Bestway Steel Pro™ Pools

Welcome

Thank you for choosing a Bestway product. This manual provides essential information for the safe installation, use, and maintenance of your Steel Pro™ pool. Please read carefully and keep for future reference.

Safety First: Essential Warnings and Precautions

General Safety: Always read, understand, and follow all information in this manual before installing and using the swimming pool. While these guidelines cover common risks, they cannot anticipate all potential dangers. Exercise caution, common sense, and good judgment during all water activities.

Non-Swimmer Safety: Continuous, active, and vigilant supervision by a competent adult is mandatory for weak swimmers and non-swimmers, especially children under five, who are at the highest risk of drowning. Designate a supervisor each time the pool is in use. Weak swimmers or non-swimmers should wear personal protection equipment.

Safety Devices: To prevent drowning, secure pool access with a protection device. Consider installing a barrier and securing doors/windows to prevent unauthorized access. Pool covers, alarms, and barriers are helpful but do not replace adult supervision.

Safety Equipment: Keep rescue equipment (e.g., a ring buoy) and a working phone with emergency numbers near the pool.

Safe Pool Use: Encourage all users, especially children, to learn how to swim. Learn and refresh Basic Life Support (CPR). Instruct all users on emergency procedures. Never dive into shallow water. Do not use the pool under the influence of alcohol or medication. Remove pool covers completely before entering. Maintain water hygiene and proper treatment as per the manual. Store chemicals out of reach of children. Display safety signage within 2 meters of the pool.

Pictograms: ⚠️ (Warning), ❌ (Incorrect), ✔️ (Correct), ?? (No Diving), ?? (No Running), ?‍?‍?‍? (Supervision Required).

Pool Care: Regularly monitor bolts and screws, removing splinters or sharp edges. Do not leave a drained pool outside as it can deform or be displaced by wind.

Pump & Ladder Safety: If using a filter pump, refer to its manual. Never operate the pump when people are in the pool. If using a ladder, refer to its manual. Ensure ladders are placed on a horizontal surface and do not exceed their weight limit.

Choosing the Correct Location

Selecting the right location is crucial for pool stability and safety. Ensure the chosen surface meets these technical characteristics:

• Load Bearing: The surface must uniformly support the combined weight of the water and users throughout the pool's installation. Consider that water may spill, potentially softening the surface and reducing its load-bearing capacity.
• Level Surface: The ground must be perfectly flat and smooth. An inclined or uneven surface can cause unbalanced loading, potentially damaging the liner and frame, leading to collapse and injury.
• Leg Stability: Regularly check the position of vertical legs and U-supports. They must remain level with the pool bottom. If legs sink, drain the pool immediately and re-level or reinforce the ground.
• Clearance: Position the pool away from objects children could use to climb into it. Ensure no overhead power lines or trees are present, and check for underground utility lines or cables.
• Drainage: Place the pool near an adequate drainage system for overflow or emptying.
• Object-Free: The surface must be clear of any objects, as the water's weight can cause them to damage or puncture the pool liner.
• Vegetation-Free: Remove aggressive plants and weeds, as their roots can grow through the liner and cause leaks. Eliminate grass or vegetation that might cause odors or slime.
• Proximity: Avoid placing the pool near house entrances. Do not place furniture or equipment around the pool, as spilled water can cause damage.

Suggested Surfaces: Grass, ground, concrete, or other suitable surfaces.

Not Suggested Surfaces: Mud, sand, gravel, decks, balconies, driveways, platforms, soft/loose soil.

Regulations: Check local city council by-laws regarding fencing, barriers, lighting, and safety requirements.

Components List

Before assembly, check all parts. Note: Some parts may already be installed on the pool.

Installation Guide

Estimated Time: 10-20 minutes for 2-3 people (excluding ground preparation and filling).

Assembly: The frame pool can be assembled without tools. To prolong the life of your pool, it is recommended to sprinkle the top rail with talcum powder (not included) before assembly.

Important: Assemble the pool in the order shown in the illustrations. Do not drag the pool on the ground to avoid damaging the liner on sharp objects. Bestway is not responsible for damage caused by mishandling or failure to follow instructions.

Diagrams: Illustrations are for guidance only and may not reflect the actual product or scale.

Assembly Steps:

1. Frame Assembly: Connect the frame parts as shown in the diagrams.
2. Liner Setup: Carefully unfold the liner on the prepared ground.
3. Water Filling: Begin filling the pool with water.

(Note: Specific assembly diagrams are not included in this text-based output but would be visually represented in the original PDF.)

Filling the Pool with Water

ATTENTION: Never leave the pool unattended while filling.

1. Fill the pool until the water reaches the drain valve.
2. Turn off the water supply. Check that the water level is even on all sides to ensure the pool is level. If not level, drain the water and re-level the ground. Never move a pool with water in it.
3. If the pool is level, fill to the lowest pump valve.
4. Turn off the water supply and check valves for a secure fit.
5. Fill the pool until the water reaches the welding line, approximately 4-12 cm (1.6"-4.7") from the top edge. DO NOT OVERFILL, as this can cause the pool to collapse. During heavy rainfall, you may need to drain some water to maintain the correct level.
6. Check for any leaks at valves or seams. Do not add chemicals until all leaks are addressed.

Important Notes:

• Pools can contain significant pressure. Bulging or uneven sides indicate the pool is not level, which can lead to bursting and sudden water discharge, causing injury or property damage.
• Do not use the pump while the pool is in use.
• During the swimming season, the filtration system should run daily to ensure complete water renewal.

Pool Maintenance

Adhering to these guidelines is crucial for your health and your children's safety.

Chemical Treatment:

• Use chemical tablets with a Chemconnect or Chemical Floater dispenser (sold separately if not included).
• IMPORTANT: Do not use granular tablets or throw tablets directly into the water, as they can damage the material and discolor the PVC.
• Liquid Chemicals: Add liquid chemicals in small doses to the center of the pool to avoid direct contact with the PVC surface. Remove dispensers when the pool is in use.
• Water Testing: After chemical treatment and before use, test water chemistry with a test kit.

Recommended Water Parameters:

Warranty Note: Damage from chemical imbalance is not covered by warranty. Handle pool chemicals with care; they are toxic. Consult your local pool supplier for more information. Overuse of chemicals can discolor the pool material and damage the liner.

Keeping Your Pool Clean:

• Consult your local pool supplier for advice and chemicals.
• Keep a bucket of water nearby to clean feet before entering the pool.
• Cover the pool when not in use.
• Skim the pool surface regularly to remove debris.
• Check and wash the filter cartridge regularly.
• Gently clean any scum from the top ring with a cloth.
• Monitor water levels, especially during rain, and drain excess water if levels exceed the specified limits.

Proper maintenance maximizes the pool's lifespan. The filtration system should run daily during the season.

Repair, Dismantling, and Storage

Repair: For leaks, use the provided underwater adhesive repair patch. Instructions are available in the FAQs on the Bestway website.

Dismantling:

1. Unscrew the drain valve cap counter-clockwise.
2. Connect a hose to the adapter and direct it to a drainage area (check local regulations).
3. Screw the hose adapter's control ring clockwise onto the drain valve to open it and start draining. Water flow can be controlled by the ring.
4. Once drained, unscrew the control ring to close the valve.
5. Disconnect the hose.
6. Screw the cap back onto the drain valve.
7. Air dry the pool completely.

ATTENTION: Do not leave the drained pool outside.

Storage:

1. Remove, clean, and dry all accessories and spare parts.
2. Once the pool is completely dry, sprinkle with talcum powder to prevent sticking, then fold carefully. Incomplete drying may lead to mold.
3. Store the liner and accessories in a dry place at a moderate temperature (5°C to 38°C / 41°F to 100°F).
4. Store the pool and accessories similarly during the rainy season.
5. Improper draining can cause injury or property damage.
6. It is strongly recommended to disassemble the pool during the off-season (winter months) and store it in a dry location out of children's reach.

Warranty Registration

Get a free 6-month warranty extension by registering your product within 30 days of purchase at WWW.REGISTREERBESTWAY.BE (or relevant regional site). This offer is valid for specific countries including Germany, Belgium, France, Italy, Luxembourg, and Spain.