Instruction Manual for Townsteel models including: TDC70-T, TDC70-T Track Arm, TDC70-T, Track Arm, Arm
TDC70-T TRACK ARM INSTALLATION ISNTRUCITONS PARTS WITH SLIDE ARM SLIDE ARM INSERT SCREW SLIDE ARM END CAP SLIDE TRACK END CAP WITHOUT SLIDE ARM SLIDE INSERT MOUNTI NG SCREW POWER ADJSUTMENT CHART. inches/[mm] MAX. DOOR WIDTH ADJUSTING CYCLES SIZE EXTERIOR DOOR INTERIOR DOOR HOLD OPEN CLIP ADJUSTMENT SCREW 1 ---- -6 TURNS 2 8.5lb-f* 34''(864) -3 TURNS 3 30''(762) 38''(962) 0 TURNS 4 36''(914) 48''(1219) 12 TURNS C.W. Slide Insert Hold Open Stop INSTALL TRACK ARM - PULL SIDE MOUNTING APPLICATION (RIGHT HAND SHOWN) 120° 3 1/4" [82.5] 19 7/8" [504.8] inches/[mm] 1 1/8" [29] 1 1/8"[28.5] 4 7/8" [123.8] CENTERLINE OF HINGE 11 1/8" [283] 1 1/8" [28.5] 1 5/16" [33.3] Installation Sequence: 1. Use template to locate holes on door and frame. Drill 1/8" pilot holes forthe self-tapping screws. 2. Determine door width, adjust spring power of closer byabove list power adjustment chart. 3. Fasten closer body to door with power adjustment nut away from hinge. 4. Fasten slide track to frame face with open side facing down and with hold open clip end toward hinge edge of door. 5. Place arm to closer at pre-load position of 45° from door frame. 6. Secure arm with arm washer and arm screw. 7. Secure other end of slide arm to track by screwing it to the slide insert. Open door to required opening angle. Then slide stop only/hold open stop up against slider insert and tighten down the stop only/hold open stop via set screw. TDC70-T TRACK ARM INSTALLATION ISNTRUCITONS INSTALL TRACK ARM - PULL SIDE (TOP JAMB) MOUNTING APPLICATION (RIGHT HAND SHOWN) 120° 3/4" 11 1/8" [19] [283] 7/16" [ 11] inches/[mm] 1 13/16" [46.5] 1 1/8" [28.5] 3 1/8" [79.4] CENTERLINE OF HINGE 19 7/8" [504.8] Installation Sequence: 1. Use template to locate holes on doorand frame. Drill 1/8" pilot holes for the self-tapping screws. 2. Determi ne door width, adjust spring power of closer byreferencing power adjustment chart. 3. Fasten closer body to frame with power adjustment nut awayfrom hinge. 4. Fasten slide track to door face with open side facing up and with hold open stop end toward hinge edge of door. 5. Place arm to closer at pre-load position of 45° from door frame. 6. Secure arm with arm washer and arm screw. 7. Secure other end of slide arm to track by screwing it to the slide insert. Open door to required opening angle.T hen slide stop only/hold open stop up against slider insert and tighten down the stop only/hold open stop via set screw. INSTALL TRACK ARM - PUSH SIDE MOUNTING APPLICAITON (LEFT HAND SHOWN) 90° Viewed from Top 3 1/8" [80] 6 5/8" [168.2] 6 5/8" [168.2] 6 5/8" [168.2] HINGE 11/16"[18] inches/[mm] 2 11/16" [68] 1 1/8" [28.5] 1 1/8" [28] 11 1/8" [283] Installation Sequence: 1. Use template above to locate mounting holes on pocket wall and mount closer according to pull side application template. Drill 1/8" pilot holes for the self -tapping screws. 2. Determine door width, adjust spring power of closer byreferencing power adjustment chart. 3. Fasten closer body to door with power adjustment nut away from hinge. 4. Fasten slide track to pocket wall face with open side facing down and with hold open stop end away from hinge edge of door. 5. Place arm to closer at pre-load position of 45° from door frame. 6. Secure arm with arm washer and arm screw. 7. Push arm towards door to pretension closer then secure other end of slide arm to trackby screwing it to the slide insert. Open door to required opening angle. Then slide stop only/hold open stop up against slider insert and tighten down the stop only/hold open stop via set screw.Microsoft: Print To PDF