Hayward OmniPL Retrofit Installation Quick Start Guide

Pre-Installation Checklist

• Networked ColorLogic lights must be set in "Standalone" mode or they will fail to operate after the upgrade.
• All equipment settings and schedules will be lost after the upgrade.
• This upgrade will convert the old control to the Omni family of products and will require Omni specific accessories. Old remote controls, AQL2-BASE antennas and AQL-CHEM Sense and Dispense will no longer be compatible after the upgrade.
• For systems using a Hayward Ecostar VSP running firmware version less than R3.0.5 (pumps built before 2014), a Hayward SPX3400LCD display must be purchased and installed on the EcoStar pump if variable speed operation is desired with the Omni automation control. If single speed control is desired, no changes are necessary.
• Power is removed to all equipment in the system.
• All safety precautions have been read in the Installation manual.
• All parts listed in the Installation manual are included in the box.
• All of the necessary tools and mounting hardware have been gathered (drill, drill bits, Phillips & flathead screwdrivers, level, wire cutters/strippers, mounting anchors and fasteners).
• The Controller will be mounted a maximum of 15' from the OmniPL and will be mounted a minimum of 6' horizontal distance from the pool or spa.

1. Record Current Configuration and Wiring

Set ColorLogic Network lights into standalone mode before proceeding! All settings will be lost after upgrading. Before starting the installation, record all of the current settings and connections using the worksheets in the Installation manual. If there are accessories being used (ColorLogic lights, AQL-CHEM Sense and Dispense, etc.), you may have additional settings beyond what is covered in the worksheets. A Connection Table is provided to record all connected equipment. All of this information will be used to configure the new OmniPL and return your system to its original function.

2. Access Mainboard

With power disconnected to the control, remove the door by opening, then lifting up and off of the hinges. Remove the deadfront panel, this will not be reused. Remove the keypad by pulling straight out (away from the mainboard) and disconnecting cable. Record the location of all wiring connections by taking a photo or writing them down.

Action: Pull keypad straight out, away from the mainboard.

Tip: Take a photo of all the wiring connections to aid in the installation.

3. Remove Wiring from Old Mainboard

After taking a photo, start removing the wiring from the printed circuit board (PCB). The green terminal blocks can be lifted off of the old board without the need to remove individual wires. Except for AquaLogic, these terminal blocks will connect to the new board in exactly the same manner. For AquaLogic, remove the individual wires that will be used and attach to the OmniPL mainboard separately. Many of the connections from the old board will connect to the new OmniPL board at the same locations. Some high voltage wiring will be removed and not used. Refer to the callouts for each of the connections shown below in the diagram.

Diagram Descriptions:

• Optional Remote displays and VSPs: Connections for optional remote displays and Variable Speed Pumps (VSPs).
• Wireless base receiver and AQL-CHEM Sense and Dispense connection: Connection point for wireless base receivers and AQL-CHEM Sense and Dispense accessories.
• Sensor inputs and external input interlock: Connections for sensors and external input interlocks.
• Heater outputs: Connections for heater outputs.
• Valve outputs: Connections for valve outputs.
• Flow switch: Connection for the flow switch.
• Turbo Cell: Connection for the Turbo Cell.
• Local display keypad connector: Connector for the local display keypad.
• Local display keypad removed: Indicates the local display keypad has been removed.
• Relay wiring: Wiring that plugs into an identical connector on the OmniPL PCB.
• Rectifier wiring (red, black, orange): These wires must be removed from both ends (PCB and rectifiers) and discarded. They are not used with the OmniPL PCB. Do not remove rectifiers to maintain enclosure integrity.
• Transformer wiring (yellow secondary, blue, purple, white, gray primary): Yellow wires are transformer secondary wires that connect to a wiring harness. Blue, purple, white, and gray wires are transformer primary wires that connect to a wiring harness.
• Input power wiring (black and white): Black and white wires that connect to a wiring harness.
• pH pump output wiring: Connections for an acid pump used to control pool pH. If used, this will need to be wired to a high voltage relay after the OmniPL PCB swap, as there is no pH pump output on the OmniPL PCB.

Website: www.hayward.com

Phone: 908-355-7995

4. Replace the Old PCB with the OmniPL PCB

Depending on your model, use either a screwdriver or 5/16 nut driver to loosen or remove the fasteners securing the old PCB to the enclosure. Slide the board up to remove. Place the new OmniPL PCB in the same location and secure with the original fasteners.

Action: Remove Old Board, Install New Board.

Instruction: Turn Over [➡️]

5. Mount Controller

The OmniPL Controller has a 15 ft cord which must plug into the OmniPL PCB. When considering a suitable mounting location, refer to the Pre-Installation Checklist on the front of this Quick Start Guide and mount in a location that is convenient for viewing and changing settings. Allow enough clearance above the enclosure so that the flip door can open fully.

A mounting template is provided in the Installation manual. To install, screw two appropriate fasteners into the mounting surface at the desired location as shown. Tighten until the bottom of the screw heads are 1/8" off the mounting surface then hang the Controller firmly on the screws.

Measurement: 2 7/8" clearance needed.

6. Install Wiring to OmniPL PCB

Connect the wiring from the old PCB to the new OmniPL PCB. Unless upgrading an AquaLogic, green terminal blocks can connect in the same locations as the old PCB. Refer to the wiring connection callouts below.

Wiring Connections:

• Smart Relays and VSP connections: Used for Smart Relays and VSP connections. Do not connect old remote displays to this connector.
• Sensors and interlocks: Except for AquaLogics, these connections are the same as the old board. Connect sensors and interlocks here. Refer to the PCB for the name of each connection.
• Heater(s): Except for AquaLogics, these connections are the same as the old board. Connect the heater(s) here.
• Valve outputs: Valve outputs are the same as the old board.
• Optional HL-CHEM Sense and Dispense accessory: Used for optional HL-CHEM Sense and Dispense accessory. Do not connect an old AQL2-BASE-RF wireless base station to this connector. Use the included rubber seal to plug hole in enclosure if needed.
• Optional HLWALLMOUNT remote control: Used for an optional HLWALLMOUNT remote control.
• OmniPL Controller connection: Connect the OmniPL Controller here.
• Flow Switch connectors: The OmniPL has two flow switch connectors. Either one can be used.
• TurboCell connector: TurboCell connector is the same as the old board.
• Internal relay connectors: Internal relay connectors are positioned the same as the old board. Relay wiring will connect to the same corresponding locations as the old PCB.
• Transformer Primary wiring harness: The transformer Primary wiring harness uses the four colors (blue, purple, white, gray) as a reference for each connection; blue to blue, purple to purple, etc. and plugs in as shown.
• Transformer Secondary wiring harness: The OmniPL secondary transformer wiring harness included in the kit plugs it into the mainboard as shown. Strip back wires 0.4" and attach two lever type wire nuts according to the diagram above. Locate the two yellow leads from the transformer secondary (refer to Step 3). Cut off the spade connectors and strip wires back 0.4". Insert stripped bare leads into the wire nuts and close the levers to secure. Be sure that no bare wire can be seen coming out of the wire nuts.
• Input power wiring harness: Locate the OmniPL input wiring harness included in the kit, plug it in to the mainboard as shown, and then cut to desired length. Strip back wires 0.4" and attach two lever type wire nuts as shown. Locate the black and white power leads. Cut off the spade connectors and strip wires back 0.4". Insert stripped bare leads into wire nuts and close levers to secure. Be sure that no bare wire can be seen coming out of the wire nuts.

7. Start Up, Configuration and Registration

With all connections complete, tuck back all the wiring to prepare for the deadfront installation. Locate the new deadfront and knockout all appropriate breaker locations. Install the new deadfront panel and reattach the door. Turn on power to the OmniPL. The OmniPL will power on and prompt you to begin configuration (see below). The Configuration Wizard will ask you general questions relating to your pool/spa and specific questions about connected pool equipment. Configuring the OmniPL requires knowledge of all of the connected pool equipment. Refer to your worksheets and Connection Table from Step 1 while configuring the OmniPL.

Configuration Interface Example:

Display shows: System configuration, Config wizard, System info, Backup config, Restore config, Display, Network, Web server, Date/time, Language, Component, MSP, Variable Speed Smart Relay, Smart IO Board.

System Info Example: MSP ID: 3233, Version R2.0.0, R0.2.15, X1.0.12, X1.0.6.

Temperature display example: Pool 82°F, Air 71°F.

Create an OmniLogic Account using OmniLogic App or PC:

Type "haywardomnilogic.com" into your web browser. Select "Register New User" at the bottom of the screen. Input your information on the following screen and select "Save". Make note of your user name and password on the lines provided to the left.

Register the OmniPL:

Log in to your new OmniLogic account. Read the disclaimer after logging in and press continue. Input your MSP ID on the following screen and fill out the remaining information.

Control your pool from the OmniLogic App or your PC:

Now that your OmniPL has been registered, you can control your pool remotely from your PC, laptop, or mobile device. For computers, go to haywardomnilogic.com and log in to your account. For mobile devices, download the OmniLogic app from your device's app store, then log in to your account.

OmniPL Operation:

For information about operation (turning on equipment, setting schedules, changing heater settings, etc.), refer to the OmniPL Retrofit Kit Operation manual.

Document Revision: 092779 RevA