Zebra ZD510, ZD511 Regulatory Guide

Zebra ZD510, ZD511 Regulatory Guide

Printed in China

Zebra Technologies | 3 Overlook Point | Lincolnshire, IL 60069 USA

Website: www.zebra.com

©2018 ZIH Corp and/or its affiliates. All rights reserved. Zebra and the stylized Zebra Head are trademarks of ZIH Corp., registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners.

Worldwide Regulatory Information

All Zebra devices are designed to be compliant with the rules and regulations in locations they are sold and will be labeled as required. For more information about Zebra's compliance with national and international mandates, go to: www.zebra.com/compliance

For the latest version of this guide, go to: www.zebra.com/support

Any changes or modifications to Zebra equipment, not expressly approved by Zebra, could void the user's authority to operate the equipment.

End User License Agreement

For the complete End User License Agreement, go to www.zebra.com/eula

Warranty

For the complete hardware product warranty statement, go to www.zebra.com/warranty

Brazil - Aviso da Anatel

Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário.

“Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resolução 242/2000, e atende aos requisitos técnicos aplicados”

Para maiores informações, consulte o site da ANATEL www.anatel.gov.br

This equipment's operation is of a secondary character; that is, it doesn't have the right to protection against damaging interference, even from stations of the same type, nor can it cause interference to systems with a primary operating character.

Este produto utiliza internamente o modulo de ZBRBLE numero de homologação pela ANATEL 0581-16-5041 e o modulo WYSBHVGXG numero de homologação pela ANATEL 0581-16-1530

Canada

DOC Compliance

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

This Class B digital apparatus complies with Canadian ICES-003.

Innovation, Science and Economic Development Canada (ISED) Warning

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1) This device may not cause interference., 2) This device must accept any interference, including interference that may cause undesired operation of the device.

China

Hazardous Substances

本表格依据SJ/T 11364的规定编制

Toxic/Hazardous Substances or Elements
Part Name Lead
(PB)
Mercury
(Hg)
Cadmium
(CD)
Hexavalent Chromium
(CR6+)
Polybrominated Biphenyls
(PBB)
Polybrominated Diphenyl Ethers
(PBDE)
Enclosure X O O O O O
Electronics X O O O O O
Drivetrain X O O O O O
Fasteners X O O O O O
Cutters X O O O O O
Print Heads X O O O O O
External Power Supply X O O O O O
802.11 Radio Card X O O O O O

X indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in GB/T 26572.

O indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in GB/T 26572.

European Union (EU)

Hereby, Zebra Technologies Corporation declares that the radio equipment type WLAN or Bluetooth is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.zebra.com/compliance

(Note: Declarations in other EU languages are present in the original document but are omitted here for conciseness, focusing on the primary language.)

Antenna and WLAN/Bluetooth Specifications

Antenna Information:

  • Type = Patch
  • Gain = 3.66dBi @ 2.4GHz
  • Gain = 3.19dBi @ 5GHz
  • Type = Chip
  • Gain = 1dBi @ 2.4 GHz

WLAN Specifications:

802.11 b

  • 2.4 GHz
  • DSSS (DBPSK, DQPSK and CCK)
  • RF power 17.77 dBm (EIRP)

802.11 g

  • 2.4 GHz
  • OFDM (16-QAM and 64-QAM with BPSK and QPSK)
  • RF power 18.61 dBm (EIRP)

802.11 n

  • 2.4 GHz
  • OFDM (16-QAM and 64-QAM with BPSK and QPSK)
  • RF power 18.62 dBm (EIRP)

802.11 a/n

  • 5.15-5.25 GHz, 5.25-5.35 GHz, 5.47-5.725 GHz
  • OFDM (16-QAM and 64-QAM with BPSK and QPSK)
  • RF power 17.89 dBm (EIRP)

802.11 ac

  • 5.15-5.25 GHz, 5.25-5.35 GHz, 5.47-5.725 GHz
  • OFDM (16-QAM and 64-QAM with BPSK and QPSK)
  • RF power 13.39 dBm (EIRP)

Bluetooth Specifications:

Bluetooth 4.1 + Low Energy

  • 2.4GHz
  • FHSS(BDR/EDR), GFSK(Bluetooth Low Energy)
  • RF power 9.22 dBm (EIRP)

Bluetooth 4.1 + Low Energy (LE Only)

  • 2.4GHz
  • FHSS(BDR/EDR), GFSK(Bluetooth Low Energy)
  • RF power -0.85 dBm (EIRP)

Korea

The equipment is for home use (Class B) and has acquired electromagnetic conformity registration, so it can be used not only in residential area but other areas as well.

This radio device is not allowed to be used for human safety since it has possibility of radio interference during operation.

Mexico

Este equipo ha sido diseñado para operar con las antenas que enseguida se enlistan y para una ganancia máxima de antena de [3.66] dBi. El uso con este equipo de antenas no incluidas en esta lista o que tengan una ganancia mayor que [3.66] dBi quedan prohibidas. La impedancia requerida de la antena es de [50] ohms.

Antenna Information:

  • Type = Patch
  • Gain = 3.66dBi @ 2.4GHz
  • Gain = 3.19 dBi @ 5GHz
  • Impedance = 50 ohms
  • Type = Chip
  • Gain = 1dBi @ 2.4GHz

United States of America

FCC Compliance

This device complies with Part 15 rules. Operation is subject to the following two conditions:

  • This device may not cause harmful interference, and
  • This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for Class B Digital Devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the product manuals, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, the user is encouraged to do one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced RF service technician for help.

IMPORTANT

  1. The radio must be installed with a minimum 20 cm separation between the user and the antenna.
  2. The radio must not be co-located or used in simultaneous transmitting condition with another radio.
  3. The host system shall have a label to indicate that the system contains a certified module.
  4. An example is "Contains FCC ID : XXXXX-XXXXXXXX, IC ID: XXXXX-XXXXXXXX".
  5. The radio is for indoor use only in the 5150-5250 GHz frequency range.

The user is cautioned that any changes or modifications not expressly approved by Zebra Technologies could void the user's authority to operate the equipment. To ensure compliance, this printer must be used with fully shielded communication cables.

Taiwan

General Equipment (Low Power Radio Frequency Device Management Regulations Article 12, 14)

經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率,加大功率或變更原設計之特性及功能。

低功率射頻電機之使用不得影響飛航安全及干擾合法通信:經發現有干擾現象時,應立即停用,并改善至無干擾時方得繼續使用。

前項合法通信,指依電信法規定作業之無線電通信低功率射頻電機需忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

避免電波干擾,本器材禁止於室外使用5.25-5.35秭赫頻帶.

低功率射頻電機管理辦法

第十二條

經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。

第十四條

低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。

前項合法通信,指依電信法規定作業之無線電通信。

低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

避免電波干擾,本器材禁止於室外使用5.25-5.35秭赫頻帶。

限用物質含有情況標示聲明書 (Statement of Hazardous Substance Content)

Equipment name: Printer
Model (Type): ZD510, ZD511
Unit Lead
(PB)
Mercury
(Hg)
Cadmium
(CD)
Hexavalent Chromium
(CR6+)
Polybrominated Biphenyls
(PBB)
Polybrominated Diphenyl Ethers
(PBDE)
Enclosure - O O O O O
PCBA - O O O O O
Motor - O O O O O
Print Heads - O O O O O
Accessory - O O O O O

Note 1: "Exceeding 0.1 wt%" and "exceeding 0.01 wt%" indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition.

Note 2: "O" indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.

Note 3: The "-" indicates that the restricted substance corresponds to the exemption.

公司資訊 (Company Information): 台灣斑馬科技股份有限公司 / 台北市信義區松高路9號13樓

Waste Electrical and Electronic Equipment (WEEE)

Do not dispose of this product in unsorted municipal waste. This product is recyclable, and should be recycled according to your local standards. For more information, please see our website at: www.zebra.com/environment

(Note: WEEE information is provided in multiple languages in the original document. The English version is presented here.)

Models: ZD510 ZD511, ZD510 ZD511 Wristband Printing Solution, Wristband Printing Solution, Printing Solution, Solution

File Info : application/pdf, 10 Pages, 1.89MB

zd510-zd511-rg-ww

References

Adobe InDesign CC 13.0 (Windows) Adobe PDF Library 15.0

Related Documents

Preview MC9401 法規指南
Zebra MC9401 的綜合指南,涵蓋法規遵循、安全資訊、射頻暴露、有害物質和地區認證,確保安全合規操作。
Preview Zebra AltiZ Regulatory Guide
Comprehensive regulatory information, safety precautions, laser safety details, and compliance notices for the Zebra AltiZ device. Includes model specifications, warnings, and international regulatory standards.
Preview Zebra 3PTY-RFID-TC7X Regulatory Guide - Compliance and Safety Information
Comprehensive regulatory guide for the Zebra 3PTY-RFID-TC7X device, detailing RF exposure compliance, safety precautions, CE, FCC, ISED, WEEE, and regional regulatory statements. Includes warranty and support information.
Preview WT6300 Regulatory Guide - Zebra Technologies
This guide provides essential regulatory information for the Zebra WT6300 wearable mobile computer, including safety recommendations, RF exposure guidelines, and compliance statements for various regions.
Preview CS6080 Accessory Regulatory Guide
Comprehensive regulatory and safety information for the Zebra CS6080 accessory, covering compliance, RF exposure, battery safety, and regional certifications including FCC, CE, EAC, and WEEE.
Preview Zebra KC5 Series Regulatory Guide
Regulatory information, safety guidelines, and compliance details for Zebra KC5 Series devices including KC50A15, KC50E15, KC50A22, and KC50E22. Covers RF exposure, power supply, CE, WEEE, FCC, ISED, and RoHS compliance.
Preview Zebra ET6x Smart Card/CAC Reader Regulatory Guide
Comprehensive regulatory information, compliance declarations, and support resources for the Zebra ET6x Smart Card/CAC Reader (Model: XBK-ET6X-SMCARD). Covers FCC, EU, UK, and Canadian regulations, WEEE directives, warranty, service, software, and patent information.
Preview Zebra WS50/WR50 Regulatory Guide
Comprehensive regulatory information, safety guidelines, and compliance declarations for Zebra WS50 and WR50 devices, covering RF exposure, battery safety, and regional certifications.