Home - ROBERTS®One moment, please...
Owner's Manual for ROBERTS models including: 6399 Firm Set Transitional Pressure Sensitive, 6399, Firm Set Transitional Pressure Sensitive, Transitional Pressure Sensitive, Pressure Sensitive
vor 21 Stunden — DESCRIPTION. ROBERTS 6399 is a very aggressive, high-tack transitional adhesive that installs like a pressure sensitive adhesive but firms as it cures to ...
ROBERTS - 6399 FIRM SET TRANSITIONAL PRESSURE SENSITIVE ADHESIVE – East Bay Supply Co.
File Info : application/pdf, 2 Pages, 1.03MB
DocumentDocument6399 FIRM SET TRANSITIONAL PRESSURE SENSITIVE Powered by Microban® for superior mold and mildew protection. 1. DESCRIPTION ROBERTS® 6399 is a very aggressive, high-tack transitional adhesive that installs like a pressure sensitive adhesive but firms as it cures to form a permanent bond. ROBERTS 6399 can be used for wet-set or pressure sensitive installations making it suitable for different installation needs across a wide array of resilient floor types and carpet tiles. ROBERTS 6399 offers excellent plasticizer, pH and moisture resistance to withstand extreme environmental conditions. With superior shear strength, ROBERTS 6399 will perform under heavy rolling loads and in all traffic conditions. Features and Benefits · Compatible with a wide range of resilient and carpet tiles · Flexible installation methods Wet Set and Pressure Sensitive · Maximum moisture tolerance of 99% RH / 12lb MVER · Superior shear strength · Ideal for environments with heavy traffic or rolling loads · Durability with reduced floor movement · Easy to use and easy to clean · Apply with a trowel or roller · Spreads opaque white and dries clear · Includes green tracers · Powered by Microban® for superior mold and mildew protection · FloorScore* and CRI Certified · LEED v4 contributing: CDPH v1.2 Approved Flooring Types Recommended Trowel and Coverage Rate* 1/16" x 1/16" x 1/16" (1.5 mm x 1.5 mm x 1.5 mm) SQ Notch Flooring (porous substrate): LVP, LVT, VCT, vinyl sheet flooring, rubber sports flooring, natural cork, rubber underlayment and carpet tile Coverage: 125-185 ft2/per gallon (11.6-17.1 m2/per 3.78 L) 1/16" x 1/32" x 1/32" (1.5 mm x .79 mm x .79 mm) U Notch Flooring (non-porous substrate): LVP, LVT, and cork underlayment Coverage: 185-260 ft2/per gallon (17.1-24.1 m2/per 3.78 L) Short Nap Roller (3/8") (9.5 mm) Flooring (non-porous substrate): Non-Porous Flooring Type: LVP, LVT, VCT, carpet tile and cork underlayment Coverage: Up to 250-350 ft2/per gallon (23.2-32.5 m2/per 3.78 L) * NOTE: The trowel notches referenced are those typically recommended for the type of flooring being installed, and are referenced as a guide. Coverage rates will vary depending on trowel type, substrate and installation conditions. Consult flooring manufacturer for their specific trowel recommendations. LVP (Luxury Vinyl Planks) LVT (Luxury Vinyl Tile) VCT (Vinyl Composition Tile) Vinyl-backed carpet tiles Vinyl sheet goods Other Approved Flooring Types: rubber (tile and sheet), stair treads rubber & vinyl), carpet cushion to substrate, cork-backed hard surface, cork flooring, cork underlayment Approved Substrates Concrete APA-rated plywood Terrazzo VCT (properly prepared) Radiant-heated subfloors (surface temperature < 85°F Sheet vinyl (properly prepared) excluding self stick Association-approved particle board Other Approved Substrates: Cork underlayment, OSB (oriented strand board), Ceramic tile (properly prepared), Cement backerboard(primed), Gypsum(primed) 99% RH UP TO 12 LBS. M V E R 12 For floorings and backings not listed, contact Technical Services at (706) 277-5294. PRESSURE SENSITIVE MOISTURE TRANSITIONAL RESISTANCE SHELF LIFE 2 YEARS LIFETIME WARRANTY * *Based on installation by an industry certified installer Roberts Consolidated Industries, Inc. · robertsconsolidated.com Roberts Company Canada, Ltd. · robertsconsolidated.com/ca 6399 2. TECHNICAL DATA Product Type: Acrylic Polymer Blend Color: Off white with green tracers Odor: Very mild Permanent (Wet-Set) Method Open Time: Up to 20 minutes Working Time: Up to 40 minutes Releasable (Full-Tack) Method Tack Time: Up to 60 minutes Working Time: 12 hours Setup time will vary slightly based on trowel notch, temperature, humidity, moisture and porosity of substrate. Curing Time: 24 -48 hours Traffic: Residential: 0 min (PSA) 12 hours (semi-wet) Commercial: 4 hours Rolling Loads: 24 hours pH: Must not exceed 12 Shelf Life: 2 years from date of manufacture when stored in the original unopened container in a controlled environment. Does not require thinning Storage: While this product is freeze-thaw stable, it is necessary to protect it from freezing. Freeze/thaw stable to 20°F (-6.7°C). VOC: <1 g/L 3. INSTRUCTIONS Limitations · For interior installations only · Not intended for use as a moisture mitigation system, see flooring manufacturer for any RH limitations for their respected products. Do not install in areas with known hydrostatic moisture problems or pH imbalances (pH tolerance 6-12) Preparation Concrete substrate must be dry (within tested moisture tolerance of flooring and adhesive product). Subfloors most be clean, structurally sound and within flat and level tolerance of manufacturer. All substrates must be free of substances such as paints, oils, epoxies, old adhesive residues, etc. that might inhibit the bond of the adhesive or the performance of the flooring or its installation. All substrate cracks, chips, holes, joints or high spots must be adequately repaired. Patching compounds must be suitable for the use application, cement-based and polymer-modified, and applied according to the manufacturer's instructions. Installation Maintain a consistent temperature and ambient relative humidity before, during and after installation (between 65-85°F and 30-50% ambient RH). Follow all industry standards and flooring manufacturer's recommendations for floor flatness, acclimation and application of flooring materials. Spread adhesive uniformly onto the substrate using a trowel (see trowel panel for recommendations). Adhesive trowel ridges should be well defined, consistent and achieve full coverage of the substrate. Observe appropriate open time. When installing over a porous substrate: place flooring into semi-wet adhesive for a permanent bond or allow adhesive to dry and become tacky to the touch for a releasable bond. When installing over non-porous substrate: always allow adhesive to completely dry and become tacky before placing flooring. Once adhesive field has reached appropriate tack, install the floor covering into the adhesive field. Roll the floor covering with a weighted roller per manufacturer's specific guidelines. Post installation: Restrict moving of heavy objects for 24 hours. Clean-up Fresh adhesive warm, soapy water on a clean cloth. Dried adhesive use mineral spirits sparingly with a clean, white cotton cloth. DO NOT POUR DIRECTLY ONTO FLOORING. 4. AVAILABILITY USA 4 G Plastic Pail 1 G Plastic Pail 6399-4 6399-1 CANADA 56.78 L Plastic Pail 6399RB015 3.78 L Plastic Pail 6399RB004 075378639947 075378639916 075378063995 075378639916 5. WARRANTY Roberts Consolidated Inc. offers a limited-product warranty on this product when installed in accordance with the printed specifications. LIMITED WARRANTY: 10-Year limited bond warranty provided the product was properly applied within its applicable shelf life and in accordance with: (a) ROBERTS Product Data Sheet specifications and (b) governmental regulations, codes and standard industry practices, (c) and flooring product manufacturers' guidelines for the specific floor covering installed. LIMITED-LIFETIME WARRANTY applies only for installations performed by industry-certified professional installers. Visit robertsconsolidated.com or call (866) 435-8665 for warranty detail. 6. TECHNICAL SERVICES For technical assistance or installation questions not covered in this document, please contact our Technical Services Department at (706) 277-5294 U.S.A. / (905) 791-4444 Canada ROBERTS® and the e® logo are registered trademarks of Roberts Consolidated Industries, Inc. · Q.E.P.® is a registered trademark of Q.E.P. Co., Inc. LEED® and its related logo, is a trademark owned by the U.S. Green Building Council® · Microban® is a registered trademark of Microban Products Company. *FloorScore applies to US products only. Roberts Consolidated Industries, Inc. 300 Cross Plains Blvd, Dalton, GA 30721 Customer Service: (866) 435-8665 Technical Support: (706) 277-5294 robertsconsolidated.com Roberts Company Canada, Ltd. 34 Hansen Road, Brampton, ON L6W 3H4 Customer Service: (866) 435-8665 Technical Support: (905) 791-4444 robertsconsolidated.com/ca M2025 12557