E6 Connect Manual - E6Golf
E6 Golf PortalE6 Golf Portal
User Manual for SLX models including: SLXMN200, SLX-NANO 2.0, SLX-NANO X3, NANO 2.0 Dual Motion Sensor for Glove, NANO 2.0, Dual Motion Sensor for Glove, NANO 2.0 Motion Sensor, Motion Sensor, Sensor
Ulike Co., Ltd. SLXMN200 2AHUGSLXMN200 2AHUGSLXMN200 slxmn200
File Info : application/pdf, 18 Pages, 1.40MB
DocumentDocumentUser Manual Copyright 2023. Lab-T, Inc. TITLE SLX-NANO USER MANUAL 3 PRO Dual motion sensor for glove (NANO 2.0) SLX-NANO X3 USER MANUAL User Manual 1 Composition SLX-NANO USER MANUAL SLX-NANO 2.0 (Multi Motion Sensor) 2.0 model components. It may be changed depending on some package keys. NANO SENSOR Nano Glove Mount Charger Cable SLX-NANO X3 USER MANUAL 2 Register Product SLX-NANO USER MANUAL Welcome to SLX. Register your product right away. After registration, you will receive an E6 Connect license. Register Card Scan QR with Camera App You must register your product and serial number on SwingLogic.us and select the license type to receive your E6 License key Registration STEPS Or navigate to https://register.swinglogic.us Use Camera app to scan included QR code Fill out registration information. E6 license key will be emailed from registration@swinglogic.us and is accessible from the SwingLogic user portal Set up E6 account at https://portal.e6golf.com/ using the same email address in step 2 Redeem license key Download E6 Connect and setup using the same email address as above Caution ) If you do not register the product, you will not be able to receive a license, and some AS and exchange may be difficult. SLX-NANO X3 USER MANUAL 3 Swing with Nano sensor SLX-NANO USER MANUAL If you use a nano sensor, you can get more accurate swing results. Golf gloves are required when swinging using the nano sensor. Mount the sensor as shown in the figure below and install it vertically in the correct position to increase the accuracy. If you use nano sensor, you can get more accurate swing results. For accurate use, install it as shown in the figure below. 1 Insert the glove with the hook facing up as shown in the picture. 2 Insert the NANO sensor into the mount, turn it exactly 90 degrees clockwise (USB direction is down) 3 Be well leveled in the setup position 4 Swing within 3 seconds of vibration 5 Raise your wrist up to control the club Note) Swing recognition may be difficult depending on the golfer's setup posture. In this case, adjust the position of your nano sensor to find the recognized position. SLX-NANO X3 USER MANUAL 4 Charging and using Power bank SLX-NANO USER MANUAL Charge your phone during a round of golf with power bank function Device Charging Adapter is not included Nano 5V Caution) It can be charged with USB-C type using a 5 V d.c., 1 A charging adapter. Hybrid charging time 8 hours, Nano charging time 2 hours SLX-NANO X3 USER MANUAL 5 Button and LED Guide SLX-NANO USER MANUAL Enjoy the ultra-easy-to-operate buttons and the Nano button with remote control function. Nano Button Club / Volume UP/DOWN button Power (Push 3sec) / Display Mode Button Nano LED Bluetooth Connected Swing Ready Club Change Swing Result SLX-NANO X3 USER MANUAL 6 Firmware Update SLX-NANO USER MANUAL Connect SLX-CONNECT > Connect menu > Device Select When the firmware of HW is updated, it is activated with a green button. SLX-NANO X3 USER MANUAL 7 Device Factory Reset SLX-NANO USER MANUAL If device is not connected continuously, any button does not work, or is incorrect, you can perform a factory reset through the button. Press two fingers at the same time the + / - button continuously for more than 7 seconds. Nano Caution) All stored calibration data will be deleted during factory reset. SLX-NANO X3 USER MANUAL 8 Using E6 Connect SLX-NANO USER MANUAL E6 CONNECT software is available. Please install and connect according to each SETP. Create an account and register with Swing Logic STEP 1 Create an account and register with us STEP 1 Find the included Card as depicted below: You can either scan the QR code on your phone's camera or go to : https://register.swinglogic.us LICENSE OPTIONS EXPLAINED (IMPORTAN) 5-Course Option is your FREE License and one version ( iOS or PC) is included with Purchase. If you want to UPGRADE to the Expanded Content Subscription @ $10/mo, that is the and Option DETAILS: Expanded Content Subscription now has ~40 Courses, mini games ( darts, closest to pin, battleship...) & Online Play + multiple modes ( Regular Stroke Play, captains choice, best ball etc...) Check out our website to learn more about the additional features if this interests you. If you are an avid golfer...$10/mo for infinite rounds on 40 courses is a pretty good deal SLX-NANO X3 USER MANUAL 9 Using E6 Connect SLX-NANO USER MANUAL Install E6 CONNEC STEP 2 After download, Run the program to install the software. PC Version: https://portal.e6golf.com/update/e6-connect iOS Version: You will need to download the software from the app store. If you search for "E6 CONNECT" then it will pull up and you will be able to download Start the E6 Application & Redeem your License STEP 3 If you have a License code, press the REDEEM button to enter the code. If you don't have the code, press SKIP to move on. If you press SKIP, the demo version will be applied by default. You will also be required to setup an E6 Connect Account during this process. Please take note and remember your login credentials SLX-NANO X3 USER MANUAL 10 Using E6 Connect License Activation Enter License Key and press the Enter button SLX-NANO USER MANUAL STEP 4 Select Tracking System Device Select "SwingLogic -SLX " STEP 5 NOTE : Depending on the license type you are redeeming, the list of available trackers will be different. If you have redeemed any of the license we have provided, the list will be much shorter and contain only small sensor based products SLX-NANO X3 USER MANUAL 11 Using E6 Connect SLX-NANO USER MANUAL Calibrate sensor Setting - Maximize Accuracy STEP 8 When inside the application's Main Menu. Se ngsSimulatorConfigure Important! Default Settings should be: Difficulty = Normal, Sensitivity = Normal, Woods/Iron/Putter = Your Choice based on type of clubs you will be installing sensor on. It is best to start with 0% distance "boost" to see what your sensor is displaying initially then adjusting up or down based on simulator output vs expected ball flight. You can also increase the altitude in Enviromental Settings to have your ball fly further Check the swing data on the screen STEP 9 When you swing, the ball will fly on the screen and Post-Shot dialog is displayed. Important! For more details on E6 Connect, check the "https://e6golf.com/e6-connect/manual" SLX-NANO X3 USER MANUAL 12 Using E6 Connect SLX-NANO USER MANUAL Club selection control STEP 10 You can change your club selection outside of the E6 Connect Application by click these up and down buttons Important! On the green, it automatically changes to the target direction. (Club side does not work on green) Target Control STEP 11 In the fairway / driving range, if you click the mode button once, it will change to "Target Control mode". Afterwards, you can change the target with the up/donw buttons. If you click the mode button again, it will change to "Club Control mede". SLX-NANO X3 USER MANUAL 13 Troubleshooting SLX-NANO USER MANUAL Check the latest registered information at swinglogic.us/support. Below is a simple troubleshooting guide. Replacing and reconnecting the Nano Sensor If the Hybrid and Nano are not connected or if you need to replace the Nano, See the "Nano Sensor Replacement" manual. If you press and hold the "-" button on the Hybrid and Nano sensors, they are automatically connected. . Nano Sensor Swing Recognition If the nano sensor does not recognize the swing well, try adjusting the position of the sensor installed on the glove. Depending on the customer's setup posture, it may not be recognized. . Calibration of swing results If the swing results are very different try adjusting each result in the SLX-Connect app > Settings > Calibration menu. Factory reset If everything does not work, you can reset it by pressing the "+" / "-" buttons at the same time for 7 seconds. Read the "Factory Reset" menu. SLX-NANO X3 USER MANUAL 14 FCC / IC RULES SLX-NANO USER MANUAL FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. RF Exposure Statement Sample wording: This equipment complies with FCC RF exposure requirements set for th in an uncontrolled environment and can be used without any restriction. Industry Canada Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1)this device may not cause interference, and (2)this device must accept any interference, including interference that may cause undesired operation of the device. SLX-NANO X3 USER MANUAL 15 FCC / IC RULES SLX-NANO USER MANUAL Énoncé d'Industrie Canada(IC) Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. Tout changement ou modification non expressément approuvé par la partie chargée de la mise en conformité peut annuler le droit de l'utilisateur à utiliser l'équipement. Déclaration d'exposition aux RF Exemple de formulation: Cetéquipementestconforme aux exigences d'exposition RF d e la FCC énoncées dans un environnement non contrôlé et peutêtreutilisé sans aucun e restriction. SLX-NANO X3 USER MANUAL 16 SLX-NANO USER MANUAL NANO NANO SPECIFICATION Product name : Dual motion sensor for glove (NANO 2.0) Model No : SLX-MN200 Size : 35mm * 35 mm (12g) Bluetooth : 4.0 BLE 2.43GPhRzO1Mbps Power Source : Li-Polymer 80mAh Operating Temperature: -10 °C ~ 50 °C Storage temperature: 5 °C ~ 40 °C Manufacturer: ULIKE (MADE IN KOREA) Address : 23, Daehak 1-ro 58beon-gil, Yeongtong-gu, Suwon-si, Gyeonggi-do, Republic of Korea ULIKE Co,Ltd 17