User Manual for Galaxy Equipment models including: 177GMIX30 Planetary Mixers, 177GMIX30, Planetary Mixers, 177GMIX30 Mixers, Mixers
10 hours ago — User Manual. Planetary Mixers. User's Manual. - 1 -. Please read the manual thoroughly prior to equipment set-up, operation, and maintenance. 177GMIX30.
User Manual. Planetary Mixers. User's Manual. - 1 -. Please read the manual thoroughly prior to equipment set-up, operation, and maintenance. 177GMIX30.
User Manual Planetary Mixers User's Manual 177GMIX30 8/2021 Please read the manual thoroughly prior to equipment set-up, operation, and maintenance. - 1 - User Manual Index Parts Overview ............................................................... 3 Standard Accessories.................................................... 4 Operation Instructions................................................... 4 Mixer Capacity Chart ..................................................... 5 Troubleshooting ............................................................. 6 Circuit Diagram .............................................................. 6 Figure 1 Axle Diagram ................................................... 7 Figure 2 Gear Axle Diagram .......................................... 8 Figure 3 Gear Axle I Diagram ........................................ 9 Figure 4 Turning Plate & Mixing Axle Diagram........... 10 Figure 5 Lifting Unit ..................................................... 11 Figure 6 Fork & Speed Shaft ....................................... 12 Warranty Information ................................................... 13 - 2 - User Manual Parts Overview ITEM DESCRIPTION # 1 Screw M6*45 1 2 Top Cover 1 3 Two Axle Cover 1 4 Center Axle Cover 1 5 Screw M8*25 8 6 Ring 4 7 Bearing Cover 1 8 Body 1 9 Spiral 1 10 Bearing 6205 2 11 Motor Rotor 1 12 Stator of Motor 1 13 Motor Switch-A 1 14 Motor Switch-B 1 15 Rear Bearing Cover 1 16 Fan 1 17 Rear Cover 1 18 Screw M6*45 4 19 Stand 1 20 Bowl's Board 2 21 Arm 1 22 Cable Joint 1 23 Cover 1 24 Screw M6*12 4 25 Seat 1 - 3 - User Manual Standard Accessories Item Description Qty 1 Flat Beater 1 2 Dough Hook 1 3 Whisk 1 4 Bowl 1 NOTES: · Any agitator is easily installed by simply raising it onto the mixing axle, and the rotating it clockwise on the shaft until it locks into place. To remove, raise the agitator on the shaft until it clears the lock and then rotate counter-clockwise and lower. · All of the accessories are precisely fitted to the bowl, have rounded corners, and are easily removable for cleaning. · DO NOT hose down mixer. · DO NOT operate mixer with wet hands. · ALWAYS unplug mixer from electrical supply prior to any maintenance or repairs. Operation Instructions ! Please ensure that your power supply matches your machine ! For changing the speed: Please stop machine first before changing speed in order to avoid damage to the gear box. Also make sure that the bowl is in fully lifted position and the guard is closed. · Slow Speed is the middle, #1 setting. The knob will be facing forward. · Medium Speed is the bottom, #2 setting. The knob will be straight down. · High Speed is the top, #3 setting. The knob will be straight up. Mixing: Always use the correct attachment for the job. A. Whisk: Suitable for mixing liquids and soft ingredients, can work in all speeds. Do not run for more than 15 minutes. B. Flat Beater: Suitable for mixing dry ingredients, can work in low & medium speeds only. Do not use in high speed. Do not run for more than 15 minutes. C. Dough Hook: Suitable for mixing dough, can work in low & medium speeds only. Do not use in high speed, do not run for more than 20 minutes. Absorption ratio must be more than 50%. Refer to mixer capacity chart. - 4 - User Manual Mixer Capacity Chart Product Bread and Roll Dough - 60 % AR Heavy Bread Dough - 55% AR Pizza Dough, Thin - 40% AR Pizza Dough, Medium - 50% AR Pizza Dough, Thick - 60% AR Raised Donut Dough - 65% AR Mashed Potatoes Waffle or Hot Cake Batter Egg Whites Whipped Cream Cake Batter Agitator and Speed Dough Hook - 1st only Dough Hook - 1st only Not Recommended Not Recommended Not Recommended Dough Hook - 1st and 2nd Flat Beater Flat Beater Wire Whisk Wire Whisk Flat Beater Maximum Bowl Capacity 10 Qt. / 20 Qt. 5 lb. / 20 lb. 3 lb. / 15 lb. 2 lb. / 8 lb. 5 lb. / 12.5 lb. 4 Qt. / 8 Qt. 1 Qt. / 1 Qt. 1 Qt. / 2 Qt. 8 lb. / 20 lb. When mixing dough ( pizza, bread, or bagels), check your "AR" absorption ratio - water weight divided by flour weight. Above capacities based on 12% flour moisture at 70°F water temperature. If high gluten flour is used, reduce above dough batch size by 10%. Example: If recipe calls for 5 lb. of water and 10 lb. of flour, then 5 divided by 10 = 0.50 x 100 = 50% AR. · 2nd Speed should never be used on mixtures with less than 50% AR. · Do not use attachments on hub while mixing. When calculating the correct size mixer for your application, here are some helpful weights and measures: · 8.3 lb. = 1 gallon of water 2.08 lb. = 1 Quart. - 5 - User Manual Troubleshooting Trouble The axles can't work when operating the machine The mixing bowl is out of position Possible Causes Poor contact of the electrical equipment Moving direction is not correct Solution Check the Plug Change Leaks oil Difficult to move the bowl up and down The motor is overheated and speed is down Noise and overheating Mixer touches bowl Sealing washer is damaged Change Slideway is rusted Clean the slideway and lubricate The voltage is not enough, or incorrect speed Check the voltage or use lower speed Poor lubrication Add or change lubrication The mixing device or bowl deformed Repair or change the bowl or mixing device Circuit Diagram ITEM DESCRIPTION K0 Electromagnetic Switch K1 Safety Covering Switch K2 Fluctuate Safety Switch K3 Overload Protection Switch K Switch C Capicitor M Motor - 6 - User Manual Axle Diagram ITEM DESCRIPTION # 1 Baffle 1 2 Roller 6 3 Spring 6 4 Engager 1 5 Gear Ring 1 6 Dividing Ring 1 7 Joint Gear 1 8 Bearing Ring 1 9 Joint 1 10 Bearing Ring 1 11 Joint Gear 1 1 12 Ring 1 13 Bearing (6206) 1 14 Oil Seal (Pd45*52*10) 1 15 Sleeve 1 16 Axle 1 17 Key 1 18 Key 2 19 Key 1 20 Bearing (6205) 1 NOTES: · Be sure to install in correct position (see Figure 2-1) and lubricate all of the pins in the sleeve drive when assembling. · Joint (9) must always be raised and lowered smoothly. Be sure joint sleeve is positioned as showin in Figure 2-2. · Check Oil Seal (14) if oil leaks from drip cup. - 7 - User Manual Gear Axle Diagram ITEM DESCRIPTION # 1 Bearing (6203) 1 2 Gear Axle 1 3 Key 2 4 Sleeve 1 5 High Speed Gear 1 6 Low Speed Gear 1 7 Bearing 6203 1 8 Plate 1 NOTES: · At the center in the shaft unit. To the above is the gear shaft and gear shaft I. (see Figure 3-1) · C-type stop ring (6/8) has to be fixed when reassembling. · Be sure that the keys are inserted - 8 - User Manual Gear Axle I ITEM DESCRIPTION # 1 Bearing (6201) 1 2 Gear Axle 1 3 Key (5*14) 1 4 Gear 1 5 Stop Ring 1 6 Bearing (6201) 1 NOTES: · C-type stop ring (5) has to be fixed when reassembling - 9 - User Manual Turning Plate & Mixing Axle Diagram ITEM DESCRIPTION # 1 Screw (M6*35) 6 2 Turning Plate 1 3 Ring 1 4 Nut 1 5-1 Safety Net (Locomotion) 1 5-2 Safety Net (Immobility) 1 6 Inner Gear 1 7 Screw 1 8 Planetary Gear 1 9 Bearing (6204) 1 10 Bearing (6206) 1 11 Oil Seal (Pd35*56*12) 1 12 Key 1 13 Mixing Axle 1 14 Pin 1 - 10 - User Manual Lifting Unit ITEM DESCRIPTION # 1 Arm 1 2 Bowl's Screw 2 3 Ring 2 4 Nut 2 5 Scew M5*12 4 6 Gasket 4 7 Arm's Upper Board 1 8 Guide Post Plate 1 9 Scew M8*20 8 10 Flat Plate 2 11 Gasket 6 12 Screw M8*20 6 13 Arm's Lower Board 1 14 Plastic Ball 1 15 Handle 1 16 Flange Sleeve 1 17 Handle Crank 1 18 Small Shaft of Pull Rod 1 19 Pull Rod 1 20 Screw M12*45 1 21 Handle Hanging Shaft 1 - 11 - User Manual Fork & Speed Shaft ITEM DESCRIPTION # 1 Axle 1 2 Nut 1 A 3 Spring 4 Shaft 1 1 5 Fork 1 6 Pin 1 7 Eccentricity Knot 1 8 Steel Ball 1 B 9 Speed Spring 1 10 Speed Block 1 11 Screw 1 12 Shaft 1 13 Handle 1 NOTES: · The speed selector/shifting mechanism is designed for simplicity and reliability. It features three mixing speeds. · Speed selection is made by aligning the pointer of the shifter handle with the proper number on the shift selector. Stop the mixer before making any speed changes. · Apply sealant to the shift selector assembly and install it. - 12 -Adobe PDF Library 15.0 Adobe InDesign 16.0 (Macintosh)