Outdoor | Indoor | Lighting | LED | Architectural | TechLighting
Instruction Manual for Lightology models including: 920ENTRACL3 Entra CL3 Round Or Square Type IC Air Tight, 920ENTRACL3, Entra CL3 Round Or Square Type IC Air Tight, Square Type IC Air Tight, IC Air Tight, Air Tight, Tight
1A Install the Housing with Adjustable Bars 1 2 3 Determine which direction the adjustable bars need to be mounted, they can either be mounted horizontally or vertically.
File Info : application/pdf, 8 Pages, 590.07KB
DocumentDocumentInstallation Instructions for Entra CL3 Round or Square Type IC, Air-tight New Construction Adjustable LED Housing 920ENTRACL3 ENCL3_ 1.02 ENTRA GENERAL PRODUCT INFORMATION: This product is suitable for indoor locations. This product can be dimmed with a standard electronic dimmer. This instruction shows a typical installation. CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°C supply conductors. SAVE THESE INSTRUCTIONS! ROUND SHOWN SQUARE SHOWN 2 Install the Housing with Adjustable Bars 1A STOP POINT 3 TAB NAIL 2 2 2 2 2 OUTER ADJUSTABLE BAR INNER ADJUSTABLE BAR OUTER ADJUSTABLE BAR 2 INNER ADJUSTABLE BAR 2 NAIL 1B 6 5 NAIL COLLAR 6 5 NAIL JOIST 6 5 NOTE: The adjustable bars can be mounted to joists that are spaced 16" - 24" apart. 5 Align the bottom of the end plates with the bottom of the ceiling joists. 6 Level the adjustable bars and, with a hammer, tap the nails completely into the joists to secure the adjustable bars in place. 2 2 1 Determine which direction the adjustable bars need to be mounted, they can either be mounted horizontally or vertically. 2 Slide the inner adjustable bar completely through the two slots. Make sure flange at bottom of hanger bar ends is orientated with the bottom of the housing. 3 Slide and push the outer adjustable bar completely onto the inner adjustable bar so that the tab clicks into place behind the stop point. This will prevent the adjustable bars from coming apart. 4 Repeat steps 1 & 2 for the other side of the housing. 3 1C ADJUSTABLE BAR HOUSING 6 SCREW 6 COLLAR 7 6 6 Connect Power to the Housing 2A TAB ELECTRICAL BOX COVER 1 Push the tab on the housing electrical box up and remove the electrical box cover. 2B CONDUIT 6 7 HOUSING COLLAR 6 6 6 B DRIVER SCREW 7 7 6 6 6 Adjust the collar's position (horizontal position) by sliding the housing on adjustable bars. 7 When the desired location is achieved, tighten the screws to lock the housing onto the adjustable bars. 2 Install the conduit to the housing electrical box. 3 Run the power line wires into the housing electrical box. 4 Use the following wiring diagram to wire your fixture. 5 Make sure to cap 0-10V dimming wires if not being used. NOTE: Notches in collar can be used to align multiple housings using a laser or string. HOT BLACK DRIVER NEUTRAL WHITE GREY PURPLE HOUSING GROUND EXTERNAL HOT EXTERNAL NEUTRAL 0-10V (-) DIM 0-10V (+) DIM EXTERNAL GROUND 4 Install Drywall 3A 3-3/4" Install the Plaster Ring (Flangeless Version Only) 4A 3-3/4" SQUARE SHOWN ROUND COLLAR SQUARE COLLAR SQUARE SHOWN 2 2 1 Mark an appropriate sized diameter circle or square on drywall. Cut out the marked section. Note: The drywall may be cut by running a 1/8" RotoZip around the outside of the collar. 3B HOUSING 2 2 2 Install the provided 6x20 self-drilling screws through the plaster plate and housing at the marked locations. Do not place screws at any of the other mud holes on the plate. 4B SQUARE SHOWN DRYWALL 2 COLLAR 3 2 Align the cut out section of drywall with the collar and install drywall. 3 Properly plaster onto the plaster ring and drywall. 4C SQUARE SHOWN 4 4 Finish around the fixture to match drywall. 5 Assemble the Fixed or Adjustable Trim/Light Module 5A SQUARE SHOWN Assemble the Wall Wash Light Module 6A TRIM (SEE NOTE) SPRING CLIP LIGHT MODULE OPTIC REFLECTOR NOTE: Trim is included with flanged versions only. Skip this step for flangeless versions where plaster ring is provided. 1 Press the spring clips inward and feed the reflector through the trim until they snap together. 5B SQUARE SHOWN OPTIC HOLDER 1 Remove and discard optic holder and optic from fixed light module. 6B LIGHT MODULE ARROWS REFLECTOR LIGHT MODULE WALL WASH REFLECTOR 2 Snap light module and wall wash reflector together 2 Carefully snap light module and reflector together. Alignment arrows are provided on the adjustable versions. Directional alignment is not required for fixed Versions. 6 Install the Light Module 7A HOUSING 7C HOUSING LIGHT MODULE SPRING CLIP SPRING CLIP SPRING CLIP PORT WITH 2 BLACK LINE 4 4 B PORT MARKED "B" LIGHT MODULE 4 Release the spring clips to secure in place 1 Connect the jumper cable to the housing wire making sure the port marked "B" is paired with the port with a black line. 7B HOUSING SPRING CLIP 2 LIGHT MODULE 2 2 Push the spring clips inward. 3 Insert the light module through the collar and into housing. 7 Adjust the Module (Adjustable Versions Only) 8A SQUARE ADJUSTABLE SHOWN Install or Replace Optics and Lenses/Louvers 9A LIGHT MODULE LIGHT MODULE REFLECTOR 1 Using your fingers, adjust the direction of the light making sure to turn the module not the reflector (see note below). NOTE: The light module may be rotated up to 45 degrees when inside the housing. Remove the module from the housing to rotate another 45 degrees if necessary, then carefully reinstall the module into the OPTIC OPTIC HOLDER 1 Unscrew and remove the optic holder from the light module. 2 Remove the old optic. 3 If installing a lens or louver, remove the rubber gasket from the optic holder to allow room for lens or louver installation. If not installing a lens or louver, skip this step. NOTE: Only one lens or louver may be installed at a time. 4 Install the new optic into the optic holder. 5 Make sure the lens, louver, optic or gasket are properly seated in the optic holder, then screw the optic holder back onto the light module ©2022 Tech Lighting, L.L.C. All rights reserved. The Tech Lighting logo is a registered trademark of Tech Lighting. Tech Lighting reserves the right to change specifications for product improvements without notification. 8 7400 Linder Ave., Skokie, IL 60077 T 847.410.4400 | F 847.410.4500 www.techlighting.com