Instruction Manual for ASSOCIATED models including: 20178 Team Associated Reflex Hoonicorn, 20178, Team Associated Reflex Hoonicorn, Associated Reflex Hoonicorn, Reflex Hoonicorn, Hoonicorn
Team Associated Reflex 14R Hoonicorn 1/14 Street Car RTR | Planet-RC Modellbau Racing Shop
2 :: Introduction Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new vehicle. Please take a moment to read through the manual and familiarize yourself with the steps. We are continually changing and improving our designs; therefore, actual parts may appear slightly different than the illustrations. New parts will be noted on supplementary sheets located in the appropriate parts bags. Check each bag for these sheets before you start to build. :: RC14R RTR Features · Reflex 14R with licensed 1965 Ford Mustang Hoonigan Hoonicorn and officially licensed American Racing VF503 Wheels · Injection molded brake calipers and rotors with 12mm hex · 2.4GHz 2-channel radio system · Reedy brushed speed control and 3-pole brushed motor · High-Torque Digital Servo with spring-style servo saver · Molded front universals and rear dog bones · Sealed front and rear gear differentials · Center spool with 58T spur (70T included) and protective cover · Bushings with Oilite® coating · Molded one-piece tie rods and steering links · Adjustable body post height locations · Molded front and rear shock towers with adjustable shock positions · Fluid damped coilover shock absorbers · Molded tub chassis with covered center driveshaft · Adjustable battery tray · Aluminum center driveshaft · Serrated wheel screw with 2.0mm hex and 5.5mm nut drive · Foam front bumper :: Table of Contents 1................... Cover 4 - 5............. Quick Start Guide 2................... Introduction 6 - 17............Steps 1- 33 3...................1:1 Hardware "Fold Out" :: Notes 18................ Back Cover There is a 1:1 hardware foldout page in the front of the manual. To check the size of a part, line up your hardware with the correct drawing until you find the exact size. Each part in the foldout has a number assigned to it for ordering replacement parts. ! This symbol indicates a special note or instruction in the manual. :: Additional Your new Reflex 14R RTR comes assembled. The following items are needed for completion · 6-cell NiMh or 2 LiPo battery · Suitable battery charger · (4) AA batteries Tools included: · Multi-wrench :: Other Helpful Items · Silicone Shock Fluid · Reamer / Hole Punch (#1499) · Wire Cutters · Needle Nose Pliers · FT Dual Turnbuckle Wrench (#1114) · Silicone Diff Fluid · Body Scissors (AE Part # 1737) · Shock Pliers (#1681) · FT Hex/Nut Wrenches (AE Part # 1519) · Soldering Iron · Green Slime shock lube (AE Part # 1105) · Hobby Knife · Calipers or a Precision Ruler · FT Universal Tire Balancer (#1498) Associated Electrics, Inc. 21062 Bake Parkway Lake Forest, CA 92630 Customer Service Tel: 949.544.7500 Fax: 949.544.7501 http://www.RC10.com · http://twitter.com/Team_Associated · http://www.instagram.com/teamassociatedrc/ · http://www.facebook.com/TeamAssociated/ 3 :: Hardware - 1:1 Scale View Cap Head (shcs) Flat Head (fhcs) Bushings 2.5x12mm (8691) 2.5x10mm (21546) 4x7x2.5mm (21580) Button Head (bhcs) Flat Head (fhst) 4x8x3mm (21580) 2.5x3mm (89201) 2.5x6mm (31520) 3x6mm (31531) Button Head (bhst) 2.5x12mm (21582) Set Screws 2.6x6mm (21546) 2.6x8mm (21546) 2.6x10mm (21546) 2x8mm (21546) 2.6x8mm (21546) 2.6x10mm (21546) 7x11x3mm (21580) 8x12x3.5mm (21580) Shims and Washers 3x2.5mm (31500) 3x3mm (25225) 3x8mm (4670) 2.7x6.7x0.5mm (21546) 4x8x0.5mm (21516) Pin Nuts (lock/plain) 1.5x3.8 (21516) M2.5 Locknut (89215, 21546) Notes: 4 :: Quick Start Guide Battery Charging Steps and Safety: Remove the battery from the vehicle before charging. Place battery on a fire resistant surface. Avoid any contact with water or other liquids. Be sure to select the correct charging mode for the type of battery you are charging. ALWAYS use a compatible charger for charging your batteries. Caution: Never leave the battery unattended while charging. Always disconnect the charger from the power source when finished charging. Caution: Always disconnect the battery when you are finished driving the vehicle. :: Quick Start Guide - (cont.) Battery Installation: 1. Install the battery with the battery wires directed towards the rear of the vehicle. 2. Secure the battery strap using two body clips. 1 2 Peak Detection Quick Charger :: Quick Start Guide - (cont.) Battery Notes and Tip: Connect the battery as shown. Disconnect the battery when not in use! LiPo: LiPo batteries (lithium polymer) are high current rechargeable batteries. LiPo batteries offer extended run time and peak performance over NiMH batteries. They require a peak detection charger designed specifically for LiPo batteries. These batteries require special care and handling. LiPo batteries are recommended for advanced users only! ALWAYS charge a LiPo battery in LiPo mode. 3/23 5 :: Quick Start Guide - (cont.) Radio System Tuning and Controls: RULE: Transmitter on First/Vehicle on Second, Vehicle off First/ Transmitter off Last! 1) Slide the battery cover to remove cover. 2) Install alkaline or rechargeable AA size batteries into the battery holder. 3) Slide the battery cover back into place making sure it is completely closed and secure. 4) Turn the power ON. If the power indicator LED fails to light, check the batteries for insufficient contact or incorrect polarity. On/Off Switch :: Quick Start Guide - (cont.) Radio System Tuning and Controls: DO NOT hold the trigger when turning on the radio. If using optional battery for transmitter, be sure to plug it in correctly. Plugging in a battery backwards can cause damage. Refer to Radio owners manual for more in-depth instructions on radio operation and functions. Adjust steering trim with this knob so wheels point straight. Push trigger for Brake Pull trigger for Throttle Throttle set to Neutral! Neutral Install body and body clips. Ready to go! 6 :: Step 1 21516 Washer 4x8x0.5mm 21530 O-Ring 3.8 x 1mm 21529 Diff case 21524 Diff outdrive :: Step 2 21529 Diff sun gear 21516 Pin 1.5 x 6mm 21516 Washer 4x8x0.5mm 21530 O-Ring 3.8 x 1mm 21529 Diff cap 21524 Diff outdrive 21529 Diff sun gear 21516 Pin 1.5 x 6mm 21529 Diff cross pin 21529 x3 Diff planetary gear #6588 black grease :: Step 3 21546 x3 M2x8mm FHST 21526 Diff ring gear (37T) 21580 x2 8x12x3.5mm bushing Build 2 (1 front, 1 rear) :: Step 4 21577 Center outdrive ! Install pin before installing outdrive into spool mount! :: Step 5 21516 Pin 1.5 x 6mm 7 21573 Spur gear spool mount 21527 Spur gear, 58T (Kit) Spur gear 70T (Included) 21546 x3 M2x8mm FHST 21580 4x8x3mm bushing 21580 8x12x3.5mm bushing 21516 Pin 1.5 x 6mm ! Install pin before bushing! 21526 Pinion gear (15T) 21580 8x12x3.5mm bushing :: Step 6 Top of set screw head ! should be flush with the top of the chassis 4670 x4 3x8mm set screw 21516 Pin 1.5 x 6mm 21570 Chassis 8 :: Step 7 21577 Outdrive center, front 21516 Pin 1.5 x 6mm :: Step 8 21577 Drive shaft 21580 x2 4x8x3mm bushing 21526 Pinion gear (15T) 21504 Drive shaft cover 21504 Drive shaft cap 21546 x10 M2.6x8mm BHST 21504 Gear box cap, rear :: Step 9 21505 Steering bellcrank (right) 21510 x2 Steering post 31732 x4 4x7x2.5mm bearing 21505 Steering bellcrank (left) 21504 Gear box cap, front 21509 x2 Hat bushing 21522 x2 Ball stud 12.5mm 21546 x2 M2.6x8mm BHST 21573 Steering rack :: Step 10 21546 x2 M2.6x8mm BHST 21546 x2 Washer 2.7x0.5mm 31520 x2 M2.5x6mm BHCS 21504 Top plate 21505 Battery Mount, (front) :: Step 11 21505 Wire clip 21505 Servo Mount 21573 Shock tower, front :: Step 12 21573 Shock tower support, rear 21546 x4 M2.5x10mm FHCS 21546 x2 M2.6x10mm BHST 21546 x4 M2.6x8mm BHST 21573 Shock tower, rear 21546 x6 M2.6x8mm BHST 9 21505 Battery Mount, (rear) 21546 x2 M2.5x10mm FHCS 10 :: Step 13 21574 x2 Front suspension arms 21579 x2 Inner hinge pin, 3x47mm 21501 Arm mount, B 21501 x2 Arm mount bushing 21501 Arm mount, A :: Step 14 21574 x2 Front arm spacers 21575 Caster block, left 21546 x2 M2.6x8mm BHST 21575 Steering block, left 21573 Skid plate, front :: Step 15 21576 Universal drive shaft 21546 x6 M2.5x10mm FHCS 21522 x2 Ball stud 12.5mm 21523 x2 Caster block bushings 21580 x2 7x11x3mm bushing Build left and right sides! 21546 M2.6x8mm BHST 21546 x2 M2.6x10mm BHST 21575 Wheel hex 25225 M3x3mm set screw 21579 Outer hinge pin, 2x22mm 21575 Brake caliper Build left and right sides! 11 :: Step 16 21574 x2 Rear suspension arms 21501 Arm mount, C 21579 x2 Inner hinge pin, 3x47mm 21501 x2 Arm mount bushing 21501 Arm mount, D :: Step 17 21574 x2 Rear arm spacers 21501 Skid plate, rear 21546 x6 M2.5x10mm FHCS :: Step 18 21579 Outer hinge pin, 2x22mm 25225 M3x3mm set screw Build left and right sides! 21576 Dog bone, rear 21546 x2 M2.6x8mm BHST 21577 Axle, rear 21575 Rear hub, right 21580 x2 7x11x3mm bushing 21575 Wheel hex 21173 x2 Body clip 21546 x2 M2.6x8mm BHST 21546 M2.6x8mm BHST 21574 x2 Body post, rear, right 21575 Brake caliper 21574 x2 Body post stand 21574 x2 Body post, rear, left 12 :: Step 19 Build x2 (right and left side) 21577 x2 Ballstud 4.3mm 21574 Rod end link 21577 x2 Ballstud 4.3mm 21574 21582 x2 Rod end link M2.5x12mm BHST :: Step 20 21571 Shock body s8h0okck#f5lu4i4d8 21571 Shock shaft 21571 Shock holder 21577 Rod end ball, 4.3mm :: Step 21 21582 x2 M2.5x12mm BHST 21574 Rod end link 21571 Shock spring collar 21572 Shock spring 21571 Shock Spring cup Build x4 (x2 front, x2 rear) 21577 Ballstud, 4.3mm 21582 x2 M2.5x12mm BHCS 21577 Ballstud, 4.3mm 21582 x2 M2.5x12mm BHCS Build x2 (right and left side) :: Step 22 21573 Front bumper mount 21546 x2 M2.5x10mm FHCS :: Step 23 31520 x2 M2.5x6mm BHCS 31500 M3x2.5mm set screw 21532 Pinion gear, 16T :: Step 24 21574 x2 Body post stand 21173 x2 Body clip 21574 x2 Body post, front 21573 Front bumper foam 21546 x3 M2.5x10mm FHCS Brushed motor 21531 Motor mount cam 21546 x6 M2.6x10mm BHST, silver 21504 Center diff cap 21531 Motor mount insert Set The Gear Mesh: To set the gear mesh, push the teeth of the motor mount cam #21531 into the corresponding tooth pattern of the motor mount insert. Once the teeth are seated, you should be able to rock the spur gear back and forth without making the pinion gear move. Exessive amounts of spur gear movement (loose gear mesh) will cause premature gear failure. If the spur gear mesh is tight, there will be no movement between the spur and pinion gears. A gear mesh that is too tight or too loose will reduce power and damage the gear teeth. 21501 Bottom spur cap (58T) 21546 x2 M2.5x8mm FHST 13 14 :: Step 25 21514 x2 Steering link ball Cup 21513 Steering link rod Steering Link 17.40mm 21505 Servo saver 21522 Pivot ball 21546 M2x8mm FHST :: Step 26 21546 x4 M2.6x8mm BHST 21546 x4 Washer 2.7x0.5mm 21546 M2x8mm FHST 21522 Pivot ball 21546 x2 M2.6x10mm BHST 21505 ESC mount 21546 M2.6x8mm BHST Steering servo Receiver 6727 Servo tape :: Step 27 21173 x2 Body clips Battery ESC 21505 Battery strap 6727 Servo tape :: Step 28 :: Step 29 21566 - Printed 21567 - Clear Hoonicorn body, bumper 21568 Diffuser :: Step 30 21568 Spoiler 15 31531 x2 M3x6mm BHCS 21568 x2 Spacer nut 21569 x2 Reflex 14R Hoonicorn mounted wheel and tire, rubber 21583 x2 Wheel screw Install x4 wheel/tires 21568 x2 Taillight nut 31531 x2 M3x6mm BHCS 21568 x2 Taillight bucket 31520 x2 M2.5x6mm BHCS 21568 x2 Spacer nut 21566 - Printed 21567 - Clear Hoonicorn body 31520 x2 M2.5x6mm BHCS 89215 x2 M2.5mm Locknut 16 :: Step 31 21568 Turbo, right side :: Step 32 21568 Turbo, left side 31520 Manifold 21568 M2.5x6mm BHCS 21173 x4 Body clips 89201 x3 M2.5x3mm BHCS :: Step 33 17macOS Version 11.7.10 (Build 20G1427) Quartz PDFContext Vorschau