Dry Contact controlled Retrofit-Motor for Gate Valves

Product Description

The motor drive designed for angle seat valves, specifically KFR valves, offers a solution for seamlessly retrofitting existing shut-off valves into remotely controlled intelligent devices. This process is achieved without the need to interrupt water supply or cut into the water pipe. The 12V-powered motor is not only water-resistant but also resistant to dirt, ensuring durability up to the power supply. Versatility is achieved through various adapter rings and a sophisticated connection system, allowing the motor to be compatible with modern angle seat valves featuring raising or non-raising stems, ranging from DN15 to DN32.

Incorporating an additional water sensor directly connected to the device enhances functionality, enabling the motor to serve as a leak protection system without the need for further configuration or wireless connectivity. The servo motor's waterproof design makes it suitable for deployment in damp, dirty, and outdoor environments. In its open state, the motor autonomously conducts valve training weekly, involving a closing/opening action by 1/8 turn to remove dirt and scale. The device is controlled either through the local button or via a dry wire switch input of the existing smart home system (Shelly, Z-Wave, Smartthings, Bosch, Homematic, ...) or your alarm system.

The product features a compact, weather-resistant motor unit designed to retrofit existing gate valves. It attaches to the valve stem and is powered by a 12V supply. The motor is designed for outdoor use and can withstand damp and dirty environments. It includes an integrated water sensor for leak protection.

Installation of the motor

Please refer to the manual of the motor KFRLWE01 for details on installation on mounting.

Connecting to Dry Outputs

Connect the audio jack of the wire to the output on the end of the power cable. Connect the two blank ends to the output of your smart home or alarm system. Short-cutting the blank ends will close the valve; a non-short-cut will open the valve.

Manual Operation of the Motor

The device has a single button with a built-in tricolor LED. To switch the valve, you can click the button or hold it down for a few seconds. The device is designed for outdoor use and must prevent malfunctions due to water droplets on the button. Therefore, please press the button firmly (not too shyly), even if you only click briefly, so that the touchless button recognizes your finger.

LEDs

The device has a tricolor LED with the following meanings:

• Green slow blinking: Valve is open (can be turned off via parameter 6)
• Red slow blinking: Valve is closed (can be turned off via parameter 6)
• Red/Green blinking: Motor is moving
• Red triple blinking: Motor is blocked

Scope of Delivery

• Motor with power cable (150 cm) to waterproof coupling
• 4 * adapter rings to connect to the valve housing
• 3 different connectors for the stem
• One small Distancering and the Splitring for EWE Valve Design
• Holder plus 2 wrist bands
• Main sleeve plus internal coupler
• Two Distance rings
• External wired Flood Sensor (ALIXXX01)
• External Power Supply with 150 cm cable to waterproof coupling
• Spare Hand Wheel
• Users Manual

Support and Contact

Should you encounter any problem, please give us the opportunity to address it before returning this product. Please check our website www.aqua-scope.com and particularly the support section for answers and help. You can also send a message to info@aqua-scope.com.

While the information in this manual has been compiled with great care, it may not be deemed an assurance of product characteristics. Aqua-Scope shall be liable only to the degree specified in the terms of sale and delivery. The reproduction and distribution of the documentation and software supplied with this product and the use of its contents is subject to written authorization from Aqua-Scope. We reserve the right to make any alterations that arise as the result of technical development.

• Phone: +372 (0) 6248002
• eMail: info@aqua-scope.com
• Web: www.aqua-scope.com

Declaration of Conformity

[CE Mark]

Aqua-Scope Technology OÜ, Sakala 7-2, 10141 Tallinn, Republic of Estonia, declares that this radio emitting device works on the following frequencies:

English: Hereby, Aqua-Scope Technology OÜ declares that the radio equipment type KFRDRY01 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.aqua-scope.com/ce

Disposal Guidelines

Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging health and well-being.