ICE Cobotics | Robotic Commercial Floor Cleaning Equipment
User Manual for Intelligent Cleaning Equipment ICE models including: i15B Automatic Scrubber, i15B, Automatic Scrubber, Scrubber
31 lug 2022 — HOW TO ORDER PARTS. Only use ICE Company supplied or equivalent parts. Parts and supplies may be ordered from authorized distributor.28 pagine
File Info : application/pdf, 28 Pages, 1.57MB
DocumentDocumentAutomatic Scrubber www.icecobotics.com Operator & Parts Manual i15B 8401902 REV.02(07-2022) OPERATOR MANUAL READ OPERATOR MANUAL CAREFULLY! IMPORTANT: To ensure full warranty protection, please fill out & return your warranty card. Please fill out at time of installation for future reference. Model No. Serial No. Machine Options Sales Rep. Sales Rep. Phone No. Customer ID Number Installation Date HOW TO ORDER PARTS Only use ICE Company supplied or equivalent parts. Parts and supplies may be ordered from authorized distributor. 1. Identify the machine model. 2. Identify the machine serial number from the data label. 3. Ensure the proper serial number is used from the parts list. 4. Identify the part number and quantity. Do not order by page or reference numbers. 5. Provide your name, company name, customer ID number,billing and shipping address, phone number and purchase order number. PROTECT THE ENVIRONMENT Please dispose of packaging materials,old machine components such as batteries, hazardous fluids, including antifreeze and oil, in an environmentally safe way according to local waste disposal regulations. Always remember to recycle. ICE (International Cleaning Equipment) 4242 58Th St Holland,MI,49423 Tel: 866-777-1905 Specifications and parts are subject to change without notice. 2 ICE i15B OPERATOR MANUAL TABLE OF CONTENTS SAFETY PRECAUTIONS......................................................................................................4 MACHINE COMPONENTS...................................................................................................5 MACHINE OPERATION .......................................................................................................6 MACHINE SETUP & INSTALLATION.............................................................................6 WHILE OPERATING MACHINE....................................................................................7 TANK DRAINING.....................................................................................................8 BATTERY CHARGING..........................................................................................8 PREVENTATIVE MAINTENANCE.......................................................................................9 BASIC TROUBLESHOOTING.............................................................................................10 TECHNICAL SPECIFICATIONS......................................................................................11 PARTS LIST................................................................................................12-25 WEARABLE PARTS............................................................................................26 WIRING DIAGRAM....................................................................................27 ICE i15B 3 OPERATOR MANUAL SAFETY PRECAUTIONS This machine is intended for commercial use. It is designed exclusively to scrub hard floors in an indoor environment and is not constructed for any other use. Only use recommended accessories. WARNING: Fire or Explosion Hazard. Keep sparks and open flames away! Keep battery compartment open when charging. All operators shall read, understand and exercise the following safety precautions: 1. Do not operate machine: - Unless you have read and understand the operators manual. - In flammable or explosive areas. - If not in proper operating condition. - In outdoors areas. WARNING: Flammable materials can cause an explosion or fire. Do not use flammable materials in tanks. 2. Before starting machine: - Make sure all safety devices are in place and operate properly. 3. When using machine: - Go slow on inclines and slippery surfaces. - Follow all safety guidelines. - Be very careful when using the machine in reverse. - Reduce speed when turning. - Report and fix any damage to machine prior to operating it. - Never allow children to play on or around. - Do not operate on inclines that exceed 5% (3°). WARNING: Flammable materials or reactive metals can cause explosion or fire. Do not pick up. 4. Before leaving or servicing machine: - Stop on level surface. - Turn off machine. 5. When servicing machine: - Read operators manual thoroughly prior to operating or servicing this machine. - Use manufacturer supplied or approved replacement parts. - Secure machine with wheel blocks prior to jacking the machine up. - Use approved jack or hoist to safely elevate the machine. - Disconnect batteries prior to working on machine. - Avoid moving parts. Do not wear loose fitting clothing while servicing machine. 4 ICE i15B OPERATOR MANUAL MACHINE COMPONENTS 12 3 4 2 3 17 26 16 18 15 25 19 24 20 21 23 14 22 27 28 13 5 6 7 8 9 10 12 11 29 1. Safety Lock-Out Switch 16. Leveling Rod 2. Control Handle 17. Main Power ON/OFF Switch 3. Trigger 18. Battery Discharge Indicator 4. Squeegee Vacuum Hose 19. Vacuum Power ON/OFF Switch 5. Recovery Tank Cover 20. Clear Cover,Battery Charger 6. ICE Logo 21. Connector, On-Board Battery Charger 7. Recovery Tank 22. Clean Water Tank Drain Cover 8. Bucket Fill Port/ Clean-Out Port 23. Ball Valve 9. Solution Tank 24. Battery 10. Scrub head 25. Vacuum Motor, 24VDC 11. Bumper Rollers 26. Brush Motor, 24VDC 12. Caster,1.5Inch,Squeegee Blade Adjustment 27. Solenoid, 24VDC 13. 10 Inch wheels 28. Squeegee Assembly 14. Recovery Tank Drain Hose 29. Filter Assembly 15. Squeegee Lift Lever ICE i15B 5 OPERATOR MANUAL MACHINE OPERATION FOR SAFETY: Do not operate machine unless operator manual is read and understood. 4. To begin scrubbing,first press the safety switch (1),pull the start triggers(2) and push or pull the machine in either direction . PRE-OPERATION 1. IMPORTANT: To prevent vacuum system from clogging, sweep and dust-mop floor. 2. Make sure battery is charged. 3.Check that the brush and squeegee blades are installed. SCRUBBING FLOORS FOR SAFETY: Before Operating machine,follow safety guidelines concerning wet floors. 5. For heavily soiled areas, use the double scrub method. First scrub the soiled area with the vacuum switch turned off then scrub the area a second time with vacuum switch turned on. WARNING: Fire or Explosion Hazard, Do Not Use or Pick Up Flammable Materials. WARNING: Spinning Brush. Keep Hands Away. 1. Pull the handle adjustment lever and adjust the handle to a comfortable operating height. Release the lever to lock the position. MACHINE SET UP & INSTALLATION 2. Press the main power switch to the on ( I ) position. UNCRATING MACHINE Be sure and check packing carton for any damage. Immediately report any damage to carrier. Check the contents of package to ensure that the following items are included: · Machine · 2-12V Batteries · Squeegee assembly · Battery Charger · Brush · Pad Driver INSTALLING BATTERIES 3. Press the vacuum switch to the on ( I ) position. The batteries are already in the machine upon delivery; However you will need to connect the cables to the battery posts. WARNING: Fire or Explosion Hazard. Keep sparks and open flames away! Keep battery compartment open when charging. 1. Turn off the machine. 2. Lift the Recovery tank (see machine components, p5 item #2) to access the battery compartment. 6 ICE i15B OPERATOR MANUAL 3. Connect battery cables to posts as shown in drawing below. RED to POSITIVE and BLACK to NEGATIVE. WARNING: Do not put any flammable materials into solution tank. This can cause an explosion or a fire. Only use recommended cleaning chemicals. Contact your Simple Clean Scrubbers dealer for recommendations on proper chemicals. WHILE OPERATING MACHINE MACHINE SET UP PRE-OPERATION CHECKS 1. Sweep or dust mop the surface to be cleaned. 2. Check battery meter to make sure batteries are fully charged. (See BATTERY CHARGING) 3. Check that squeegee is properly installed. 4. Check that brush / pad is properly installed. MOUNTING THE SQUEEGEE ASSEMBLY 1. Lower the Squeegee lift lever to the downward position. 2. Mount the Squeegee assembly (see machine components, p5 item #28) to the squeegee pivot bracket. make sure the knobs are completely seated into the slots before securing knobs. 3. Connect the vacuum hose to the squeegee assembly. Loop the hose by using the hose clip provided. 4. Check the squeegee blades for proper adjustment. WARNING: Fire Or Explosion Hazard. Do Not Pick Up Flammable Materials Or Reactive Metals. 1. Go slow on inclines and slippery surfaces. Do not operate the machine on inclines that exceed 5% (3°). 2. Do not keep the machine in the same position with pad / brush spinning, keep the machine moving to prevent damage to floor finish. 3. If the squeegee assembly leaves streaks on the floor, raise the squeegee off the floor and wipe the blades down with a damp cloth. Pre-sweep the area to prevent leaving streaks on the floor. 4. Pour a recommended defoamer into the recovery tank if excessive foam appears. WARNING: Do not allow foam to enter the float shut-off screen, vacuum motor damage will result. Foam will not activate the float shut-off screen. 5. Occasionally check the Battery meter, the indi- cator displays the level of the batteries. When meter is in the red, stop scrubbing and recharge the batteries. FILLING THE SOLUTION TANK The machine is equipped with a Solution fill-port (see machine components, p5 item #8 )at the front of the Solution tank, you can fill the solution tank by using a hose or a bucket. When using the bucket, stop filling when the level reaches the bottom edge of the fill-port. NOTE: When filling the solution tank with a bucket, make sure that the bucket is clean. Do not use the same bucket for filling and draining the machine. Red Yellow 2 Yellow 1 Green 2 Green 1 All green lights on: 100% level. Yellow lights on, green lights off : 50% level. Red light on, other lights off: 20% level, the machine should be stopped and the batteries should be recharged. Red light flash: the batteries have already been discharged deeply. ICE i15B 7 OPERATOR MANUAL 6. When the solution tank runs empty, turn off the Brush motor switch and lift the brush head. Keep the squeegee down and continue to vacuum until all the dirty water is picked up. NOTE: See TANK DRAINING section to learn how to drain recovery and solution tanks. TANK DRAINING 1. Turn off the machine. 2. With the squeegee and scrub head in their "up" position, transport machine to approved area for draining tank(s). DRAINING THE RECOVERY TANK Any time scrubbing is completed, or when refilling solution tank, the recovery tank should be drained and cleaned. WARNING: If the recovery tank is not drained when the solution tank has been refilled, foam or water may enter the float shutoff screen and cause damage to the vacuum motor. BATTERY CHARGING WARNING: Fire Or Explosion Hazard. Batteries Emit Hydrogen Gas. Keep Sparks and Open Flame Away. Keep Battery Compartment Propped Open When Charging. 1. Transport the machine to a well ventilated area. 2. Turn the machine off. 3. If charging wet, lead acid, batteries check the fluid level before charging. 4. Connect the charger's AC power supply cord to a properly grounded receptacle. 5. The charger will automatically begin to charge, you can watch the charging status on the window (machine components, p5 item #20), once the charging cycle begins, the indicator lights will progress from red, yellow to green. When the green indicator light comes on, the charging cycle is done. Unplug the charger cord. NOTE: The machine will not operate when charging. 1. While holding the drain hose (see machine components, p5 item #10) upward, remove the cap and lower hose to drain. 2. Open the recovery tank cover and rinse out the tank. Use a rag to remove any excess dirt. Clean the float shut-off screen and debris tray located in the recovery tank . DRAINING THE SOLUTION TANK Any time scrubbing operation is completed, the solution tank should be drained and cleaned. 1. Pull the solution clear tube(see machine com- ponents, p5 item #22) off the hose fitting, this will allow the solution to flow freely into a bucket or floor drain. 2. Remove the cover of the filter assembly to drain the solution tank, check the filter screen and clean up it if necessary. 3. Rinse the solution tank with clean water after every use. This will help prevent chemical buildup and clogging of the solution lines. 4. After rinsing out the tank, securely reconnect the tank level hose to the hose fitting, replace the filter assembly cover and be sure the filter screen and the "O" ring is in the correct position. 8 ICE i15B OPERATOR MANUAL PREVENTATIVE MAINTENANCE WARNING: Before performing any maintenance on the machine, be sure that the power is turned off, or the batteries are disconnected! WARNING: Batteries emit hydrogen gas and an explosion o fire can result. Keep sparks and fire away from batteries at all times. WARNING: Whenever servicing batteries, be sure to wear protective gloves. Avoid contact with battery acid at all times. WARNING: Repairs are to be completed by Authorized service centers only. Any repairs completed by unauthorized persons will void the warranty. NOTE: For the best machine performance, keep batteries properly charged at all times. Do not let them sit in a discharged condition. DAILY MAINTENANCE 1. Remove pad driver/ brush and clean with ap- proved cleaner. 2. Drain recovery and solution tanks completely and rinse out with clean water. Visually check the recovery tank for debris and clean out as necessary. 3. Raise the squeegee assembly off floor and wipe it down with a damp towel. Be sure to store the squeegee in the up position. 4. Remove the float shut-off assembly and rinse it out with clean water. 5. Clean machine with an approved cleaner and a damp towel. 6. Recharge the batteries. 7. Check the condition of the squeegee blade wiping edge, rotate blade if worn. 1. Always follow the battery charging directions as outlined in the BATTERY CHARGING section of this manual. 2. Keep battery tops and terminals free from corrosion. A strong solution of baking soda and water is the best way to keep the batteries corrosion free. DO NOT ALLOW THE BAKING SODA / WATER SOLUTION TO ENTER THE BATTERY CELLS. 3. Use a wire brush with the baking soda solution to properly clean the battery posts and connections. 4. Check battery connections for wear and loose terminals. Replace if necessary. MONTHLY MAINTENANCE 1. Clean the battery tops to prevent corrosion. 2. Check for loose battery cable connections. 3. Inspect and clean the recovery tank cover seal. Replace it if damaged. 4. Lubricate all grease points and pivot points with silicon spray and approved grease. 5. Check the machine for loose nuts and bolts. 6. Check the machine for leaks. MOTOR MAINTENANCE 1. Contact your dealer for any motor maintnance. 2. Motor should have the brushes checked every 250 hours. Brushes should be replaced when they are worn to a length of 10 mm or less. MACHINE STORAGE 1. Always store the machine indoors. 2. Always store the machine in a dry area. 3. Always store the machine in its upright position. 4. Always store the machine with the pad driver/ brush raised off the floor. 5. Always store the machine with the squeegee assembly raised off the floor. 6. If storing in an area which may reach freezing temperatures, be sure to drain all fluids from the machine prior to storage. Any damage caused by freezing temperatures will not be covered by the warranty. 7. Drain the recovery tank. 8. Drain the solution tank of all fluid. BATTERY MAINTENANCE ICE i15B 9 OPERATOR MANUAL BASIC TROUBLESHOOTING PROBLEM CAUSE Batteries need to be charged Machine operate will not Bad battery(s) Loose battery cable Control handle trigger not pulled Tripped brush motor blown fuses Brush motor not operate will Bad brush motor switch Faulty brush motor or wiring Worn motor carbon brushes Bad vacuum motor switch Vacuum motor Bad vacuum motor relay will not operate Faulty vacuum motor or wiring Worn Motor carbon brushes Ball valve is shut off Little or no solu- Clogged solution tank filter or solution tion flow hose Clogged solution Solenoid valve Recovery tank is full Loose drain hose cap Clogged float shut-off screen located in recovery tank Clogged squeegee assembly Worn squeegee blades Incorrect squeegee blade deflection Poor water pick up Loose vacuum hose connections Clogged vacuum hose Damaged vacuum hose Recovery tank lid not in place Damaged recovery tank cover seal Faulty vacuum motor Low battery charge Low battery charge Defective batteries Short run time Batteries need maintenance Faulty battery charger SOLUTION Charge batteries Replace battery(s) Tighten loose cable Pull control handle trigger Replace fuse Replace brush motor switch Contact ICE service Dealer Contact ICE service Dealer Replace vacuum motor switch Replace vacuum motor relay Contact ICE service Dealer Contact ICE service Dealer Turn on the ball valve Clean solution tank filter or flush out solution hose Remove valve and clean Drain recovery tank Tighten cap Clean screen Clean squeegee assembly Replace or rotate squeegee blades Adjust squeegee blade height Secure hose connections Remove clogged debris Replace vacuum hose Properly position cover Replace seal Contact ICE service Dealer Recharge batteries Fully recharge batteries Replace batteries See BATTERY MAINTENANCE Repair or replace battery charger 10 ICE i15B OPERATOR MANUAL MODEL DIMENSIONS L DIMENSIONS W DIMENSIONS H WEIGHT TECHNICAL SPECIFICATIONS i15B Brush Assist 31in / 790 mm 18.5 in / 468 mm 27 in / 690 mm 93.7 lbs / 42.5Kg WEIGHT WITH BATTERIES 140 lbs /63.5 Kg RECOVERY TANK CAPACITY 5Gal / 19 L SOLUTION TANK CAPACITY SQUEEGEE WIDTH CLEANING PATH WIDTH PRODUCTIVITY RATE DRIVE SYSTEM BRUSH MOTOR VACUUM MOTOR WATER LIFT - AIR FLOW BATTERIES RUN TIME PER CHARGE VOLTAGE DC DECIBEL RATE AT OPERATOR'S EAR, INDOORS GRADE LEVEL, MAX 4Gal / 15 L 18 in / 450 mm 15 in / 381 mm (Disk) 13993 ft² /1300 h Brush Assisted 0.27hp / 0.2KW 140 RPM 0.54hp / 0.4KW 45 in / 1,143 mm 2-1233Ah @ 20 hr 1.2 Hours 24V 78dB(A) 5% (3°) ICE i15B 11 PARTS LIST RECOVERY TANK GROUP 12 ICE i15B PARTS LIST RECOVERY TANK GROUP DIA PART NO. NUMBER DESCRIPTION SERIAL NUMBER NO. REQ'D 1 8401204 RECOVERY LID 1 2 8401205 LOWER LID OF RECOVERY TANK 1 3 1421409 FLAT WASHER M4×9×0.8 8 4 1321110 SCREW,ST3.5×10 9 5 8401207 RECOVERY TANK COVER SEAL 60037100101-- 60037100460 1 8401217 RECOVERY TANK COVER SEAL 60037100461-- 1 6 8401206 RECOVERY TANK COVER SEAL 1 7 8401208 FLOAT 1 8 1421425 FLAT WASHER,4.3×25×1.5 1 9 4010316 ICE LOGO 1 10 8401201 RECOVERY TANK 1 11 8401210 VACUUM HOSE 1 12 8401211 DRAIN HOSE 1 1962032 CLAMP 13 1962033 CLAMP 60037100101-- 60037100460 1 60037100461-- 1 14 8401215 RECOVERY TANK COVER GROUP 1 NOTES 1.DIA NO.5,8401207 and 8401217,the installation and use mode are fully compatible,Follow-up maintenance unified use 8401217; 2.DIA NO.13,1962033 is optimized material, Follow-up maintenance unified use 1962033 ICE i15B 13 PARTS LIST SOLUTION TANK GROUP 14 ICE i15B PARTS LIST SOLUTION TANK GROUP DIA PART NO. NUMBER DESCRIPTION 1 1221612 SCREW,M6×12 2 1422616 LOCK WASHER, M6 3 1421616 FLAT WASHER M6×16×1 4 8401212 VACUUM SEAL 5 8401213 FILTER 6 8401203 VACUUM MOTOR,24VDC 7 8401209 MOUNTING PLATE 8 1421409 FLAT WASHER M4×9×0.8 9 1422411 LOCK WASHER, M4 10 1321213 SCREW,ST4×13 8310208 ISOLATER, M6 11 8401145 ISOLATER, M6 12 8401202 FRONT FILL COVER 13 8050153 CHAIN,FRONT COVER 14 1321110 SCREW,ST3.5×10 15 8401101 SOLUTION TANK 16 8401121 SOLUTION DRAIN CAP 17 8401102 MAIN FRAME 18 1421824 FLAT WASHER M8×24×2 19 1422821 LOCK WASHER, M8 20 1021820 SCREW,M8×20 21 1421828 FLAT WASHER M8×28×3 22 8401108 WHEEL,10 INCH 23 8401127 BUSHING 24 1511525 SCREW,M5×25,HEX SOCKET 25 4010405 CORD WRAP 26 1221310GL SCREW,M3×10,HEX HEAD 27 8401131 HOSE CLAMP 28 1221410 SCREW,M4×10 29 8401133 DECAL,SWITCH 30 6210503 ROCKER SWITCH 31 1123305 NUT,LOCK M3 32 8401104 REAR COVER 33 1222512 SCREW,M5×12 SERIAL NUMBER NO. REQ'D 4 6 4 1 1 1 1 8 8 4 60037100101--60037100203 4 60037100204-- 4 1 1 2 1 1 1 4 6 6 2 2 2 4 2 4 2 6 1 1 2 1 2 ICE i15B 15 PARTS LIST SOLUTION TANK GROUP DIA PART NO. NUMBER DESCRIPTION SERIAL NUMBER NO. REQ'D 34 8114707 RELAY 40A 2 35 1123406 NUT,LOCK M4 2 8401107 BATTERY CHARGER,24V,SPE 60037100101--60037100723 1 36 8401109 BATTERY CHARGER,24V,QQE 60037100724-- 1 37 8401103 MOUNTING PLATE 1 38 8401132 MOUNTING PLATE 1 39 1421612 LOCK WASHER, M6 2 40 1021616 SCREW M6×16 2 41 8401711 BATTERY CONNECT CABLE,RED 2 42 8401712 BATTERY CONNECT CABLE,BLACK 1 43 8401713 BATTERY CONNECT CABLE,RED 1 44 8401710 BATTERY (LEOCH AGMU1 (12V 35AH)) 2 45 8112030 CHARGER CORD (FOR US) 1 46 8401906 INDICATED LABEL 60037100514-- 1 47 1421618 FLAT WASHER M6×18×1.6 60037100204-- 4 48 8401147 SHIELDED PIECE 60037100514-- 1 49 1421510 FLAT WASHER M5×10×1.0 2 50 1123507 NUT M5 2 NOTES 1.DIA NO.11,8401145 is optimized material.Follow-up maintenance unified use 8401145. 2.DIA NO.47,1421618 FLAT WASHERwhich is matching with 8401145(DIA NO.11). 3.DIA NO.36,8401107 and 8401109,they are different in the power interface position size. So,the aftermarket component of the 8401107 is"8401109 1pc+8401103 1pc", and the aftermarket component of the 8401109 is still "8401109 1pc". 16 ICE i15B HANDLE ASSEMBLY PARTS LIST ICE i15B 17 PARTS LIST HANDLE ASSEMBLY DIA PART NO. NUMBER DESCRIPTION 1 8014063 BATTERY CAPACITY METER 2 1885301 POWER CONTROL SWITCH 3 1211410 SCREW, M4×10 4 8401704 DECAL,CONTROL PANEL 5 8401703 CONTROL PANEL 6 1512625 SCREW, M6×25 7 1421616 FLAT WASHER M6×16×1.0 8 8401401 THE HANDLE BACK COVER 9 1512635 SCREW, M6×35 10 1211512 SCREW, M5×12 11 1434500 TOOTH WASHER,5 12 8401402 HANDLE TUBE 13 8401405 CONTROL LINE PROTECTION RING 14 8401403 PULL ROD 15 4010207 SEAT,SPRING 16 4010216 SEAL,SEAT 17 4010208 SPRING,LEVELING 18 1111403 NUT M4 19 4010211 INSERT 20 1511530 SCREW, M5×30 21 1511540 SCREW, M5×40 22 1521620 SCREW, M6×20 23 4010110 SHAFT 24 4010114 WASHER 25 1222512 SCREW, M5×12 26 1521845 SCREW, M8×45 27 5012416 HANDLE,STAND,LEFT 28 1123608 NUT M6 29 1212410 SCREW, M4×10 30 4010212 COVER 31 4010202 COVER,SEAT GEAR 32 8401404 GEAR 33 4010201 MOUNTING BASE,GEAR 34 1123507 NUT M5 35 8401415 MOUNTING BRACKET 36 1421510 FLAT WASHER M5×10×1.0 37 1422616 LOCK WASHER, M6 38 1421612 FLAT WASHER M6×12×1.0 39 5012415 HANDLE,STAND,RIGHT 40 1421618 FLAT WASHER M6×18×1.6 41 8113111 NYLON FLAT WASHER 12.9×25.4×0.8 18 SERIAL NUMBER NO. REQ'D 1 1 4 1 1 2 4 1 2 4 4 1 1 1 1 1 1 1 1 4 2 4 1 1 1 3 1 4 2 2 1 1 1 8 1 2 4 4 1 3 2 ICE i15B DIA PART NO. NUMBER 42 8401411 43 8014101 44 8401407 45 8401413 46 1021630 47 1021620 48 4010317 49 1211408 50 1123406 51 1421412 52 4010304 53 8113104 54 4010330 55 4010331 56 4010314 57 1221406 58 4010311 59 4010323 60 1211325 61 1434300 62 4010308 63 4010307 64 4010333 65 8401408 66 4010316 HANDLE ASSEMBLY DESCRIPTION SQUEEGEE LIFT CABLE LIFTING CABLE SPACER HANDLE,SQUEEGEE LIFT AXLE SLEEVE HEX HEAD BOLT M6×30,SS HEX HEAD BOLT M6×20,SS SEAT,BALL SCREW, M4×8 NUT M4 FLAT WASHER M4×12×1.0 LEVELONG ROD BALL KNOB M8 TRIGGER,SWITCH,RIGHT TRIGGER,SWITCH,LEFT PIN SCREW M4×6 CLAMP,CORD SPRING,SWITCH SCREW M3×25 TOOTH WASHER M3 SWITCH SAFETY,BUTTON SPRING,SAFTY FRONT COVER ICE,LOGO PARTS LIST SERIAL NUMBER NO. REQ'D 1 1 1 1 1 1 1 2 1 1 1 1 1 1 4 2 1 1 2 2 1 1 1 1 1 ICE i15B 19 PARTS LIST SCRUB HEAD GROUP 20 ICE i15B DIA PART NO. NUMBER 1 8401310 2 8401303 3 1123810 4 1422821 5 1421824 6 1421816 7 1021835 8 1021620 9 1422616 10 1421616 11 8401512 12 1123608 13 8401511 14 8401515 15 1421622 16 1421409 17 1221410 18 8401516 19 8401301 20 8401513 21 8401514 22 1421612 23 1021616 24 8401305 25 1421828 26 1021825 27 9050015 28 9040015 SCRUB HEAD GROUP DESCRIPTION BRUSH MOTOR,24VDC,KIT MOUNTING PLATE LOCK NUT M8 WASHER LOCK 8 FLAT WASHER M8×24×2.0 FLAT WASHER M8×16×1.0 SCREW M8×35 SCREW M6×20 WASHER LOCK 6 FLAT WASHER M6×16×1.0 CONNECTING ROD LOCK NUT M6 SQUEEGEE MOUNT BRACKET SPRING FLAT WASHER M6×22×2.0 FLAT WASHER M4×9×1.0 SCREW M4×10 SCREW BRUSH PLATE COVER BRACKET,BRUSH MOTOR MOUNT,BRUSH MOTOR FLAT WASHER M6×12×1.0 SCREW M6×16 BRUSH PLATE HOLDER FLAT WASHER M8×28×2.0 SCREW M8×25 15"BRUSH 15"PAD DRIVER OPTION PARTS LIST SERIAL NUMBER NO. REQ'D 1 1 2 5 2 2 2 2 10 2 2 3 1 2 2 3 3 1 1 1 1 8 8 1 1 1 1 1 ICE i15B 21 PARTS LIST SQUEEGEE GROUP 22 ICE i15B PARTS LIST SQUEEGEE GROUP DIA PART NO. NUMBER DESCRIPTION SERIAL NUMBER NO. REQ'D 1 1127510 NUT M5 6 2 1421515 FLAT WASHER M5×16×1.0 8 3 8401504 CLAMP ASSEMBLY,REAR 1 8401503 SQUEEGEE BLADE,REAR,LINATEX 1 4 8401543 SQUEEGEE BLADE,REAR,PU 1 5 1021650 HEX HEAD BOLT M6×50 2 6 8401501 SQUEEGEE HOUSING 1 7 1123507 NUT M5 3 8 8401517 AXLE SLEEVE 3 9 8401518 SQUEEGEE WHEEL,1.5INCH 3 10 1033535 SCREW M5×35 3 8401502 SQUEEGEE BLADE,FRONT,LINATEX 1 11 8401542 SQUEEGEE BLADE,FRONT,PU 1 12 8401505 CLAMP ASSEMBLY,FRONT 1 13 1033540 SCREW M5×40 2 14 1033545 SCREW M5×45 4 15 7000177 KNOB 2 16 8401506 PLATE,COUPLING 1 17 8401507 ANGLE COUPLING 1 18 1421510 FLAT WASHER M5×10×1.0 2 19 1422513 WASHER LOCK 5 4 20 1321316 SELF-TAPPING SCREW ST4.8×16 2 21 1321310 SELF-TAPPING SCREW ST4.8×10 2 22 8411607 BUMPER WHEEL 2 23 1421511 FLAT WASHER M5×12×1.0 3 24 8401500 SQUEEGEE ASSEMBLY,LINATEX 1 NOTES: 1.DIA NO.4,8401503 is standard material and 8401543 is alternative material; 2.DIA NO.11,8401502 is standard material and 8401542 is alternative material. ICE i15B 23 PARTS LIST SOLUTION FLOW GROUP 24 ICE i15B SOLUTION FLOW GROUP DIA PART NO. NUMBER DESCRIPTION 1 8018006 BALL VALVE,3/8 2 8401116 ELBOW,3/8 3 8401142 CLAMP 4 8401134 TUBING,ID=8MM L=300mm 5 8401115 FILTER ASSEMBLY 6 8401111 BASE,FILTER ASSEMBLY 7 8401114 O RING 8 8401112 SCREEN,FILTER 9 8401113 CAP,FILTER ASSEMBLY 10 8401135 TUBING,ID=8MM L=120mm 11 8401129 ELBOW 12 1962016 CLAMP 13 8401136 TUBING,ID=12MM L=120mm 14 1221410 SCREW M4×10 15 1422411 WASHER LOCK 4 16 1421409 FLAT WASHER M4×9×1.0 17 8018007 SOLENOID VALVE,24VDC 18 8401137 TUBING,ID=12MM L=200mm 19 8401138 TUBING,ID=8MM L=150mm SERIAL NUMBER PARTS LIST NO. REQ'D 1 3 6 1 1 1 1 1 1 1 2 4 2 2 2 2 1 1 1 ICE i15B 25 PARTS LIST DIA PART NO. NUMBER 1 8401108 2 8411607 3 8401518 4 8401502 5 8401503 6 9040015 7 9050015 WEARABLE PARTS DESCRIPTION WHEEL, 10INCH, WITH BEARINGS BUMPER WHEEL SQUEEGEE WHEEL,1.5INCH FRONT SQUEEGEE BLADE, LINATEX REAR SQUEEGEE BLADE, LINATEX PAD HOLDER, 15 INCH BRUSH, 15 INCH NO. REQ'D 2 2 3 1 1 1 1 26 ICE i15B WIRING DIAGRAMi15B 18AWG RED 20AWG RED 1 10AWG RED 20AWG RED 2 10AWG RED 10AWG RED 10AWG BLK 18AWG BLK 20AWG RED 3 20AWG YEW 3 20AWG GRN 3 20AWG YEW 4 20AWG GRN 5 20AWG BLK 0 20AWG BLK 0 20AWG BLK 0 12AWG RED 1 12AWG RED 1 12AWG RED 6 18AWG RED 6 12AWG RED 6 12AWG RED 7 12AWG RED 7 18AWG BLK 0 12AWG BLK 0 12AWG BLK 0 CERTIFICATE OF QUALIFIED MODEL: INSPECTOR: SERIAL NO: DATE: ICE Cobotics(Guangdong)Co.Ltd (TEL): +86769 8186 9000 (FAX) : +86769 8186 3000