Telematics & Data Analytics | Sensata INSIGHTSInstallation Request | Sensata INSIGHTS
Installation Guide for SMARTWITNESS models including: KP2 Pro, 4G LTE Fleet Telematics Dash Cam, KP2 Pro 4G LTE Fleet Telematics Dash Cam
7 lug 2022 — DISCLAIMER. The KP2 installation featured in this guide is designed for professional installation. SmartWitness assumes installers possess knowledge of ...
KP2 Setup | SmartWitness
File Info : application/pdf, 15 Pages, 11.24MB
DocumentDocumentKP2 PRO INSTALLATION GUIDE DISTRACTION DETECTED Version 4.0 Last updated 7/7/2022 EVENT TRIGGER KP2 PRO INSTALLATION GUIDE TABLE OF CONTENTS Please follow along with this guide for details on proper device installation and calibration. PACKAGE CONTENTS.................................................................... 3 KP2 FEATURE REFERENCE............................................................4 HOW TO INSTALL YOUR KP2 .......................................................6 Prepare Your KP2...............................................................................6 Attach Your Camera to the Windshield ........................................ 7 Connect the KP2 to Your Vehicle's Power Source.....................8 HOW TO TEST YOUR INSTALLATION .........................................9 HOW TO CALIBRATE YOUR G-SENSOR...................................10 HOW TO CONFIGURE KP2 SETTINGS...................................... 11 COMPLETE YOUR INSTALLATION/SUPPORT ......................... 12 Not an Installer?............................................................................... 12 LED & BUZZER SPECIFICATIONS............................................... 13 TECHNICAL SPECIFICATIONS.................................................... 14 SMARTWITNESS KP2 PRO INSTALLATION GUIDE 2 PACKAGE CONTENTS KP2 Vehicle Recorder Power Cable 1 From Bracket Removable Wedge Block (Driver-Facing Camera Ordered Separately) Torx® Wrench Power Cable 2 (3-Wire Type) Square Adhesive Cable Clips (x5) *64GB SD Card (Pre-Installed) *128GB SD Available Upon Request Nano SIM Card (Pre-Installed) Double-Sided 3MTM Tape (One Adhered to Bracket, One Extra Pc.) Alcohol Prep Pad (x2) SMARTWITNESS KP2 PRO INSTALLATION GUIDE 3 KP2 FEATURE REFERENCE FRONT Camera Lens Lens Angle Lock SIDE Windshield Bracket Unscrew the right-side bracket. Remove the KP2 from the bracket to adjust camera angle or insert/remove SIM/SD card. Applied screws for design purpose only. SMARTWITNESS KP2 PRO INSTALLATION GUIDE 4 KP2 FEATURE REFERENCE SIDE COVER OPEN BACK 2nd Camera (Model: KP2-DFC) Ecall/Panic Button LED Types: Warning LED (RED) Record LED (BLUE) Network LED (GREEN) Release Tab Nano SIM Slot (4FF) Micro SD Card Slot Memory SD Card Slot Bluetooth Pairing Button SMARTWITNESS KP2 PRO INSTALLATION GUIDE 5 HOW TO INSTALL YOUR KP2 Prepare Your KP2 DISCLAIMER The KP2 installation featured in this guide is designed for professional installation. SmartWitness assumes installers possess knowledge of current, generally accepted industry installation standards and practices. The process outlined in this document accounts for driver positioning on the left side of the vehicle. Please adjust the installation accordingly if you're working with driver positioning on the vehicle's right side. 1. Use the Torx® wrench provided in the package contents to open the side cover of the device. You'll notice that both the microSD and SIM cards come pre-installed. See Diagram A. 2. Keep the side panel open. It allows you to remove the KP2 from its mount and adjust the driver- and road-facing cameras. Prep the cameras for adjustments. · Loosen the KP2's top screw (for the road-facing lens) with the Torx wrench. · The driver-facing camera has a release tab next to the lens. Note: You must order the KP2's driver-facing camera as a separate accessory. White-label KP2s are exceptions. 3. Go to your vehicle, and hold your KP2 where you'll mount the bracket. Your KP2 placement should reduce the windshield's blind-spot footprint, with the road-facing camera within the top 2" of the wiper path. The device should reside close to the center of the windshield. See Diagram B. Note: The driver-facing lens needs complete visibility of the driver, without any physical or visual obstructions. Ensure your vehicle's sun visor doesn't complicate camera visibility. Diagram A 4. While holding the KP2 in place, rotate each camera until they're at the desired angle. 5. Remove the protective decals from each lens. 6. Use the Torx wrench to tighten the top screw on the KP2 and lock the road-facing camera's position. Diagram B Once you've secured the road-facing camera, please go on to Attach Your Camera to the Windshield. SMARTWITNESS KP2 PRO INSTALLATION GUIDE 6 HOW TO INSTALL YOUR KP2 Attach Your Camera to the Windshield Your vehicle's windshield temperature shouldn't be too hot or cold. SmartWitness recommends installing your KP2 in moderate temperatures (50°F~80°F). If in severe cold weather, use the vehicle defrosters to warm and dry out the windshield. Ensure your windshield is dry and has no chips or cracks before installation. If the windshield is compromised, device application may cause chips or cracks to spread. 1. Clean the windshield with your alcohol wipe. See Diagram C. Allow time to dry. 2. Remove any film left over from the solution. 3. Remove the plastic from the tape on the mounting bracket. 4. When attaching the KP2 to the windshield, position the bracket so it's flush with the windshield. Note: When installing the KP2 in a truck, FMCSA mandates that the device's camera is in the top 2" of the windshield wiper sweep. 5. Apply your KP2 to the windshield, and maintain pressure for at least 30 seconds. 6. After mounting your KP2, use the Torx® wrench to re-secure the device's side cover. This locks both camera positions in place. Diagram C 7. Go outside the vehicle, and check whether 80%90% of the tape's surface area connects with the glass. Momentarily apply pressure where the camera doesn't connect to the glass (if necessary). Once the device is correctly attached to the windshield, continue to Connect the KP2 to Your Vehicle's Power Source. SMARTWITNESS KP2 PRO INSTALLATION GUIDE 7 HOW TO INSTALL YOUR KP2 Connect the KP2 to Your Vehicle's Power Source If you are not a professional technician, click here to request installation from an approved SmartWitness installer. By continuing this process without a certified installer, you accept the ramifications of tampering with your vehicle's power source. 1. Turn off your vehicle. 2. Take your main power cable, and place it where it'll reside alongside the vehicle's headliner and A-pillar. This shows you where to route the cable and how much slack to leave to connect the adapter cable to the vehicle's power source. 3. Clean the space where the cable clips will reside with an alcohol wipe. Allow time to dry. 4. Once the windshield is dry, attach clips where you'll place the cable. Ensure the clips are evenly spaced, around 6" apart. Keep the opening of the clips face up, and ensure the cable remains taut. 5. Slide the power cable from the bracket into the clips. Your cable should look like Diagram D. Diagram D 6. Route the power cable around the side and behind interior panels or weather stripping to secure it. See Diagram E. The cable should fall near the vehicle's fuse box/power source. 7. Attach the KP2 main power cable to one of the compatible power adapter options. Let's use the bare 3-wire connection adapter provided in the box for this walk-through. See Diagram F. Note: SmartWitness provides optional power adapter accessories separately. 8. Identify each connection wire on the 3-wire adapter: black, white and red. Note: Ensure your 3-wire connection has fuses attached to the red and white wires within 4" of the power source. This is a requirement that protects both your device and your vehicle. Diagram E 9. Connect each wire to its associated power source. · Black ground or battery (-) · White true ignition or ACC · Red power or battery (+) Go to How to Test Your Installation to ensure you've properly applied power to your device. Diagram F SMARTWITNESS KP2 PRO INSTALLATION GUIDE 8 HOW TO TEST YOUR INSTALLATION After installing the KP2 in your vehicle, test whether it is operational. 1. Turn on your vehicle. Your camera should power on. 2. You'll see a Red/Blue/Green light sequence during your camera's boot-up process (see LED Reference Table). 3. After your camera completes the boot-up process, check for a solid Blue light. This indicates proper operation and recording. 4. Check for a Green light that remains on, indicating connectivity. 5. Watch for a Blue light. After 5 minutes, if both the Green and Blue lights don't remain on, an error has occurred. See Diagram G. TROUBLESHOOTING ERROR SCENARIOS If your KP2 has: Diagram G · Solid Red, Blue and Green lights, then a camera isn't receiving a video signal. Check your camera's connection. · A solid Blue light, but the Green light is blinking or is off, then clean and correctly reinsert your SIM card. - If the Green light still blinks, this is a configuration or server issue that requires SmartWitness support. · A Red blinking light, then there is an SD card error or corruption. Contact your local distributor or SmartWitness support to repair or replace your SD card. · A solid Red light, then your device isn't receiving enough voltage or amperage. Check the output of your power source or your ground (black wire) connection. If your KP2 install is operational, please move on to How to Calibrate Your G-Sensor. SMARTWITNESS KP2 PRO INSTALLATION GUIDE 9 HOW TO CALIBRATE YOUR G-SENSOR Park your vehicle on a flat surface for calibration. After your camera boots up, press the G-sensor calibration button. This is the small Red button to the right of the e-call/panic button. You'll hear a beep, and the KP2 LED light will blink briefly to indicate that the G-sensor calibration has registered. You've completed the first steps of your KP2 installation. To adjust your settings, continue to How to Configure KP2 Settings. SMARTWITNESS KP2 PRO INSTALLATION GUIDE 10 HOW TO CONFIGURE KP2 SETTINGS To finalize your installation and onboard your device, scan the QR code. Download and open the app. Scan your device's IMEI label, and follow the walk-through featured below. Access KP2 Installation App 1. Ensure the IMEI code in the app matches your device's IMEI. If there isn't a match, click No and contact SmartWitness support. If there's a match, click Yes to continue. 2. Read the instructions to understand more about your vehicle's "Horizon" and "Hood" lines. Click Show Me How for a brief video walk-through of the device attachment process. 3. Select your KP2 camera configuration. Choose the driver's side of the vehicle (from the perspective of the front of the vehicle). Click Next to set your vehicle's "Horizon" and "Hood" lines. 4. If you adjust either camera, click Refresh Images to update road- and driver-facing camera images. Use the arrows to adjust your vehicle's "Horizon" and "Hood" lines. Ensure your "Hood" line is in the bottom one-fourth of your image. Scroll down and click Next to save the "Horizon" and "Hood" lines. 5. Choose preferences for in-cabin alerts, an alert's volume level or activation of different ADAS and DSM events. 6. If you're unaware of a setting's function, click the info icon to learn more. Pay close attention to Camera Height. Enter an even interval value (e.g., 190 cm), not an odd interval value (e.g., 205 cm, 213 cm). 7. After you've made changes and activated the appropriate features, click Confirm to save your configuration. 8. On the home screen, you'll see a success message validating your saved configuration. Congratulations. You've configured your device settings. SMARTWITNESS KP2 PRO INSTALLATION GUIDE 11 COMPLETE YOUR INSTALLATION/SUPPORT You've finished your KP2 installation and device calibration. Your KP2 is ready to go. If you have any complications during the installation process or have any questions, please contact our support team at support@smartwitness.com or call us. North America, South America, APAC +1 (312) 981-8774 EMEA +44 (0) 1483 397005 NOT AN INSTALLER? Once you complete the training (about a 30-minute webinar), SmartWitness will provide you with login credentials for the SmartOPS portal. To schedule training, please complete the online form here. SMARTWITNESS KP2 PRO INSTALLATION GUIDE 12 LED & BUZZER SPECIFICATIONS Status/Step Warning Red LED Record Blue Communication Green SOUND Startup & Power Off Record Communication Function Warning Error Event Trigger ADAS DSM Booting Step 1 Booting Step 2 Booting Step 3 Booting Finished Power Off Power Off Finished Continuous Record Recording Event Record Standby Recording Dual Record Continuous Recording Event Recording No Record No Recording 4G LTE Network Device Ready Communication SD Format G-Sensor Calibration FW Upgrade System Warning SD Card Full Video Loss Record Error SD Error, No SD, Write Fail Communication Error 4G LTE Network Device Error, SIM Error Data Network Connection Error DMS Communication Error G-Sensor, Panic Button, Alarm-In Over Speed On On On On Off Off Off Fast On and Off On Slow On and Off - - PCW, FCW, HMW - DSW, DFW, DPUW, DDW - Off Off On and Off Off On On and Off On On Fast Simultaneous On and Off Off Off On - On - Fast On and Off - On - Fast On and Off - Off - - On - On Sequence On and Off - - Double Sequence On and Off Off - - - Off - Beep No. 2 Continuously Beep No. 2 Beep No. 2 Beep No. 3 - Beep No. 3 Off - Slow On and Off - Slow On and Off - - Beep No. 1 - - Beep No. 4 (2 Times) - - Warning Beep or Voice - - Warning Beep or Voice SMARTWITNESS KP2 PRO INSTALLATION GUIDE 13 TECHNICAL SPECIFICATIONS NAME Image Sensor Angle of View Wireless Connectivity Max Data Rate Video Resolution Recording Speed Recording Mode Memory GPS/GNSS G-Sensor VALUE 2 Megapixel CMOS Sensor Main, Road-Facing Camera (Forward-Facing): 140° (115°(H), 60°(V)) 2nd Camera (Optional, Driver-Facing): 130° (104°(H) x 56°(V)) LTE CAT6 (KP2-NA): B2/B4/B5/B7/B12/B13/ B14/B17/B25/B26/B41/B66/B71 LTE CAT6 (KP2-GB): B1/B2/B3/B4/B5/B7/B8/ B20/B28/B38/B40/B41 3G (KP2-GB): B1/B2/B4/B5/B8 Wi-Fi: 2.4/5GHz, 802.11 a/b/g/n/ac Bluetooth: 4.2 BLE 4G/LTE (CAT6) UL: 50Mbps, DL: 300Mbps Main Camera: 1080p (1920 x 1080), 720p (1280 x 720) 2nd Camera: 1080p (1920 x 1080), 720p (1280 x 720) 60FPS (30FPS per Channel) Continuous, Event, Dual Mode 16GB eMMC + 2GB LPDDR3, MicroSD Card Support up to 256GB (FAT32) Internal GPS/GLONASS/BeiDou Internal 3-Axis G-Sensor NAME VALUE Gyro Time Speaker Audio 3 Axis (X, Y, Z), Output Rate: 100Hz GPS Time Sync + Built-In Real-Time Clock (RTC) Audible Alerts for Events and Audio for ADAS and DSM. Natural Language or Beep Sounds (Selectable) Internal Microphone Serial RS232 RX/TX LED Supercapacitor PC Software 3 (Red, Blue, Green LED) Enables Recording of Last File and Safe Shutdown MSM8953, Octa-Core ARM Cortex-A53 Power Input Input Voltage: DC 12V/24V, 1.5A Delayed Power Shutdown Power Consumption Size/Weight Supports Delayed Power Shutdown and Automated Wake-Up Feature (Selectable Intervals) 4W (6W With ADAS and DSM Enabled) 126 x 82 x 64 mm/232.4g (Including 2nd Camera, Excluding Power Cable) Operational Temp. -10°C~55°C Storage Temp. Certification/ Regulatory Warranty -20°C~70°C FCC, CE, E-Mark, UKCA, RoHS, IC, PTCRB, RCM, AT&T, Verizon and FirstNet 2-Year Standard SMARTWITNESS KP2 PRO INSTALLATION GUIDE 14 © 2022 SmartWitness. All Rights Reserved. smw3016-NA_0622