ASUS ZenWiFi BT10 Quick Start Guide

Introduction

This guide provides quick start instructions for the ASUS ZenWiFi BT10 Tri-Band Wi-Fi Router. It covers hardware explanations, installation, AiMesh setup, and troubleshooting.

* If no 6GHz SSID appears, please check if your operating system and client device are licensed to support the new 6GHz band. You can check Wi-Fi 6E driver availability with your operating system and client device provider.

Hardware Overview

Connect the power adapter to the DCIN power input port and press the power button [power button]. The LED indicator light [LED indicator] will turn on when the hardware is ready.

ZenWiFi BT10 Description

Ports:

• USB 3.0 Port [USB port]
• 10G WAN/LAN2 Port
• DCIN Power Port
• LED Indicator
• WAN/LAN1 Port
• 10G LAN3 Port
• Power Switch

Port Connections:

• WAN/LAN1 Port, 10G WAN/LAN2 Port: Connect your optical modem to the WAN/LAN1 port or the 10G WAN/LAN2 port with a network cable.
• 10G LAN3 Port: Connect your PC to a LAN port with a network cable.

Specifications

* The USB port is available for LTE (UE) USB dongles.

AiMesh WiFi System Setup

Preparation

1. Get two ZenWiFi BT10 units and power them on.
2. Use a network cable to connect your optical modem to the WAN/LAN1 port or the 10G WAN/LAN2 port of the ZenWiFi BT10 labeled "Main Unit". This ZenWiFi BT10 will be the AiMesh router, and the other ZenWiFi BT10 will be the AiMesh node.
3. The LED light turns solid blue to indicate that the ZenWiFi BT10 is ready for configuration.

ASUS Router App

Download the free ASUS Router App to configure and control your router(s).

[Download on the App Store] [Get it on Google Play]

Setup Steps

1. Preparation: Place the AiMesh router and node in the same room and at least 1 meter apart during the setup process.
2. AiMesh Node: Keep the AiMesh node powered on and ready for AiMesh system configuration.
3. Start ASUS Router App: Open the ASUS Router App and follow the on-screen instructions to complete the AiMesh setup.

NOTE: When using a wireless backhaul to connect your router and AiMesh node, the WAN/LAN ports on your AiMesh node can be used as LAN ports.

Troubleshooting

If the AiMesh router cannot find any nearby AiMesh nodes or synchronization fails, check the following and try again:

• a. Move the node closer to the AiMesh router if possible. Ensure it is within 3 meters.
• b. Verify that the AiMesh node is powered on.

Placement for Optimal Performance

Place the router and AiMesh node in the best possible location.

NOTES: To minimize interference, keep routers away from devices like cordless phones, Bluetooth devices, and microwave ovens. It is recommended to place routers in an open or spacious area.

LED Indicators

ZenWiFi BT10 LED Indicators:

• Solid Blue: The ZenWiFi BT10 is ready for configuration.
• Solid White: The ZenWiFi BT10 is connected and functioning correctly.
• Solid Yellow: The signal between your ZenWiFi BT10 router and the node is weak.
• Solid Red: The ZenWiFi BT10 has no Internet connection. / The node is disconnected from the router.

Frequently Asked Questions

Q1: Does the AiMesh router support Access Point mode?

A: Yes. You can choose to configure the AiMesh router in router mode or access point mode. Access the graphical user interface (http://asusrouter.com) and select Administration > Operation Mode.

Q2: Can a wired connection be established between AiMesh routers (Ethernet backhaul)?

A: Yes. The AiMesh system supports both wireless and cable connections between the AiMesh router and node to maximize performance and stability. AiMesh analyzes the wireless signal strength for each available frequency band and then automatically determines whether a wireless or wired connection is best to serve as the central link between routers.

1. First, follow the setup steps to establish a connection between the AiMesh router and the node via WiFi.
2. Place the node in the ideal location for best coverage. Run an Ethernet cable from the AiMesh router's LAN port to the AiMesh node's WAN port.
3. The AiMesh system will automatically select the best route for data transmission, whether wired or wireless.

Q3: Where can I find more information about the Mesh WiFi system?

A: Technical Support Website: https://www.asus.com/support

Video Tutorials: https://qr.asus.com/wl_videotutorials

Support and Resources

For technical service and support, please visit the ASUS support website or view video tutorials.

• Technical Support: https://www.asus.com/support
• Video Tutorials: https://qr.asus.com/wl_videotutorials

Compliance and Safety Information

ASUS Recycling/Takeback Services

ASUS recycling and takeback programs are part of our commitment to protecting the environment. We provide solutions for responsibly recycling our products, batteries, other components, and packaging materials. For detailed recycling information in different regions, please visit http://csr.asus.com/english/Takeback.htm.

REACH

In compliance with the REACH (Registration, Evaluation, Authorisation, and Restriction of Chemicals) regulatory framework, chemical substances in our products are published on the ASUS REACH website at http://csr.asus.com/english/REACH.htm.

Federal Communications Commission (FCC) Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.

FCC regulations restrict the operation of this device to indoor use only. The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft. Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with unmanned aircraft systems.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WARNING!

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Prohibition of Co-location

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

IMPORTANT NOTE: Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC exposure compliance requirements, please follow the operation instructions as documented in this manual.

WARNING!

This equipment must be installed and operated in accordance with provided instructions, and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 59 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Safety Notices

• Use this product in environments with ambient temperatures between 0°C (32°F) and 40°C (104°F).
• Refer to the rating label on the bottom of your product and ensure your power adapter complies with this rating.
• DO NOT place on uneven or unstable work surfaces. Seek servicing if the casing has been damaged.
• DO NOT place or drop objects on top and do not shove any foreign objects into the product.
• DO NOT expose to or use near liquids, rain, or moisture. DO NOT use the modem during electrical storms.
• DO NOT cover the vents on the product to prevent the system from getting overheated.
• DO NOT use damaged power cords, accessories, or other peripherals.
• If the Adapter is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.
• To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system.
• DO NOT mount this equipment higher than 2 meters.

Compliance Statement of Innovation, Science and Economic Development Canada (ISED)

This device complies with Innovation, Science and Economic Development Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. CAN ICES-003(B)/NMB-003(B)

Radio Frequency (RF) Exposure Information

The radiated output power of the ASUS Wireless Device is below the Innovation, Science and Economic Development Canada radio frequency exposure limits. The ASUS Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized.

This equipment should be installed and operated with a minimum distance of 66 cm between the radiator and any part of your body.

This device has been certified for use in Canada. Status of the listing in the Innovation, Science and Economic Development Canada's REL (Radio Equipment List) can be found at the following web address: http://www.ic.gc.ca/eic/site/ceb-bhst.nsf/eng/h_tt00020.html

Additional Canadian information on RF exposure also can be found at the following web: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html

For product available in the US/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.

This device is restricted for indoor use only.

Devices shall not be used for control of or communications with unmanned aircraft systems.

Operation on oil platforms, automobiles, trains, maritime vessels and aircraft shall be prohibited except for on large aircraft flying above 3,048 m (10,000 ft).