User Manual for MIBOXER models including: D1-CX, D2-CX, D3-CX, D4-CX, D5-CX, Constant Voltage DMX512 RDM Decoder
Features. 1. Accord with DMX512 standard protocol. 2. Digital Display, Set DMX initial address through button. 3. Support RDM function. 4. 2000hz/500hz Output PWM frequency is optional.
M INPUT OUTPUT CH1 M INPUT OUTPUT CH1 CH2 M INPUT OUTPUT CH1 CH2 CH3 M INPUT OUTPUT CH1 CH2 CH3 CH4 M INPUT OUTPUT CH1 CH2 CH3 CH4 CH5 4. Restore factory default. Under unlock status, long press M buttom 10 seconds until digital display show . Logarithmic dimming curve Linear dimming curve
Subordinate New Brand Constant Voltage DMX512 & RDM Decoder Model No.: D1-CX / D2-CX / D3-CX / D4-CX / D5-CX 130mm Features 1. Accord with DMX512 standard protocol. 2. Digital Display, Set DMX initial address through button. 3. Support RDM function. 4. 2000hz/500hz Output PWM frequency is optional. 5. Logarithm/Linear dimming curve is optional. 6. Anti-reverse protection function 7. Short circuit&Overcurrent protection and recover function. 8. self-testing protection function when power on. Parameter 49mm 27mm Model No. Output D1-CX 20A/Channel D2-CX 10A/Channel D3-CX 6A/Channel D4-CX 5A/Channel D5-CX 4A/Channel Total Output Max 20A Max 18A Max 20A Input Voltage DC12~24V Input Signal DMX512, RDM Connection Common anode Working Temp. -20~60°C Function Settings 1.Digital Display status description Self-locking: Get into locking state when there is no operation over 30 seconds, digital display with low light or OFF. Unlock: Long press M button 2 seconds to make digital display with high light, quit self-locking state. Address always ON: DMX signal valid. Address flickering: DMX signal invaild. Err: Short circuit/overcurrent protection; self-recover after 10 seconds. 2. DMX initial address setting Under unlock status, when digital display show 001-512( for example ), Short press · button or buttom, you can change the DMX initial address; Long press, you can change it quickly. For Example: Set Initial address to 100 D1-CX D2-CX D3-CX D4-CX D5-CX Occupy 1 address 100 Occupy 2 address Occupy 3 address Occupy 4 address 100-101 100-102 100-103 Occupy 5 address 100-104 3. System Parameter Setting Instruction Under unlock status: Long press M button 3 seconds to make digital display show or , then get into system parameter setting. By this time, short press M button to switch 4 different parameter setting circularly. Parameter 1: PWM frequency setting(show or ; Short press · button or button to switch. Set to PWM high frequency output, 2000Hz. (Factory default parameter) Set to PWM low frequency output,500Hz. Parameter 2: Dimming Curve setting(Show or ), short press · button or button to switch. Dimming curve is logarithm dimming. (Factory default parameter) Dimming curve is linear dimming. Parameter 3: Dimming smoothness setting(show or ), short press · button or button to switch. Smooth dimming. (Factory defaut setting) Standard dimming. Parameter 4: Digital display showing setting(show or ) short press · button or button to switch. Under self-locking status, digital display always ON (low lighting showing). (Factory default parameter) Under self-locking status, digital display OFF. Exit system mode: long press M button 1 second to exit. Or it will be self exit if there is no operation over 8 seconds. 4. Restore factory default. Under unlock status, long press M buttom 10 seconds until digital display show . PWM duty(%) PWM duty(%) Dimming curve diagram Logarithmic dimming curve 100 Gamma=1.6 90 80 70 60 50 40 30 20 10 10 20 30 40 50 60 70 80 90 100 Brightness(%) Linear dimming curve 100 Gamma=1.0 90 80 70 60 50 40 30 20 10 10 20 30 40 50 60 70 80 90 100 Brightness(%) Connection diagram DMX512 Console DMX512 Dimming Panel D1-CX D2-CX D3-CX D4-CX D5-CX M W B G RGBW LED Strip R v+ M M W C Color Temp. LED Strip v+ M v- Brightness LED Strip v+ M INPUT OUTPUT CH1 INPUT OUTPUT CH1 CH2 INPUT OUTPUT CH1 CH2 CH3 INPUT OUTPUT CH1 CH2 CH3 CH4 INPUT OUTPUT CH1 CH2 CH3 CH4 CH5 V- V+ Power input DC12V/24V V- V+ Power input DC12V/24V V- V+ Power input DC12V/24V V- V+ Power input DC12V/24V V- V+ Power input DC12V/24V W C B G R v+ B G R v+ RGB+CCT LED Strip RGB LED Strip Attention: 1. If the decoder is over 32pcs, or using the super long signal cable, you need DMX signal amplifier. Amplify signal cannot be over 5 times. 2. If there is overshoot effect due to the long signal cable or low quality circuit, please connect 0.25W 90-120 terminal resistance at the end of each DMX sigbal cable. Attention 1. This product should be debugged and installed by professionals. 2. Please check whether the output voltage of the power supply meets the requirements of the product voltage range. 3. The product is not waterproof, please install it in the waterproof box when installed outdoors. 4. Before switching on the power, please ensure that all wiring is correct, so as not to cause damage to the devicesb 5. If fault has occurred non-professionals do not repair it without permission, otherwise the devices will be damaged. DMX RDM Made in ChinaAdobe PDF library 15.00 Adobe Illustrator CC 22.1 (Windows)