Welcome to Anour | Reintroducing the value of simplicity
Instruction Manual for ANOUR models including: I-Model Cordless, Model Cordless, Cordless
Tel: 4533607070 - Mail: contact@anour.dk - www.anour.dk October 2021 - -- - - WIRING INSTALATION MANUAL - luminary length up to 2,5 meter Check your order first, as you cannot combine multiple solutions.
File Info : application/pdf, 4 Pages, 1.12MB
DocumentDocumentI-MODEL CORDLESS Installation manual Please, read our instructions before installing and using the product. If you have any problems with the electrical installation, contact an electrician. Be sure to turn off the power before you start the installation. In some countries, all electrical installation must be carried out by professional electricians only. For further information, contact the relevant authorities. Our products are for indoor use only. Check on a regular basis that the cord and other parts are not damaged. In this case, the product must not be used. Save these instructions for future use. We use LED as a light source for our products. For replacement of LED contact Anour. The product should not be dismantled as it may get damaged. The product should not come into direct contact with water. Trailing edge dimming is not available for our product. We do not supply power cable from outlet to the power supply. Our products are marked with the symbol of the crossed out wheelie bin. That means that the product should not be disposed of with other household waste. Our products must be recycled in accordance with local environmental regulations for the disposal of waste. In complying with this you will help to minimize any adverse effect on human and environmental health. If you have any questions please contact Anour. contact@anour.dk (2022) 2 1 Positive pole +4 10 Button 6 7 2 Be careful to never cross the steel wires 5 + 3 - Negative pole - 8 9 NEGATIVE POLE 230V 1. Measure distance between the suspension points. See below. TX20 2. Drill holes and fasten the plastic ceiling components. 3. Position the driver box (see diagram below), drill holes and fasten it. DIMENSIONS 5,3 cm 23 cm 54 cm 100 cm 3,3 kg 23 cm 33 cm 84 cm 150 cm 5 kg 33 cm 4. Attach the wires to the nipples and tightly fasten the wires to the lamp. The negative pole is the suspension point closest to the logo. <12° 5. Insert the steel wires in the 2 plastic ceiling components. Assure that the wires are aligned. Be careful to never 6. Insert the + wire in the + terminal and the wire in the - terminal. You can change the position of the poles by 7. Adjust the height of the 8. Connect the power lamp by pressing the wire cable to the (PRI) griper and, cut the excess terminals on the primary wire, as shown. side of the power supply and then, fasten the We recommend to hang screw of the safety cap. the light with a distance of cross the steel wires. repositioning the wire gripers. +/- 60cm above a dinning table. For kitchen table tops, we recommend +/- 70 - 80cm. We do not supply power cable from outlet to power supply. Should be performed DRIVER BOX POSITION OPTIONS: (TOP VIEW DIAGRAM) according to safety regulations. 9. Cut out one input for the primary power cable (3 options shown) in the white plastic lid and then attach the lid to the power supply (magnetic closure). 10. On / Off / Dimming. · Quick tap on the button on the lamp = On/Off. · Hold finger on the button = brighten or dim. · Double tap: for max or min brightness 12. 1. 2. 3. 13. 4. 5. PARTS: (INCLUDED IN THE PACKAGE) 38 cm 48 cm 48 cm 124 cm 200 cm 6,5 kg 38 cm 154 cm 250 cm 204 cm 300 cm 48 cm 8 kg 48 cm 10 kg For sloped installation, the angle of the ceiling inclination must be less than 12 degrees. 11. 10. 14. 9. 8. Suspension point Driver box position options I Model Lamp Wire x1 x4 x4 x2 x2 x2 x1 pair of gloves Ø 4,2 x 55mm Ø 5,5 x 32mm Ø16 x 31mm Ø1,2mm x 8m Ø6 x 20mm Driver box white 340 x 36,5 x 31 mm 6. 7. REQUIRED TOOLS: (NOT INCLUDED) (L x W x H) Hammer Screwdriver Leveling TX20 tool Measuring tool Wire clippers Drill Drill bit Ø5,5 (6) mm - + - + - + - + WIRING INSTALATION MANUAL LUMINARY LENGTH UP TO 2,5 METER Check your order first, as you cannot combine multiple solutions. If you have any problems with the electrical installation, contact an electrician. Be sure to turn off the power before you start the installation. In some countries, all electrical installation must be carried out by professional electricians only. For further information, contact the relevant authorities. Trailing edge dimming is not available. We do not supply power cable from outlet to power supply. 1. DIAGRAM STANDARD WITH TOUCH DIMMER BUTTON ON THE LAMP DALI PRI PUSH DIM 220-240V - + DO NOT USE L N GROUND 2. DIAGRAM DALI - + LED SEC LED DRIVER DALI PRI PUSH DIM 220-240V L N GROUND DALI DALI INPUT DALI SWD LUMINARY LENGHT 2,55 - 3,0 METER 5. DIAGRAM STANDARD WITH TOUCH DIMMER BUTTON ON THE LAMP, 2,55m - 3,0m LUMINARY PRI 220-240V DO NOT USE SEC - + LED LED DRIVER 6. DIAGRAM DALI, 2,55m - 3,0m LUMINARY PRI 220-240V DO NOT USE - + SEC LED DRIVER + + LED - LED LED - DIMMBOX - DALI PRI PUSH DIM 220-240V 3. DIAGRAM PUSH DIM - + LED + SEC LED DRIVER - 4. DIAGRAM 1-10V - + + - INPUT SEC LED DRIVER 1-10 V + LED - LED - SYNC 1-10V - - LED + PRI 220-240V 7. DIAGRAM PUSH DIM, 2,55m - 3,0m LUMINARY DALI PRI PUSH DIM 220-240V L N GROUND N PUSH LINE DO NOT USE - + SEC LED DRIVER + + LED - LED + LED - - DIMMBOX - INPUT DALI SWD L N GROUND + 1-10 V - 8. DIAGRAM 1-10v, 2,55m - 3,0m LUMINARY DO NOT USE - + SEC LED DRIVER PRI 220-240V + - INPUT + LED -- LED DIMMBOX SYNC -1-10V - + LED Tel: +4533607070 - Mail: contact@anour.dk - www.anour.dk October 2022 L N GROUND L N GROUND DALI DALI L N GROUND N PUSH LINE L N GROUND + 1-10 V - I-MODEL CORDLESS DROP CEILING Installation manual OPTION: DROP CEILING INSTALLATION If you wish to receive this installation kit, please mention it when ordering. This is not supplied as standard Please note that this schema won't fit to every type of ceiling installation. Consult an electrician beforehand. Please, read our instructions before installing and using the product. If you have any problems with the electrical installation, contact an electrician. Be sure to turn off the power before you start the installation. In some countries, all electrical installation must be carried out by professional electricians only. For further information, contact the relevant authorities. Our products are for indoor use only. Check on a regular basis that the cord and other parts are not damaged. In this case, the product must not be used. Save these instructions for future use. We use LED as a light source for our products. For replacement of LED contact Anour. The product should not be dismantled as it may get damaged. The product should not come into direct contact with water. Trailing edge dimming is not available for our product. We do not supply power cable from outlet to the power supply. Our products are marked with the symbol of the crossed out wheelie bin. That means that the product should not be disposed of with other household waste. Our products must be recycled in accordance with local environmental regulations for the disposal of waste. In complying with this you will help to minimize any adverse effect on human and environmental health. If you have any questions please contact Anour. contact@anour.dk (2022) Positive pole + 4 meters provided Button PARTS: (INCLUDED IN THE PACKAGE) 10mm 1 1. Wall anchor 2 2. Brass disc + Connector 3. Attachment part 4. Screw 5. Wire griper 3 6. Suspension wire 7. Insulated cable 4 5 6 7 Insert the cable in the connector and tight the screw. total height 37mm x1 x2 x2 x2 pair of gloves Ø4,2 x 60mm Ø5,5 x 32mm Ø14 x 20mm x2 x2 Ø10 x 16mm Ø6 x 20mm x2 x2 x2 Ø35 x 7mm insulated cord steel wire Ø1,2mm x 4m Ø1,2mm x 4m x1 Driver 274 x 30 x 25 mm (L x W x H) REQUIRED TOOLS: (NOT INCLUDED) Hammer Screwdriver TX20 DIMENSIONS Leveling tool Measuring tool Wire clippers Drill Drill bit Ø5,5 (6) mm 23 cm 54 cm 100 cm 3,3 kg 23 cm 33 cm 84 cm 150 cm 5 kg 33 cm 38 cm 48 cm 48 cm 124 cm 200 cm 6,5 kg 38 cm 154 cm 250 cm 204 cm 300 cm 48 cm 8 kg 48 cm 10 kg <12° For sloped installation, the angle of the ceiling inclination must be less than 12 degrees. -Negative pole The driver needs to be accessible at any time for replacement or maintenance. 230V DROP CEILING DROP CEILING Ø5mm hole 10mm 4 meters provided Ø3mm hole DRIVER 230V - LAMP - + - + - + - + WIRING INSTALATION MANUAL LUMINARY LENGTH UP TO 2,5 METER Check your order first, as you cannot combine multiple solutions. If you have any problems with the electrical installation, contact an electrician. Be sure to turn off the power before you start the installation. In some countries, all electrical installation must be carried out by professional electricians only. For further information, contact the relevant authorities. Trailing edge dimming is not available. We do not supply power cable from outlet to power supply. 1. DIAGRAM STANDARD WITH TOUCH DIMMER BUTTON ON THE LAMP DALI PRI PUSH DIM 220-240V - + DO NOT USE L N GROUND 2. DIAGRAM DALI - + LED SEC LED DRIVER DALI PRI PUSH DIM 220-240V L N GROUND DALI DALI INPUT DALI SWD LUMINARY LENGHT 2,55 - 3,0 METER 5. DIAGRAM STANDARD WITH TOUCH DIMMER BUTTON ON THE LAMP, 2,55m - 3,0m LUMINARY PRI 220-240V DO NOT USE SEC - + LED LED DRIVER 6. DIAGRAM DALI, 2,55m - 3,0m LUMINARY PRI 220-240V DO NOT USE - + SEC LED DRIVER + + LED - LED LED - DIMMBOX - DALI PRI PUSH DIM 220-240V 3. DIAGRAM PUSH DIM - + LED + SEC LED DRIVER - 4. DIAGRAM 1-10V - + + - INPUT SEC LED DRIVER 1-10 V + LED - LED - SYNC 1-10V - - LED + PRI 220-240V 7. DIAGRAM PUSH DIM, 2,55m - 3,0m LUMINARY DALI PRI PUSH DIM 220-240V L N GROUND N PUSH LINE DO NOT USE - + SEC LED DRIVER + + LED - LED + LED - - DIMMBOX - INPUT DALI SWD L N GROUND + 1-10 V - 8. DIAGRAM 1-10v, 2,55m - 3,0m LUMINARY DO NOT USE - + SEC LED DRIVER PRI 220-240V + - INPUT + LED -- LED DIMMBOX SYNC -1-10V - + LED Tel: +4533607070 - Mail: contact@anour.dk - www.anour.dk October 2022 L N GROUND L N GROUND DALI DALI L N GROUND N PUSH LINE L N GROUND + 1-10 V -