Instruction Manual for ALPINE models including: PSS-TSLA-213 Speaker System, PSS-TSLA-213, Speaker System
Alpine PSS-TSLA-213 11-speaker sound system upgrade for 2018-21 Tesla Model 3 with Factory Base Audio at Crutchfield
Alpine PSS-TSLA-223P 13-Speaker Sound System Upgrade for the 2022 Tesl - Gibbys Electronic Supermarket
Alpine PSS-TSLA-213 11-Speaker Sound System Upgrade for the 2018-21 Te - Gibbys Electronic Supermarket
File Info : application/pdf, 12 Pages, 16.95MB
DocumentDocumentImportant Notice
PSS-TSLA
Tesla Model 3 & Y
20240220v2
1/12
WARNING: This aftermarket plug-and-play audio system for Tesla vehicles ("Product") is intended for installation by qualified professionals with experience in automotive electrical systems. Improper installation can result in serious damage to your vehicle, electrical system, and personal injury or death. By purchasing and/or installing this Product, you acknowledge and agree to the following:
Installation at your own risk: You assume all responsibility and risk associated with the installation of this Product. Neither Alps Alpine North America, Inc. nor its affiliates are responsible for any damage or injury caused by improper installation.
The installation of this product requires specialized skills and experience. We recommend that you have the product installed by an Alpine authorized dealer
Potential for electrical damage: Improper installation can cause electrical damage to your Tesla vehicle, including, but not limited to, blown fuses, shorts, fires, and damage to sensitive electronic components and batteries.
No warranty for improper installation: This Product's warranty is expressly limited to manufacturing defects and does not cover any damage caused by improper installation.
ASSUMPTION OF RISK: YOU ACKNOWLEDGE AND AGREE THAT YOU ARE KNOWINGLY ASSUMING THE RISK OF DAMAGE TO YOUR TESLA VEHICLE AND/OR PERSONAL INJURY OR DEATH BY INSTALLING THIS PRODUCT YOURSELF AND THAT INSTALLING THIS PRODUCT MAY AFFECT OR RESULT IN TERMINATION OF YOUR LIMITED WARRANTY WITH TESLA.
LIMITATION OF LIABILITY: TO THE FULLEST EXTENT PERMITTED BY LAW, ALPS ALPINE NORTH AMERICA, INC. AND ITS AFFILIATES SHALL NOT BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, OR PUNITIVE DAMAGES ARISING OUT OF OR RELATED TO THE INSTALLATION OR USE OF THIS PRODUCT, INCLUDING, BUT NOT LIMITED TO, DAMAGE TO YOUR TESLA VEHICLE, PERSONAL INJURY, PROPERTY DAMAGE, OR RENDERING YOUR LIMITED WARRANTY INEFFECTIVE.
We strongly recommend consulting your Tesla owner's manual or qualified professional for specific installation instructions. We recommend reviewing all online resources and tutorials available for your specific Tesla model before attempting installation. If you are unsure about any aspect of the installation process, please consult a qualified professional.
PSS-TSLA
Tesla Model 3 & Y
20240220v2
2/12
Tesla Model 3/Y Power UP & Down Procedure
WARNING: Before beginning install on your tesla follow the below procedure. IMPORTANT: Re-install ALL Factory Plugs To Their Original Location, FAILURE TO DO SO CAN CREATE COMPUTER FAULTS.
Battery State should be near 100% charged. ALL WINDOWS ROLLED DOWN Frunk & Trunk is OPEN
Tesla Model 3/Y Power Down Procedure
1) Turn off the Screen in Settings Following Step (A,B,C)
A) Enter the Controls Menu in bottom Left Corner B) Tap Safety & Security Menu on the Left-Hand Menu C) Press the Power OFF Button, and Confirm OFF
2) Access the Frunk and disconnect the low voltage battery (-) Cable. 3) Remove the Rear Bench Seat Cushion by unlatching 2 lock mechanisms at
the bottom edge of the seat. 4) Un-Plug the the high voltage contactor under the Rear Seat
Tesla Model 3/Y Power Up Procedure
1) Under the Rear Bench Seat cushion plug- in and latch the high voltage battery contactor pictured above.
2) Access the Frunk and re-connect the low voltage battery (-) Cable. 3) Power up the vehicle pressing the brake pedal.
PSS-TSLA
Tesla Model 3
20240220v2
3/12
Installation Instructions (Integration Harness)
1 Remove 2 factory trim Panels from the passenger foot
well. The under dashboard trim panel and the kick panel cover both located under the dashboard in the passenger foot well.
2 Inside of the passenger footwell locate the signal
distribution box. Disconnect the 2 bottom male connectors and replace with plugs (A + B) from the Alpine Tesla Harness. Transfer the disconnected connectors into the open ends of the Alpine Harness.
A B
3 Route the harness cable from inside the dash down to
the passenger kick panel and locate the matching plug, disconnect the connector and transfer it to the harness. (Plug C)
4 Remove the passenger side baseboard lower door trim
and locate the connector just before the base of the
B-pillar. Transfer the connections to (Plug D)
D
C
PSS-TSLA
Tesla Model 3
20240220v2
4/12
Installation Instructions (Integration Harness)
5 Route the harness under the passenger trim up to the
back of the vehicle. Leave a proper amount of slack so that your plugs can reach the final amplifier mounting location.
6 (Plugs E & F) are routed for rear deck speaker equipped
vehicles. (Some Model 3 Base RWD made 2021+ do not have rear deck speakers)
E F
7 Route cable G behind the trunk lining trim, (Plug G)
connects to the subwoofer enclosure located behind the
rear passenger tire well.
8 (Plug H & I) High level input and DSP output connect to
the Alpine Amp PXE-X121-12EV
H
I G
G
PSS-TSLA
Tesla Model 3 & Y
20240220v2
5/12
Installation Instruction (Power Harness)
FULLY POWER DOWN YOUR TESLA AND DISCONNECT BATTERY BEFORE CONTINUING. SEE POWER DOWN PROCEDURE
IMPORTANT: For Optimal Sound Quality Sound Dampening Is Highly Recommended for Tesla Applications
IMPORTANT: Re-install ALL Factory Plugs To Their Original Location, FAILURE TO DO SO CAN CREATE COMPUTER FAULTS.
1 Route 12V Power Harness (Plug J) from the trunk to the
rear bench seat along the passenger side of the vehicle.
2 Locate the low voltage 12V battery posts in the rear seat
passenger compartment (Under the seat) Use a socket to remove the battery hardware.
3 Connect the harness Positive and Negative lug to the low
voltage battery posts under the rear seat & re-tighten hardware.
3 Route the remote trigger 18awg primary wire (M) to the
rear of the center console. Extra Length is OK
J
M
J
-
+
M
PSS-TSLA
Tesla Model 3 & Y
20240220v2
6/12
Installation Instruction (Power Harness)
FULLY POWER DOWN YOUR TESLA AND DISCONNECT BATTERY BEFORE CONTINUING. SEE POWER DOWN PROCEDURE
IMPORTANT: For Optimal Sound Quality Sound Dampening Is Highly Recommended for Tesla Applications
IMPORTANT: Re-install ALL Factory Plugs To Their Original Location, FAILURE TO DO SO CAN CREATE COMPUTER FAULTS.
1 Use a panel removal tool to remove the lower rear cover
of the center console, once removed this should reveal two large plugs.
2 Locate and unpack the CP1-S CANPRO and CP1-TSL1
K
L
3 Connect Harness "K" black plastic molex end with
corresponding plug of CANPRO CP1-S Module "L" . Set dipswitch 2 to ON position
4 Disconnect factory connectors and replace the white
plastic plugs from CP1-TSL1 "K" into the rear center console Plugs. Trim the excess length wire from "M" and crimp together with Output #1 from CP1-S "L"
K
5 When finished tuck all excess wiring and CANPRO
module into the rear center console compartment and re-install the lower cover using factory clips.
M L
Crimp Connector
J
K L
M
Crimp Connector
PSS-TSLA
Tesla Model 3 & Y
20240220v2
7/12
Dashboard Speaker Installation (EV-40MR-T)
FULLY POWER DOWN YOUR TESLA AND DISCONNECT BATTERY BEFORE CONTINUING. SEE POWER DOWN PROCEDURE
IMPORTANT: For Optimal Sound Quality Sound Dampening Is Highly Recommended for Tesla Applications
IMPORTANT: Re-install ALL Factory Plugs To Their Original Location, FAILURE TO DO SO CAN CREATE COMPUTER FAULTS.
1 Using a panel removal tool.
Remove dash side cover "A" followed by pillar cover "B" at both sides of vehicle. Weather gasket can be peeled back slightly for easier removal.
2 Use a Panel Removal Tool around the edge of the
dashboard speaker cover panel to release the factory clips. Release the panel and pull upwards to detatch and expose the center stage speakers.
B
A
3 Remove (3) T20 Torx bolts securing each factory speaker
Remove (2) T20 bolts securing the factory tweeter Use T20 Torx. A Shallow Ratcheting Torx Bit is required.
4 Connect the Y-Harness between the center mid and
tweeter & Plug all speakers into the factory connectors
5 Secure all Alpine speakers to the dash by Re-installing all
remaining factory T20 Torx. After speakers are mounted Install the dashboard speaker cover panel by applying uniform pressure to engage the factory clips.
6 Re-install dash side cover "A" followed by pillar cover "B"
at both sides of vehicle.
PSS-TSLA
Tesla Model 3 & Y
20240220v2
8/12
Front Door Speaker Installation (EV-65CF-T)
FULLY POWER DOWN YOUR TESLA AND DISCONNECT BATTERY BEFORE CONTINUING. SEE POWER DOWN PROCEDURE
IMPORTANT: For Optimal Sound Quality Sound Dampening Is Highly Recommended for Tesla Applications
IMPORTANT: Re-install ALL Factory Plugs To Their Original Location, FAILURE TO DO SO CAN CREATE COMPUTER FAULTS.
1 Remove the Front Door Panels
Pry the Red Reflector Clip Off Using Slim Panel Remover Use a T30 Screw Driver Remove (3) Screws in Each Panel (2) Screws are located under the door grip handle (1) Screw is located behind the red reflector
2 Use a Panel Removal Tool around the edge of the panel
to release the factory clips. Release the panel and pull upwards to detatch, un-plug the factory panel connections including the green speaker plug
3 Remove 4 bolts securing each factory speaker adapter.
Use 8mm Socket or T25 Torx (Varies depending on year) The factory Adapter should then unclip easily.
4 Install the new Alpine Speaker & Adapter to the door
panel using the factory screws. Plug in green speaker adapter plug
5 Plug in all remaining factory door connectors. Mount
and re-install each factory door panel using (3) T30 Torx. Apply Pressure around the door panel to engage the factory clips. Re-install the Red Reflector Clips
PSS-TSLA
Tesla Model 3&Y
20240220v2
9/12
Front Door Tweeter Installation (EV-65CF-T)
FULLY POWER DOWN YOUR TESLA AND DISCONNECT BATTERY BEFORE CONTINUING. SEE POWER DOWN PROCEDURE IMPORTANT: For Optimal Sound Quality Sound Dampening Is Highly Recommended for Tesla Applications IMPORTANT: Re-install ALL Factory Plugs To Their Original Location, FAILURE TO DO SO CAN CREATE COMPUTER FAULTS.
1 Using a panel removal tool remove the Front Tweeter
Housing Panel Use Light Upward Pressure and Pry to Release 2 Clips.
2 With the Tweeter Housing un-clipped from the door
unplug the factory speaker connector. If the plug is difficult use a small precision flat tool to release the plug connection
3 Unclip the Factory Tweeter from the Housing by gently
twisting and pulling.
4 Install the new Alpine Tweeter by clipping into place.
5 Plug in the original factory connector to the new alpine
tweeter and pop the housing into place using downward pressure along the factory clips. Make sure it securely latches into place.
PSS-TSLA
Tesla Model Y
20240220v2
10/12
Rear Door Speaker Installation (EV-40M-T)
FULLY POWER DOWN YOUR TESLA AND DISCONNECT BATTERY BEFORE CONTINUING. SEE POWER DOWN PROCEDURE
IMPORTANT: For Optimal Sound Quality Sound Dampening Is Highly Recommended for Tesla Applications
IMPORTANT: Re-install ALL Factory Plugs To Their Original Location, FAILURE TO DO SO CAN CREATE COMPUTER FAULTS.
1 Remove the Rear Door Panels
Use a T30 Screw Driver Remove (2) Screws in Each Panel (2) Screws are located under the door grip handle
2 Use a Panel Removal Tool around the edge of the panel
to release the factory clips. Release the panel and pull upwards to detatch, un-plug the factory panel connections.
3 Using a Drill Bit, Drill out 3 Plastic Rivets on each Factory
Door Speaker. Use Care to not over-drill the screw boss
4 Using hand screw driver nstall the new Alpine Speaker to
the door panel using the (6) supplied phillips tapping screws & Plug in the speaker connector
Drill out the Rivet
5 Plug in all remaining factory door connectors. Mount
and re-install each factory door panel using (2) T30 Torx. Apply Pressure around the door panel to engage the factory clips.
Replace 3 Rivet with Tapping Screw
PSS-TSLA
Tesla Model 3P
20240220v2
11/12
Rear Deck Speaker Installation (EV-40M-T)
FULLY POWER DOWN YOUR TESLA AND DISCONNECT BATTERY BEFORE CONTINUING. SEE POWER DOWN PROCEDURE
IMPORTANT: For Optimal Sound Quality Sound Dampening Is Highly Recommended for Tesla Applications
IMPORTANT: Re-install ALL Factory Plugs To Their Original Location, FAILURE TO DO SO CAN CREATE COMPUTER FAULTS.
1 Remove the factory deck and Rear Deck Speaker Grille
Covers
2 Un-install the factory rear deck speakers
3 Install the new 4" Midrange speaker into the factory
location. Use Plug (E) AND (F) to connect the speaker leads.
E F
4 Re-install the factory grille covers and deck into the
vehicle.
PSS-TSLA
Tesla Model 3 / 3P
20240220v2
12/12
Model 3 Subwoofer Installation (EV-100SW3-T)
FULLY POWER DOWN YOUR TESLA AND DISCONNECT BATTERY BEFORE CONTINUING. SEE POWER DOWN PROCEDURE
IMPORTANT: For Optimal Sound Quality Sound Dampening Is Highly Recommended for Tesla Applications
IMPORTANT: Re-install ALL Factory Plugs To Their Original Location, FAILURE TO DO SO CAN CREATE COMPUTER FAULTS.
1 To access the subwoofer compartment remove the lower
plastic trim panel "A" and the upper plastic trim panel "B" Use a Panel Removal tool to release the clips. After removed do not lose the factory clips.
2 Uninstall the factory subwoofer from vehicle. Peel back
the carpet "C" to expose the factory subwoofer. Unscrew the 2 factory bolts, if equipped with Premium audio
B
B
C
A
3 Mount the new subwoofer box and install the factory
hardware to the two mounting positions
4 Installed the Alpine supplied nut to the third factory bolt
location.
5 Re-install the factory amplifier and bolts if premium
equipped.
6 Re-connect the factory subwoofer plug, place the carpet
into position and re-install the upper and lower plastic trim panels.
Adobe PDF library 17.00