashes (indicating that no streaming activity is detected). 2. In the LCD screen menu, go to DEV SETTINGS > CH DEFINE. 3. Change channel number using arrow buttons and set a unique channel number. 4. Press Enter to save your selection. To set the channel number via web pages: 1. Connect the KDS-SW2-EN7 Ethernet port to the network and power the device. 2. Access the embedded web pages. 3. In the Main page: For KDS-SW2-EN7: Go to AV Routing page. Select Channel ID and define the channel ID number.