Manuals+
AutoConnect AC200GPS3G Quick Install Guide

AutoConnect AC200GPS3G Quick Install Guide

Model: AC200GPS3G

Manufacturer: AutoConnect

Quick Start Guide

Thank-you for your purchase! You've made the decision to have full control of your vehicle. Follow the steps below to begin a new era of vehicle controls.

  1. Ensure you have the Serial # for your device.
  2. Visit our website and click on the “Activate” tab, and fully complete form. Once submitted you will receive a confirmation email from Northsat Distribution with the details of your device activation.
  3. Select YOUR model number (device type) and fully complete form.

Support: 1 855 287 4477 | autoconnectgps.com

Take Control of Your Vehicles Like Never Before!

On All Three Major Platforms

Installer Portal

1. Determine Installation Type

When installing an Autoconnect device you must first determine the installation type. The following pages will help you determine the type and instructions for installation.

2. Install Your Autoconnect GPS Modem

  • Choose proper installation location ensuring to follow instructions on install guide.
  • Determine with customer if installation is to be stealth (not visible).
  • Have label facing the sky and clear from any metal above it.
  • Actual location will vary by vehicle year, make and model.

TIP: WE RECOMMEND AFFIXING THE SID STICKER TO THE DOOR JAMB OF THE VEHICLE

3. Test the Device Functions

TIP: Choose the proper IC3 Protocol if applicable before sending any test commands.

  • Click on the Customer Log-in ?️ icon at the top of any page of the autoconnectgps.com website or download the free App for your mobile device.
  • Each Device comes with "TEST DATA" for you to test all functions. This data will expire a few days after installation.
  • Use the SID# for USERNAME and PASSWORD.
Image depicts a login screen with fields for 'Username' and 'Password', and a 'Login' button.

AC200GPS3G Quick Install Guide

Attention: This modem is shipped temporarily pre-activated for the installer to send up to 50 test commands before having to send in the activation form.

STEP 1: Determine Installation Type and Options

Depending upon your requirements, the AC200GPS3G module can be installed in a variety of ways.

  • Type 1 - Standalone GPS Tracking
  • Type 2 - Solace / Titan Elite Remote Starter
  • Type 3 - Fortin EVO-ALL (Standalone FW)
  • Type 4 - Fortin EVO-ONE
  • Type 5 - ADS AL-CA (Standalone FW)
  • Type 6 - ADS iDatastart (Classic, BM&BZ, VWx, HCx)
  • Type 7 - Compustar (CM6x00 & CM7x00 Series)
  • Type 8 - DEI (DBALL2/3, 4x10 / 5x10)
  • Type 9 - DEI (REMOTE STARTERS with ESP2)

STEP 2: Complete the wire connections according to the selected Installation Type.

Please see the following pages for detailed instructions and wiring diagrams.

STEP 3: Position the AC200GPS3G Module in an Optimal Location

Failure to adhere to these suggestions will result in a weak cellular and/or GPS signal and will affect the performance of the device.

  • Secure in upper portion of dash in a hidden location with correct side pointing skyward.(label will indicate proper orientation)
  • Do not cover with metal or position near any source of interference (Vehicle Radio, BCM). Keep a safe distance of at least 24”.

STEP 4: Confirm LED Status

LED Status Description
Blue 2 Flashes / Second Connected / Online
Green 1 Flash / Second Valid GPS

STEP 5: Confirm Vehicle Connectivity and GPS location

Each AC200GPS3G device is shipped pre-activated for the installer to send up to 50 test commands before having to complete the online activation form. It is HIGHLY recommended that you follow one of the test procedures below to ensure proper functionality. Alternatively you can call Certified Tracking Solutions and we will perform the test with you.

For Live Tech Support:

Call Certified Tracking Solutions at 1-780-391-3800.
Toll Free 1-855-287-4477(CTS-4GPS)
Monday to Friday 8AM to 5PM MST
AutoConnectGPS.com

Test Procedure

1) Login to view and test the AC200 device

A: via the AutoConnect website

  1. Go to www.AutoconnectGPS.com and click on "Customer Login".
  2. Enter the AC200GPS3G's Serial# (ESN) for both the User Name and password.
  3. Click Login.
Image shows the AutoConnect website login page with fields for Username and Password, and a Login button. The AutoConnect website dashboard should load and display the Serial number of the AC200GPS3G device that you are installing.

B: via the AutoConnect Smartphone App

  1. Download the AutoConnect Smartphone app by searching “Autoconnect GPS" for iPhone, Android or Blackberry.
  2. Open App and click on “Config" then "Login".
  3. Enter the AC200GPS3G's Serial# (ESN) for both the User Name and password.
  4. Click “Save”.
Image shows the AutoConnect app configuration screen with a 'Login' option, and a 'Save' button on an account login screen.

2) Test Vehicle GPS Connectivity

A: via the AutoConnect website

The successful completion of this section will enable you to see the current position of the AC200GPS3G device on the dashboard/Smartphone map.

  1. Click on device serial # on the left side of the screen. The asset info box will open on the bottom left corner of the screen.
  2. Click on the “Asset Commands & Controls" icon located at the top of the Asset Info box.
Image shows an 'Asset Info' box with details like Serial #, Status, Last Comms, Last GPS, GPS status (Valid, 8 Sats), Location, etc.

B: via the AutoConnect Smartphone App

  1. Click on the “GPS” tab.
  2. Click on the “Bullseye” button at top left of screen.
Image shows the smartphone app interface with a 'GPS' tab selected and a 'Bullseye' icon in the top left corner. Other icons like 'Theft 15' and 'Webtrail 24hrs' are visible.

Installation Type 1: Standalone GPS Tracking

Diagram

Diagram shows the AC200GPS3G module. Required connections are indicated: Black wire to Ground, Red wire to 12V(+), and White wire to Ignition. Optional connections are Green for Starter Kill (-), Yellow for Input (-), and Orange which is Not Used. A warning symbol ⚠️ is present with text stating: 'Applying 12V+ to the Brown or Blue Wire will void warranty'. A note clarifies: 'IC3 is NOT USED for GPS Tracking TYPE 1 installation'. The module is shown with 'THIS SIDE UP TOWARDS SKY' label.

Requirements

  • No Special Requirements

Installation Steps

  1. Install AC200 as per diagram above.
  2. Mount the Autoconnect module as described in the Autoconnect Install guide Step 3.

Programming and Testing

  1. Open the Autoconnect App or Dashboard.
  2. Log in to the Autoconnect device installed using the SID # as both username and password.
  3. Go to the command tab on the bottom of the app, or the remote function of the dashboard.
  4. Test GPS Tracking functions.
  5. We recommend affixing the SID Sticker to the door jamb of the vehicle.

Installation Type 2: Solace / Titan Elite Remote Starter

Diagram

Diagram shows the IC4 and IC3 modules, connected via RS232 Data Ports. A Bypass Module labeled 'iDatalink' or 'Fortin' is connected. Optional connections are Green (Starter Kill -), Yellow (Input -), Orange (Not Used). Required connections for IC3 are Black (Ground), Red (12V+), White (Ignition). A warning symbol ⚠️ is present with text stating: 'Applying 12V+ to the Brown or Blue Wire will void warranty'. A note indicates hardwiring these connections are optional for True Voltage readings. The module is shown with 'THIS SIDE UP TOWARDS SKY' label.

Requirements

  • Starter Firmware: 45 & Up
  • IC3 Firmware: Ver 22
  • IC3 Protocol Ver: IC3 Protocol 5 (SO/TI)

Installation Steps

  1. Complete installation of Remote Starter (R.S.) including programming the bypass module in the appropriate DATA protocol.
  2. For Fortin modules, you must switch the protocol using the Flashlink Manager. Turn option F2 AP/OFA to "ON". If you do not have a Flashlink Manager, you must hardwire all connections between the bypass module and R.S.
  3. Program R.S. for M2-11-1 (iDatalink 2-way) for Fortin and iDatalink modules.
  4. Connect Data link cable from IC3 to R.S. RS232 bypass module port, and also the IC3 to bypass module. (Ports are interchangeable on IC3).
  5. For true voltage cut and hardwire the Red, Black, and White directly from the Autoconnect device to the vehicle.
  6. DO NOT CUT THE DATALINK CABLE
  7. Mount the Autoconnect module as described in the Autoconnect Install guide Step 3.

Programming and Testing

  1. Open the Autoconnect App or Dashboard.
  2. Log in to the Autoconnect device installed using the SID # as both username and password.
  3. Go to the command tab on the bottom of the app, or the remote function of the dashboard.
  4. Scroll to the bottom of the commands and send the required Installer Protocol.
  5. For iDatalink and Fortin Modules select IC3 Protocol 5 (This is on by Default).
  6. Test all the application functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC. GPS).
  7. We recommend affixing the SID Sticker to the door jamb of the vehicle.

Installation Type 3: Fortin EVO-ALL (Standalone FW)

Diagram

Diagram shows the AC200GPS3G module connected to a Fortin EVO-ALL module via a RS232 Data Port. A 'REQUIRED DATALINK CABLE MODIFICATION' note indicates swapping BLUE & WHITE wires or cutting/reconnecting. Optional connections are Green (Starter Kill -), Yellow (Input -), Orange (Not Used). Required connections for IC3 are Black (Ground), Red (12V+), White (Ignition). A warning symbol ⚠️ is present with text stating: 'Applying 12V+ to the Brown or Blue Wire will void warranty'. A note indicates hardwiring these connections are optional for True Voltage readings. The module is shown with 'THIS SIDE UP TOWARDS SKY' label.

Requirements

  • IC3 Firmware: Ver 22
  • IC3 Protocol Ver: IC3 Protocol 2 (FORF)
  • Bypass Program: Option H2 Fortin RF

Installation Steps

  1. Program EVO-ALL as per Fortin installation instructions for vehicle. (Ensuring to select option H2 in Flashlink Manager) or visit http://fortin.ca/download/20101/autoconnect_evo-all.pdf
  2. Complete installation as per Fortin installation diagram including the programming of the bypass module.
  3. Ensure you have swapped the BLUE & WHITE wires on datalink cable between the IC3 and Fortin module.
  4. Connect Data link cable from IC3 to RS232 port on EVO-ALL (Ports are interchangeable on IC3). Connect Power and Ground if not using a T-Harness.
  5. For true voltage cut and hardwire the Red, Black, and White directly from the Autoconnect device to the vehicle.
  6. DO NOT CUT THE DATALINK CABLE
  7. For Fortin EVO-ALL select IC3 Protocol 2 (FORF).
  8. Program the Autoconnect to Fortin module by performing the following:
    • Hold programming button while inserting datalink cable to EVO-ALL. Release button when Blue & Red LED's Turn on.
    • Press and hold the programming button on the EVO-ALL (The LED's will turn off then back on approx 5 seconds), release button.
    • Turn Ignition ON (ALL 3 LED's should be on now).
    • Send the Lock command from the Autoconnect. The Blue and Red LED's should flash once.
    • Turn Ignition OFF.
  9. Mount the Autoconnect module as described in Autoconnect Install.

Programming and Testing

  1. Open the Autoconnect App or Dashboard.
  2. Log in to the Autoconnect device installed using the SID # as both username and password.
  3. Go to the command tab on the bottom of the app, or the remote function of the dashboard.
  4. Test all the application functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC. GPS).
  5. We recommend affixing the SID Sticker to the door jamb of the vehicle.

Installation Type 4: Fortin EVO-ONE

Diagram

Diagram shows the AC200GPS3G module connected to a Fortin EVO-ONE module via an RF PORT. A 'REQUIRED DATALINK CABLE MODIFICATION' note indicates swapping BLUE & WHITE wires or cutting/reconnecting. Optional connections are Green (Starter Kill -), Yellow (Input -), Orange (Not Used). Required connections for IC3 are Black (Ground), Red (12V+), White (Ignition). A warning symbol ⚠️ is present with text stating: 'Applying 12V+ to the Brown or Blue Wire will void warranty'. A note indicates hardwiring these connections are optional for True Voltage readings. The module is shown with 'THIS SIDE UP TOWARDS SKY' label.

Requirements

  • IC3 Firmware: Ver 22
  • IC3 Protocol Ver: IC3 Protocol 2 (FORF)
  • Bypass Program: Option H2 Fortin RF

Installation Steps

  1. Program EVO-ONE as per Fortin installation instructions for vehicle (Ensuring to select option H2 in Flashlink Manager) or visit http://fortin.ca/download/26701/autoconnect_evo-one.pdf
  2. Complete installation as per Fortin installation diagram.
  3. Ensure you have swapped the BLUE & WHITE wires on datalink cable between the IC3 and Fortin module.
  4. Connect Data link cable from IC3 to BLUE RF PORT on EVO-ONE (Ports are interchangeable on IC3).
  5. For true voltage cut and hardwire the Red, Black, and White directly from the Autoconnect device to the vehicle.
  6. DO NOT CUT THE DATALINK CABLE
  7. For Fortin EVO-ONE select IC3 Protocol 2 (FORF).
  8. Program the Autoconnect to Fortin module by performing the following:
    • Turn Ignition On.
    • Press and hold the Valet switch until LED flashes then release. Then press Valet switch 5x.
    • Press and release the brake pedal.
    • Send the Lock command from the Autoconnect. The park lights will flash once to confirm.
    • Press and release the brake pedal then turn ignition OFF.
  9. Mount the Autoconnect module as described in the Autoconnect Install guide Step 3.

Programming and Testing

  1. Open the Autoconnect App or Dashboard.
  2. Log in to the Autoconnect device installed using the SID # as both username and password.
  3. Go to the command tab on the bottom of the app, or the remote function of the dashboard.
  4. Test all the application functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC. GPS).
  5. We recommend affixing the SID Sticker to the door jamb of the vehicle.

Installation Type 5: ADS AL-CA (Standalone FW)

Diagram

Diagram shows the AC200GPS3G module connected to an ADS AL-CA module via a RS232 Data Port. A 'REQUIRED DATALINK CABLE MODIFICATION' note indicates swapping BLUE & WHITE wires or cutting/reconnecting. Optional connections are Green (Starter Kill -), Yellow (Input -), Orange (Not Used). Required connections for IC3 are Black (Ground), Red (12V+), White (Ignition). A warning symbol ⚠️ is present with text stating: 'Applying 12V+ to the Brown or Blue Wire will void warranty'. A note indicates hardwiring these connections are optional for True Voltage readings. The module is shown with 'THIS SIDE UP TOWARDS SKY' label.

Requirements

  • IC3 Firmware: Ver 22
  • IC3 Protocol Ver: IC3 Protocol 1 (TELE)
  • Bypass Program: Drone Telemetics

Installation Steps

  1. Program ADS-AL-CA as per iDatalink instructions for vehicle using a Weblink cable and choose Drone Telematics Kit.
  2. Complete installation as per iDatalink installation diagram.
  3. Ensure you have swapped the BLUE & WHITE wires on datalink cable between the IC3 and iDatalink module.
  4. Connect Data link cable from IC3 to RS232 Port on ADS-AL-CA (Ports are interchangeable on IC3).
  5. Connect Power and Ground to either IC3 or DATALINK cable.
  6. For true voltage cut and hardwire the Red, Black, and White directly from the Autoconnect device to the vehicle.
  7. DO NOT CUT THE DATALINK CABLE
  8. Mount the Autoconnect module as described in the Autoconnect Install guide Step 3.

Programming and Testing

  1. Open the Autoconnect App or Dashboard.
  2. Log in to the Autoconnect device installed using the SID # as both username and password.
  3. Go to the command tab on the bottom of the app, or the remote function of the dashboard.
  4. Scroll to the bottom of the commands and send the required Installer Protocol.
  5. For ADS-AL-CA select IC3 Protocol 1 (TELE).
  6. Test all the application functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC. GPS).
  7. We recommend affixing the SID Sticker to the door jamb of the vehicle.

Installation Type 6: ADS iDatastart (Classic, BM&BZ, VWx, HCx)

Diagram

Diagram shows the AC200GPS3G module connected to an ADS iDatastart module via a TELEMATICS PORT. Optional connections are Green (Starter Kill -), Yellow (Input -), Orange (Not Used). Required connections for IC3 are Black (Ground), Red (12V+), White (Ignition). A warning symbol ⚠️ is present with text stating: 'Applying 12V+ to the Brown or Blue Wire will void warranty'. A note indicates hardwiring these connections are optional for True Voltage readings. The module is shown with 'THIS SIDE UP TOWARDS SKY' label.

Requirements

  • IC3 Firmware: Ver 22
  • IC3 Protocol Ver: IC3 Protocol 1 (TELE)
  • Bypass Program: Drone Telematics

Installation Steps

  1. Program IDATASTART as per iDatalink instructions for vehicle using a Weblink cable and choose Drone Telematics Kit.
  2. Complete installation as per iDatalink installation diagram.
  3. Connect Data link cable from IC3 to BLUE TELEMATICS Port on iDATASTART (Ports are interchangeable on IC3).
  4. For true voltage cut and hardwire the Red, Black, and White directly from the Autoconnect device to the vehicle.
  5. DO NOT CUT THE DATALINK CABLE
  6. Mount the Autoconnect module as described in the Autoconnect Install guide Step 3.

Programming and Testing

  1. Open the Autoconnect App or Dashboard.
  2. Log in to the Autoconnect device installed using the SID # as both username and password.
  3. Go to the command tab on the bottom of the app, or the remote function of the dashboard.
  4. Scroll to the bottom of the commands and send the required Installer Protocol.
  5. For iDatastart Modules select IC3 Protocol 1 (TELE).
  6. Test all the application functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC. GPS).
  7. We recommend affixing the SID Sticker to the door jamb of the vehicle.

Installation Type 7: Compustar (CM6x00 & CM7x00 Series)

Diagram

Diagram shows the AC200GPS3G module connected to a Compustar module (CM6x00 or CM7x00) via an RS232 Data Port. A note states: 'IF USING A CM6x00 BRAIN YOU MUST USE A BLADE OR HARDWIRE A BYPASS MODULE'. Optional connections are Green (Starter Kill -), Yellow (Input -), Orange (Not Used). Required connections for IC3 are Black (Ground), Red (12V+), White (Ignition). A warning symbol ⚠️ is present with text stating: 'Applying 12V+ to the Brown or Blue Wire will void warranty'. A note indicates hardwiring these connections are optional for True Voltage readings. The module is shown with 'THIS SIDE UP TOWARDS SKY' label.

Requirements

  • IC3 Firmware: Ver 22
  • IC3 Protocol Ver: IC3 Protocol 1 (TELE)

Installation Steps

  1. Complete installation of Remote Starter (R.S.). If using CM6X00, use either BLADE or hardwire installation. If using CM7X00, use other DATALINK PORT.
  2. Connect Data link cable from IC3 to R.S. RS232 bypass module port. (Ports are interchangeable on IC3).
  3. For true voltage cut and hardwire the Red, Black, and White directly from the Autoconnect device to the vehicle.
  4. DO NOT CUT THE DATALINK CABLE
  5. Mount the Autoconnect module as described in the Autoconnect Install guide Step 3.

Programming and Testing

  1. Open the Autoconnect App or Dashboard.
  2. Log in to the Autoconnect device installed using the SID # as both username and password.
  3. Go to the command tab on the bottom of the app, or the remote function of the dashboard.
  4. Scroll to the bottom of the commands and send the required Installer Protocol.
  5. For Compustar Remote starters use IC3 Protocol 1 (TELE).
  6. Test all the application functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC. GPS).
  7. We recommend affixing the SID Sticker to the door jamb of the vehicle.

Installation Type 8: DEI (DBALL2/3, 4x10 / 5x10)

Diagram

Diagram shows the AC200GPS3G module connected to a DEI module (DBALL2/3, 4x10 / 5x10) via a D2D PORT. A '*Required White - Ignition' label is present. Optional connections are Green (Starter Kill -), Yellow (Input -), Orange (Not Used). Required connections for IC3 are Black (Ground), Red (12V+), White (Ignition). A warning symbol ⚠️ is present with text stating: 'Applying 12V+ to the Brown or Blue Wire will void warranty'. A note indicates hardwiring these connections are optional for True Voltage readings. The module is shown with 'THIS SIDE UP TOWARDS SKY' label.

Requirements

  • IC3 Firmware: Ver 22
  • IC3 Protocol Ver: IC3 Protocol 3 (D2D)
  • Bypass Program: SMART START enabled
  • Parts: D2D to DATA CABLE

Installation Steps

  1. Program DEI Module as per installation instructions for vehicle (Ensure to have the SMART START Option ENABLED).
  2. Complete installation as per installation diagram.
  3. Connect Data link cable from IC3 to D2D Port on DEI Module (Ports are interchangeable on IC3). IGNITION MUST BE HARDWIRED TO VEHICLE.
  4. Mount the Autoconnect module as described in the Autoconnect Install guide Step 3.

Programming and Testing

  1. Once the Autoconnect App or Dashboard.
  2. Log in to the Autoconnect device installed using the SID # as both username and password.
  3. Go to the command tab on the bottom of the app, or the remote function of dashboard.
  4. Scroll to the bottom of the commands and send the required Installer Protocol.
  5. For DEI Modules select IC3 Protocol 3 (D2D).
  6. Test all the application functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC. GPS).
  7. We recommend affixing the SID Sticker to the door jamb of the vehicle.

Installation Type 9: DEI (REMOTE STARTERS with ESP2)

Diagram

Diagram shows the AC200GPS3G module connected to a DEI module (REMOTE STARTERS with ESP2) via an ESP2 PORT. A '* Required White - Ignition' label is present. Optional connections are Green (Starter Kill -), Yellow (Input -), Orange (Not Used). Required connections for IC3 are Black (Ground), Red (12V+), White (Ignition). A warning symbol ⚠️ is present with text stating: 'Applying 12V+ to the Brown or Blue Wire will void warranty'. A note indicates hardwiring these connections are optional for True Voltage readings. The module is shown with 'THIS SIDE UP TOWARDS SKY' label.

Requirements

  • IC3 Firmware: Ver 22
  • IC3 Protocol Ver: IC3 Protocol 3 (ESP2)
  • Parts: ESP2 to DATA CABLE

Installation Steps

  1. Complete R.S Installation.
  2. Connect Data link cable from IC3 to ESP2 Port on DEI Module (Ports are interchangeable on IC3). 12V, GROUND, & IGNITION MUST BE HARDWIRED TO VEHICLE.
  3. Mount the Autoconnect module as described in the Autoconnect Install guide Step 3.

Programming and Testing

  1. Open the Autoconnect App or Dashboard.
  2. Log in to the Autoconnect device installed using the SID # as both username and password.
  3. Go to the command tab on the bottom of the app, or the remote function of the dashboard.
  4. Scroll to the bottom of the commands and send the required Installer Protocol.
  5. For DEI Remote starters select IC3 Protocol 4 (ESP2).
  6. Test all the application functions (Start, Stop, Lock, Unlock, Auxiliaries, ETC. GPS).
  7. We recommend affixing the SID Sticker to the door jamb of the vehicle.

LED Diagnostics

Red LED

Diagram shows the IC3 module with a red LED indicator.

FLASHING

  • Quick flashes: FW Verison Number (e.g., 2 quick then 2 quick = Ver 22)
  • Slow flashes: Data Protocol Version (e.g., 5 Flashes = IC3 Data Protocol 5 (SO/TI))

Solid

  • Solid ON: Ignition ON
  • Solid OFF: Ignition OFF

White LED

Diagram shows the IC3 module with a white LED indicator.

FLASHING

  • 1 Flash: AC200 to Device
  • 2 Flashes: Device to AC200

Supported Functions by Device Type

MANUFACTURER SOLACE/TITAN EVO-ALL/ONE 4X10/5X10 (D2D) DBALL (D2D) Viper S/A (W/ESP2) iDatastart (TELE) MID-CITY ENG (ALL GEN) COMPUSTAR (CM6/CM7 SERIES)
IC3 FW VERISON 22-1-1 Installer Program 5 Installer Program 2 Installer Program 3 Installer Program 3 Installer Program 4 Installer Program1 Installer Program 1 Installer Program 1
PROTOCOL VERSION REQUIRED (SO/TI) (FORF) (DEI 1) (DEI 1) (DEI 2) (TELE) (TELE) (TELE)
DOOR LOCK Y Y Y Y Y Y Y Y
DOOR UNLOCK Y Y Y Y Y Y Y Y
TRUNK RELEASE Y Y Y Y Y Y Y Y
AUX OUTPUT Y Y Y Y Y Y Y (START/STOP) Y
IGNITION ON/OFF W/ TAKEOVER Y Y Y Y Y Y Y (PULSE OFF/ON) Y
RUNTIME ON START Y Y N N N Y Y Y
ACTIVATE PANIC MODE Y N/Y (EVO-ONE) N N Y Y Y Y
ACTIVATE STARTER KILL Y (AC200) Y (AC200) Y (AC200) Y (AC200) Y (AC200) Y (AC200) Y (AC200) Y (AC200)
DEACTIVATE STARTER KILL Y (AC200) Y (AC200) Y (AC200) Y (AC200) Y (AC200) Y (AC200) Y (AC200) Y (AC200)
TEMPERATURE REQUEST Y N/Y (EVO-ONE) N N N NOT SUPPORTED NOT SUPPORTED Y
VOLTAGE REQUEST Y (AC200) Y (AC200) Y (AC200) Y (AC200) Y (AC200) Y (AC200) Y (AC200) Y (AC200)
BULLS EYE POSITION REQUEST Y (AC200) Y (AC200) Y (AC200) Y (AC200) Y (AC200) Y (AC200) Y (AC200) Y (AC200)
AUXILIARY 1 Y (IF APPLICABLE) Y (IF APPLICABLE) Y (IF APPLICABLE) Y (IF APPLICABLE) N Y (IF APPLICABLE) Y (If Vehicle Supports) Y (IF VEHICLE SUPPORTS)
AUXILIARY 2 Y (IF APPLICABLE) Y (IF APPLICABLE) Y (IF APPLICABLE) Y (IF APPLICABLE) Y (IF APPLICABLE) Y (IF APPLICABLE) Y (If Vehicle Supports) Y (IF VEHICLE SUPPORTS)
AUXILIARY 3 Y (IF APPLICABLE) Y (IF APPLICABLE) Y (IF APPLICABLE) Y (IF APPLICABLE) Y (IF APPLICABLE) Y (IF APPLICABLE) Y (If Vehicle Supports) Y (IF VEHICLE SUPPORTS)
AUXILIARY 4 Y (IF APPLICABLE) Y (IF APPLICABLE) Y (IF APPLICABLE) Y (IF APPLICABLE) N Y (IF APPLICABLE) Y (If Vehicle Supports) Y (IF VEHICLE SUPPORTS)
AUXILIARY 5 Y (P. THRU) N N N N N N N
AUXILIARY 6 Y (P. THRU) N N N N N N N
CAR FINDER Y N N N N N N N
EXTEND RUN TIME Y Y (Reset to Set time) N N N N N Y
RUN TIME REMAINING Y Y N N N Y Y Y
STOP REMOTE STARTER Y Y Y Y Y Y Y Y
VALET MODE: ENTER Y N (NOT SUPPORTED) N (NOT SUPPORTED) N (NOT SUPPORTED) N (NOT SUPPORTED) N (NOT SUPPORTED) N (NOT SUPPORTED) N (NOT SUPPORTED)
VALET MODE: EXIT Y N (NOT SUPPORTED) N (NOT SUPPORTED) N (NOT SUPPORTED) N (NOT SUPPORTED) N (NOT SUPPORTED) N (NOT SUPPORTED) N (NOT SUPPORTED)
ALARM SOUNDING Y Y Y Y Y Y N Y
INTRUSION DOOR Y Y Y Y Y Y N Y
INTRUSION TRUNK N Y Y Y Y Y N Y
INTRUSION HOOD Y Y Y Y Y Y N Y
ALARM SOUNDING IGNITION N N N N N N N N
FAILED START HOOD Y Y Y Y Y N Y (ALARM SOUNDING ONLY) Y
FAILED START BRAKE Y Y (GENERAL) N N N Y N Y
FAILED START TACH Y Y (GENERAL) N N N Y N Y
FAILED START VALET Y Y (GENERAL) N N N Y N N
FAILED START RESERVATION Y Y (GENERAL) N N N N N Y (GENERAL)
3-AC200GPS3G-COMMANDER-Quick-Install-Guide-Full Acrobat Distiller 15.0 (Macintosh)

Related Documents

Preview AutoConnect AC202: Quick Start and Installer Guide
This guide provides quick start instructions and detailed installation procedures for the AutoConnect AC202 vehicle tracking and remote start module, covering nine different installation types and essential testing procedures.
Preview Autoconnect AC200GPS3G: Vehicle Tracking & Remote Start Installation Guide
Install and activate your Autoconnect AC200GPS3G system. This guide provides detailed instructions for GPS tracking, remote start integration, and essential setup for installers. Learn about wiring, programming, and testing.
Preview Autoconnect AC200GPS3G Quick Start and Installation Guide
A comprehensive guide for installers on activating and installing the Autoconnect AC200GPS3G vehicle tracking and control system, including integration with Fortin EVO-ALL and EVO-ONE modules. Covers features, wiring, programming, testing, and LED diagnostics.
Preview AutoConnect AC202GPS: Vehicle Controls & Real-Time GPS Tracking System
Discover the AutoConnect AC202GPS, a comprehensive system for remote vehicle control, security, and real-time GPS tracking. Manage your car from your smartphone, monitor status, and track location with advanced reporting features.